Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1241/41    Low Battery Positive Voltage

for Preparation Click here


DESCRIPTION

If the voltage supplied to the IG1 terminal is not within the DTC detection threshold due to malfunctions in such as the battery and alternator circuit, this DTC is stored.

DTC No.
DTC Detection Condition
Trouble Area
C1241/41
When either of the following conditions is detected:
1. Both of the following conditions continue for at least 10 seconds.
  1. Vehicle speed is more than 2 mph (3 km/m).
  2. IG1 terminal voltage is less than 9.5 V.
2. All of the following conditions continue for at least 0.2 seconds.
  1. Solenoid relay remains ON.
  2. IG1 terminal voltage is less than 9.5 V.
  3. Relay contact is open.
  1. Battery
  2. ECU-IG fuse
  3. Charging system
  4. Power source circuit

WIRING DIAGRAM


C132918E01


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

1.INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
INSPECT CHARGING SYSTEM
OK


2.INSPECT ECU-IG FUSE
  1. Remove the ECU-IG fuse from the driver side J/B.

  1. Check the ECU-IG fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE ECU-IG FUSE
OK


3.READ VALUE OF INTELLIGENT TESTER (IG1 POWER SUPPLY)
  1. Install the ECU-IG fuse.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and push the intelligent tester main switch ON.

  1. Start the engine.

  1. Select "DATA LIST" mode on the intelligent tester.

    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    IG VOLTAGE
    ECU-IG power supply voltage / TOO LOW / NORMAL / TOO HIGH
    TOO LOW: 9.5 V or less
    NORMAL: 9.5 V or 14.0 V
    TOO HIGH: 14.0 V or more
    -

  1. Measure the voltage output from the ECU displayed on the intelligent tester.

    OK:
    "Normal" is displayed.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


4.INSPECT SKID CONTROL ECU (IG1 TERMINAL)


    C121700E79
  1. Install the ECU-IG fuse.

  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    S28-46 (IG1) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5.INSPECT SKID CONTROL ECU (GND TERMINAL)


    C124799E13
  1. Disconnect the skid control ECU (S29) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S28-1 (GND1) - Body ground
    Below 1 Ω
    S28-32 (GND2) - Body ground
    Below 1 Ω
    S29-4 (GND3) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


6.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTC is detected (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


    Result:

    Condition
    Proceed to
    DTC is output
    A
    DTC is not output (When troubleshooting in accordance with the DTC CHART)
    B
    DTC is not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    C



B
END

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A

REPLACE MASTER CYLINDER SOLENOID