Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1232/32    Stuck in Deceleration Sensor

DTC    C1234/34    Yaw Rate Sensor Malfunction

DTC    C1243/43    Acceleration Sensor Stuck Malfunction

DTC    C1244/44    Open or Short in Deceleration Sensor Circuit

DTC    C1245/45    Acceleration Sensor Output Malfunction

DTC    C1381/97    Yaw Rate and / or Acceleration Sensor Power Supply Voltage Malfunction

for Preparation Click here


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.
The yaw rate sensor has a built-in acceleration sensor.
If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, the DTC U0123/62 (yaw rate sensor communication trouble) and U0124/95 (acceleration sensor communication trouble) are output.
These DTCs are also output when the calibration has not been completed.

DTC No.
DTC Detection Condition
Trouble Area
C1232/32
At a vehicle speed of 6 mph (10 km/h) or more, the fluctuation range of the signal from either GL1 or GL2 is under 80 mV and the other is above 1.9 V for 30 seconds or more.
  1. Yaw rate and acceleration sensor
  2. Yaw rate and acceleration sensor circuit
  3. CAN communication system
C1234/34
Sensor malfunction signal is received from yaw rate sensor.
  1. Yaw rate and acceleration sensor
  2. Yaw rate and acceleration sensor circuit
  3. CAN communication system
C1243/43
The following condition repeats 16 times.
  1. GL1 and GL2 do not change by more than 2LSB when the vehicle decelerates from 19 mph (30 km/h) to 0 mph (0 km/h).
  1. Yaw rate and acceleration sensor
  2. Yaw rate and acceleration sensor circuit
  3. CAN communication system
C1244/44
When either of the following conditions is detected:
1. Both of the following conditions continue for at least 60 seconds.
  1. Vehicle is stopped.
  2. Difference between GL1 and GL2 does not drop below 0.4 G once it reaches 0.6 G or more.
2. Data malfunction signal is received from acceleration sensor.
  1. Yaw rate and acceleration sensor
  2. Yaw rate and acceleration sensor circuit
  3. CAN communication system
C1245/45
The following condition continues for at least 60 seconds.
  1. Difference between the values calculated from acceleration sensor value and vehicle speed exceeds 0.35 G.
  1. Yaw rate and acceleration sensor
  2. Yaw rate and acceleration sensor circuit
  3. CAN communication system
C1381/97
acceleration sensor power source malfunction signal is received for at least 10 seconds at a speed of more than 2 mph (3 km/h).
  1. Yaw rate and acceleration sensor
  2. Yaw rate and acceleration sensor power source circuit
  3. CAN communication system

WIRING DIAGRAM


C132917E02


INSPECTION PROCEDURE

NOTICE:
When replacing the yaw rate and acceleration sensor, perform zero point calibration (Click here).

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to the ON position.

  1. Check if the DTCs (U0073/94, U0123/62, C1210/36 and/or C1336/39) are detected (Click here).

    Result:

    Condition
    Proceed to
    DTC U0073/94, U0123/62, C1210/36 and/or C1336/39 are not output
    A
    DTC U0073/94 and/or U0123/62 are output
    B
    DTC C1210/36 and/or C1336/39 are output
    C



B
INSPECT CAN COMMUNICATION SYSTEM

C
REPAIR CIRCUIT INDICATED BY OUTPUT DTC
A


2.INSPECT YAW RATE AND ACCELERATION SENSOR (IG AND GND TERMINAL)


    F045082E24
  1. Disconnect the yaw rate and acceleration sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Y1-5 (IG) - Body ground
    Ignition switch ON
    10 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Y1-1 (GND) - Body ground
    Ignition switch OFF
    Below 1 Ω


    Result:

    Condition
    Proceed to
    OK (When troubleshooting in accordance with the DTC CHART)
    A
    OK (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    B
    NG
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG OR GND CIRCUIT)
A

REPLACE YAW RATE AND ACCELERATION SENSOR