Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1254/54    Pressure Switch Circuit

for Preparation Click here


DESCRIPTION

The accumulator pressure sensor is connected to the skid control ECU in the master cylinder solenoid.

C124776E02

HINT:
If the code (C1254/54) is output, the following conditions will occur:
  1. The ABS, VSC TRAC, and BRAKE warning lights and SLIP and VSC OFF indicator lights will come on.
  2. The skid control buzzer sounds.
  3. Control of all systems other than EBD is canceled.


DTC No.
DTC Detection Condition
Trouble Area
C1254/54
Accumulator pressure sensor malfunction
(Fluid pressure does not change when the pump operates or when the brake is applied.)
  1. Hydraulic brake booster
  2. Accumulator pressure sensor
  3. Master cylinder pressure sensor

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

1.READ VALUE OF INTELLIGENT TESTER (ACCUMULATOR PRESSURE SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 20 times.

  1. Turn the ignition switch to the ON position and push the intelligent tester main switch ON.

  1. Select "DATA LIST" mode on the intelligent tester.

    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    ACC PRESS
    Accumulator pressure sensor reading / Min.: 0 V, Max.: 5 V
    3.58 to 5 V
    If the value is constant regardless of pump operation, accumulator pressure sensor malfunction is suspected.

  1. Check the accumulator output value.

    Result:

    Condition
    Proceed to
    Output value is within the "Normal Condition" range
    A
    Output value is out of the "Normal Condition" range
    B
    Output value is constant regardless of pump operation
    B



B
REPLACE MASTER CYLINDER SOLENOID
A


2.READ VALUE OF INTELLIGENT TESTER (MASTER CYLINDER PRESSURE SENSOR)
  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 20 times.

  1. Install the brake pedal effort gauge (SST), and bleed air.

SST
09709-29018  
  1. Turn the ignition switch to the ON position and push the intelligent tester main switch ON.

  1. Select "DATA LIST" mode on the intelligent tester.

    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    MAS CYL PRESS 1
    Master cylinder pressure sensor 1 reading / Min.: 0 V, Max.: 5 V
    0.3 to 1.95 V
    With pedal effort of 49 N (5 kgf, 11 in.*Ibf)
    Front brake pressure: 1220 to 2320 kPa (11.4 to 23.7 kgf/cm2, 162 to 337 psi)

  1. Check that the master cylinder pressure sensor's output value is normal.

    OK:
    Master cylinder pressure sensor value is normal.



NG
REPLACE MASTER CYLINDER SOLENOID
OK


3.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 20 times.

  1. Turn the ignition switch to the ON position.

  1. Wait until the pump motor stops.

  1. Depress the brake pedal and release it.

  1. Wait for 25 minutes.

  1. Check if the same DTC is detected (Click here).

    Result:

    Condition
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID