Home › DRIVE LINE ยท VF4AM TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TRANSFER ASSEMBLY


    F043500
  1. Install the transfer assembly with the 8 bolts.

    Torque:
    24 N*m{ 240 kgf*cm , 17 ft.*lbf }

    NOTICE:
    Take care not to damage the adaptor rear oil seal with the transfer input gear spline.



2. INSTALL AUTOMATIC TRANSMISSION WITH TRANSFER


    D028727E01
  1. Install the automatic transmission assembly to the engine with the 9 bolts.

    Torque:
    17 mm head:
    71 N*m{ 720 kgf*cm , 53 ft.*lbf }
    14 mm head:
    37 N*m{ 380 kgf*cm , 27 ft.*lbf }



    F044115
  1. Install the 6 torque converter mounting bolts.

    Torque:
    48 N*m{ 490 kgf*cm , 35 ft.*lbf }

    HINT:
    First install the black colored bolt and then the remaining 5 bolts.

  1. Install the torque converter housing side cover to the engine.



3. CONFIRM FRONT DIFFERENTIAL ASSEMBLY


4. INSTALL MANIFOLD STAY NO.2
  1. Install the No. 2 manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



5. INSTALL MANIFOLD STAY
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



6. INSTALL STARTER ASSEMBLY

HINT:
(Click here for Standard or Click here for Cold Area)



7. CONNECT WIRE HARNESS


8. CONNECT CONNECTOR


9. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


    F042938E03
  1. Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

    Torque:
    A:
    72 N*m{ 735 kgf*cm , 53 ft.*lbf }

  1. Tighten the 4 bolts to the No. 3 frame crossmember sub-assembly and No. 1 engine mounting insulator rear.

    Torque:
    B:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



10. INSTALL TRANSFER CASE LOWER PROTECTOR


    F043499
  1. Install the transfer case lower protector with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



11. INSTALL NO. 1 TRANSFER CONTROL CABLE BRACKET


    G036547E01
  1. Install the No. 1 transmission control cable bracket to the transmission assembly with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



12. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    D028154E01
  1. Connect the transmission control cable assembly to the automatic transmission.

  1. Install the nut and clip on the transmission control cable assembly.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



13. INSTALL NO. 1 OIL COOLER INLET TUBE


    Z035557E01
  1. Using SST, tighten the No. 1 oil cooler inlet tube.

    SST
    09023-12701  

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }



14. CONNECT NO. 1 OIL COOLER OUTLET TUBE
  1. Temporarily install the No. 1 oil cooler outlet tube.

  1. Temporarily install the No. 1 oil cooler inlet tube.



  1. Install the 2 clamps and 2 bolts.

    Torque:
    5 N*m{ 50 kgf*cm , 43 in.*lbf }



    G038661

  1. Using SST, tighten the No. 1 oil cooler outlet tube.

    SST
    09023-12701  

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }



15. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


16. INSTALL FRONT SUSPENSION MEMBER BRACKET LH


    F042934
  1. Install the front suspension member bracket LH with the 4 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



17. INSTALL FRONT SUSPENSION MEMBER BRACKET
  1. Install the front suspension member bracket with the 4 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



18. ADD TRANSFER OIL


19. ADD AUTOMATIC TRANSMISSION FLUID

HINT:
(Click here)



20. INSPECT AUTOMATIC TRANSMISSION FLUID

HINT:
(Click here)



21. INSTALL PROPELLER SHAFT ASSEMBLY


    C098710E03
  1. Remove the SST from the extension housing.

    SST
    09325-40010  

  1. Install the propeller shaft assembly in the extension housing.



    C098711E02
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



22. INSTALL PROPELLER SHAFT ASSEMBLY FRONT


    C098708E06
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



    C098709E05
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



23. INSTALL EXHAUST PIPE ASSEMBLY

HINT:
(Click here)



24. CONNECT OXYGEN SENSOR

HINT:
(Click here)



25. INSTALL ENGINE UNDER COVER ASSEMBLY REAR

Torque:
29 N*m{ 296 kgf*cm , 21 ft.*lbf }



26. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Torque:
29 N*m{ 296 kgf*cm , 21 ft.*lbf }



27. INSPECT AUTOMATIC TRANSMISSION FLUID

HINT:
(Click here)



28. INSPECT SHIFT LEVER POSITION

HINT:
(Click here)



29. CHECK FOR EXHAUST GAS LEAKAGE


30. WARM UP


31. DRIVE TEST