Home › DRIVE LINE ยท VF4BM TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TRANSFER ASSEMBLY


    F043500
  1. Install the transfer assembly with the 8 bolts.

    Torque:
    24 N*m{ 240 kgf*cm , 17 ft.*lbf }

    NOTICE:
    Take care not to damage the adaptor rear oil seal with the transfer input gear spline.



2. INSTALL AUTOMATIC TRANSMISSION WITH TRANSFER

HINT:



3. INSTALL FLYWHEEL HOUSING UNDER COVER


    F042939
  1. Install the flywheel housing under cover and 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



4. CONNECT WIRE HARNESS


5. CONNECT CONNECTOR


6. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


    F042939
  1. Install the flywheel housing under cover and 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



7. INSTALL TRANSFER CASE LOWER PROTECTOR


    F043499
  1. Install the transfer case lower protector with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



8. INSTALL NO. 1 TRANSFER CONTROL CABLE BRACKET


    F042937
  1. Install the No. 1 transmission control cable bracket with 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



9. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Connect the transmission control cable with nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



10. INSTALL NO. 1 OIL COOLER INLET TUBE
  1. Using SST, tighten the No. 1 oil cooler inlet tube.

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }

    SST
    09023-12701  



11. CONNECT NO. 1 OIL COOLER OUTLET TUBE
  1. Temporarily install the No. 1 oil cooler outlet tube.

  1. Temporarily install the No. 1 oil cooler inlet tube.



    Z035556
  1. Install the 2 clamps and 2 bolts.

    Torque:
    5 N*m{ 50 kgf*cm , 43 in.*lbf }



    Z035557E01
  1. Using SST, tighten the No. 1 oil cooler outlet tube.

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }

    SST
    09023-12701  



12. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY
  1. Coat a new O-ring with ATF, and install them to the oil filler tube.

  1. Install the oil filler tube and bolt to the automatic transmission.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Install the ATF level gauge.



13. INSTALL FRONT SUSPENSION MEMBER BRACKET LH


    F042934
  1. Install the front suspension member bracket LH with 4 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



14. INSTALL FRONT SUSPENSION MEMBER BRACKET
  1. Install the front suspension member bracket with 4 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



15. ADD TRANSFER OIL

HINT:
(Click here)



16. ADD AUTOMATIC TRANSMISSION FLUID

HINT:
(Click here)



17. INSPECT AUTOMATIC TRANSMISSION FLUID


18. INSTALL PROPELLER SHAFT ASSEMBLY


    C098700E04
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



    C098699E04
  1. Align the matchmarks on the propeller shaft flange and transfer flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



19. INSTALL PROPELLER SHAFT ASSEMBLY FRONT


    C098708E06
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



    C098709E05
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



20. INSTALL EXHAUST PIPE ASSEMBLY

HINT:
(Click here)



21. CONNECT OXYGEN SENSOR

HINT:
(Click here)



22. INSTALL ENGINE UNDER COVER ASSEMBLY REAR


23. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


24. INSPECT AUTOMATIC TRANSMISSION FLUID

HINT:
(Click here)



25. INSPECT SHIFT LEVER POSITION

HINT:
(Click here)



26. CHECK FOR EXHAUST GAS LEAKAGE


27. WARM UP


28. DRIVE TEST