DTC P0300 Random / Multiple Cylinder Misfire Detected |
DTC P0301 Cylinder 1 Misfire Detected |
DTC P0302 Cylinder 2 Misfire Detected |
DTC P0303 Cylinder 3 Misfire Detected |
DTC P0304 Cylinder 4 Misfire Detected |
DTC P0305 Cylinder 5 Misfire Detected |
DTC P0306 Cylinder 6 Misfire Detected |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0300 | Simultaneous misfiring of several cylinders are detected (2 trip detection logic) |
|
| P0301 P0302 P0303 P0304 P0305 P0306 | Misfiring of specific cylinder is detected (2 trip detection logic) |
|
| Items | Contents |
| Terminals | #10 to #60 - E01 |
| Equipment Settings | 20 V/Division, 100 or 1 ms/Division |
| Conditions | Idling |


| Related DTCs | P0300: Random/multiple cylinder misfire detected P0301: Cylinder 1 misfire detected P0302: Cylinder 2 misfire detected P0303: Cylinder 3 misfire detected P0304: Cylinder 4 misfire detected P0305: Cylinder 5 misfire detected P0306: Cylinder 6 misfire detected |
| Required Sensors / Components (Main) | Injector, Ignition coil, Spark plug |
| Required Sensors / Components (Related) | Crankshaft position sensor, Camshaft position sensor, ECT sensor, IAT sensor, MAF meter |
| Frequency of Operation | Continuous |
| Duration | Every 1,000 revolutions (soon after engine is started: 1 time, other: 4 times) (emission related misfire) Every 200 revolutions (1 or 3 times) (catalyst deteriorating misfire) |
| MIL Operation | 2 driving cycles: Emission related misfire MIL flashes immediately: Catalyst damaged misfire |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | P0100, P0101, P0102, P0103 (MAF Sensor), P0110, P0112, P0113 (IAT Sensor), P0115, P0116, P0117, P0118 (ECT Sensor), P0120, P0121, P0122, P0123, P0220, P0222, P0223 , P2135 (TP Sensor), P0125 (Insufficient ECT for Closed Loop), P0327, P0328, P0332, P0333 (Knock Sensor), P0335 (CKP Sensor), P0340, P0342, P0343 (CMP Sensor), P0345 (VVT Sensor 1,2), P0500 (VSS), |
| Battery voltage | 8 V or more |
| VVT system | No operate by scan tool |
| Engine RPM | - |
| All of following conditions met | Condition 1 and 2 |
| Either of the following conditions is met | Condition (a) or (b) |
| (a) ECT at engine start | More than -7°C (19°F) |
| (b) ECT | More than 20°C (68°F) |
| Fuel cut | OFF |
| First 1,000 revolutions after engine start, or check mode | Crankshaft 1,000 revolutions |
| Except above | Crankshaft 1,000 revolutions x 4 |
| All of following conditions 1, 2 and 3 are met | Crankshaft 200 revolutions |
| 1. Driving cycle | 1st |
| 2. Check mode | OFF |
| 3. Engine RPM | Less than 2,800 rpm |
| Except above | Crankshaft 200 revolutions x 3 |
| Misfire rate | 2% or more (Automatic transmission) |
| Number of misfire per 200 revolutions | 77 or more (varies with intake air amount and RPM) |
| Paired cylinders misfire | Detected |
| MID | TID | Scaling | Description of Test Value | Minimum Test Limit | Maximum Test Limit |
| $A1 | $0B | Multiply by 1 [time] | Exponential Weighted Moving Average misfire counts for last 10 driving cycles - total | 0 | 65535 |
| $A1 | $0C | Multiply by 1 [time] | Misfire counts for last and current driving cycles - total | 0 | 65535 |
| MID | TID | Scaling | Description of Test Value | Minimum Test Limit | Maximum Test Limit |
| $A2 | $0B | Multiply by 1 [time] | Exponential Weighted Moving Average misfire counts for last 10 driving cycles - total | 0 | 65535 |
| $A2 | $0C | Multiply by 1 [time] | Misfire counts for last and current driving cycles - total | 0 | 65535 |
| MID | TID | Scaling | Description of Test Value | Minimum Test Limit | Maximum Test Limit |
| $A3 | $0B | Multiply by 1 [time] | Exponential Weighted Moving Average misfire counts for last 10 driving cycles - total | 0 | 65535 |
| $A3 | $0C | Multiply by 1 [time] | Misfire counts for last and current driving cycles - total | 0 | 65535 |
| MID | TID | Scaling | Description of Test Value | Minimum Test Limit | Maximum Test Limit |
| $A4 | $0B | Multiply by 1 [time] | Exponential Weighted Moving Average misfire counts for last 10 driving cycles - total | 0 | 65535 |
| $A4 | $0C | Multiply by 1 [time] | Misfire counts for last and current driving cycles - total | 0 | 65535 |
| MID | TID | Scaling | Description of Test Value | Minimum Test Limit | Maximum Test Limit |
| $A5 | $0B | Multiply by 1 [time] | Exponential Weighted Moving Average misfire counts for last 10 driving cycles - total | 0 | 65535 |
| $A5 | $0C | Multiply by 1 [time] | Misfire counts for last and current driving cycles - total | 0 | 65535 |
| MID | TID | Scaling | Description of Test Value | Minimum Test Limit | Maximum Test Limit |
| $A6 | $0B | Multiply by 1 [time] | Exponential Weighted Moving Average misfire counts for last 10 driving cycles - total | 0 | 65535 |
| $A6 | $0C | Multiply by 1 [time] | Misfire counts for last and current driving cycles - total | 0 | 65535 |
| MID | TID | Scaling | Description of Test Value | Minimum Test Limit | Maximum Test Limit |
| $A7 | $0B | Multiply by 1 [time] | Exponential Weighted Moving Average misfire counts for last 10 driving cycles - total | 0 | 65535 |
| $A7 | $0C | Multiply by 1 [time] | Misfire counts for last and current driving cycles - total | 0 | 65535 |

| Engine RPM | Duration |
| Idling | 3.5 minutes or more |
| 1,000 | 3 minutes or more |
| 2,000 | 1.5 minutes or more |
| 3,000 | 1 minute or more |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE TO DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 | A |
| P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs | B |
|
| ||||
| A | |
| 2.READ VALUE OF INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / MISFIRE / MISFIRE RPM and MISFIRE LOAD.
Read and note the MISFIRE RPM and MISFIRE LOAD (engine load) values.
| NEXT | |
| 3.CHECK PCV HOSE CONNECTIONS |
|
| ||||
| OK | |
| 4.CHECK MISFIRE COUNT (CYL #1, #2, #3, #4, #5 AND #6) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the tester on.
Clear DTCs (Click here).
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / MISFIRE / CYL #1, #2, #3, #4, #5 and #6 (Procedure "A").
Allow the engine to idle.
Read each value of CYL #1 to #6 displayed on the tester (Procedure "B").
Shift the gear selector lever to the D position.
Repeat procedures "A" to "B" above.
Check the CYL #1 to #6.
If misfire counts are still not displayed, perform procedures "C" and "D" and then check the misfire counts again.
Drive the vehicle with the MISFIRE RPM and MISFIRE LOAD noted in step 2 (Procedure "C").
Read the CYL #1 to #6 or DTCs displayed on the tester (Procedure "D").
| Misfire Count | Proceed to |
| One or two cylinders have misfire counts | A |
| Three cylinders or more have misfire counts | B |
|
| ||||
| A | |
| 5.CHECK SPARK PLUG |
![]() |
Remove the ignition coil and the spark plug of the misfiring cylinder.
Measure the spark plug electrode gap.
Check the electrode for carbon deposits.
| Manufacturers | Products |
| DENSO | K20HR-U11 |
| NGK | LFR6C-11 |
|
| ||||
| OK | |
| 6.CHECK FOR SPARKS AND IGNITION |
Disconnect the injector connectors, in order to prevent the engine from starting.
Install the spark plug to the ignition coil, and connect the ignition coil connector.
Attach the spark plug assembly to the cylinder head cover.
Crank the engine for less than 2 seconds and check the spark.
Reconnect the injector connectors.
|
| ||||
| OK | |
| 7.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| NG | ||
| ||
| 8.CHANGE NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER |
Change the installed spark plug to a spark plug that functions normally.
Perform a spark test.
Install the spark plug to the ignition coil and connect the ignition coil connector.
Disconnect the injector connector.
Ground the spark plug.
Check if sparks occur while the engine is being cranked.
|
| ||||
| NG | ||
| ||
| 9.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND/OR #60 VOLTAGE) |
![]() |
Turn the ignition switch on.
Measure the voltage between the terminals of the E4 and E6 ECM connector.
| Tester Connections | Specified Conditions |
| #10 (E6-2) - E01 (E4-7) | 9 to 14 V |
| #20 (E6-3) - E01 (E4-7) | 9 to 14 V |
| #30 (E6-4) - E01 (E4-7) | 9 to 14 V |
| #40 (E6-5) - E01 (E4-7) | 9 to 14 V |
| #50 (E6-6) - E01 (E4-7) | 9 to 14 V |
| #60 (E6-7) - E01 (E4-7) | 9 to 14 V |
|
| ||||
| NG | |
| 10.CHECK HARNESS AND CONNECTOR (INJECTOR - ECM) |
![]() |
Disconnect the injector connector (of the misfiring cylinder).
Disconnect the E6 ECM connector.
Turn the ignition switch on.
Measure the resistance and voltage between the injector and the ECM connector terminals.
| Tester Connections | Specified Conditions |
| I9-1 - Ground | 11 to 14 V |
| I9-2 - Ground | 10 kΩ or higher |
| I9-2 - #10 (E6-2) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| I10-1 - Ground | 11 to 14 V |
| I10-2 - Ground | 10 kΩ or higher |
| I10-2 - #20 (E6-3) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| I11-1 - Ground | 11 to 14 V |
| I11-2 - Ground | 10 kΩ or higher |
| I11-2 - #30 (E6-4) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| I12-1 - Ground | 11 to 14 V |
| I12-2 - Ground | 10 kΩ or higher |
| I12-2 - #40 (E6-5) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| I13-1 - Ground | 11 to 14 V |
| I13-2 - Ground | 10 kΩ or higher |
| I13-2 - #50 (E6-6) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| I13-1 - Ground | 11 to 14 V |
| I13-2 - Ground | 10 kΩ or higher |
| I13-2 - #60 (E6-7) | Below 1 Ω |
Reconnect the injector connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER |
Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 12.CHECK VALVE CLEARANCE (MISFIRING CYLINDER) |
|
| ||||
| OK | |
| 13.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage.
|
| ||||
| OK | |
| 14.CHECK VALVE TIMING |
Remove the cylinder head cover .
Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
If not, turn the crankshaft 1 revolution (360°), then align the marks as above.
Reinstall the cylinder head cover .
|
| ||||
| OK | |
| 15.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 16.READ VALUE OF INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / COOLANT TEMP.
Read the COOLANT TEMP twice, when the engine is cold and also when warmed up.
|
| ||||
| OK | |
| 17.READ VALUE OF INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / MAF and COOLANT TEMP.
Allow the engine to idle until the COOLANT TEMP reaches 75°C (167°F) or more.
Read the MAF with the engine in an idling condition and at an engine speed of 2,500 rpm.
|
| ||||
| OK | ||
| ||