DTC P0450 Evaporative Emission Control System Pressure Sensor / Switch |
DTC P0451 Evaporative Emission Control System Pressure Sensor Range / Performance |
DTC P0452 Evaporative Emission Control System Pressure Sensor / Switch Low Input |
DTC P0453 Evaporative Emission Control System Pressure Sensor / Switch High Input |
| DTCs | Monitoring Items | Malfunction Detection Conditions | Trouble Areas | Detection Timings | Detection Logic |
| P0450 | Pressure sensor abnormal voltage fluctuation | Sensor output voltage rapidly fluctuates beyond upper and lower malfunction thresholds for 0.5 seconds. |
|
| 1 trip |
| P0451 | Pressure sensor noising | Sensor output voltage fluctuates frequently in certain time period. |
|
| 2 trip |
| P0451 | Pressure sensor stuck | Sensor output voltage does vary in certain time period. |
| EVAP monitoring (ignition OFF) | 2 trip |
| P0452 | Pressure sensor voltage low | Sensor output voltage is less than 0.45 V for 0.5 seconds. |
|
| 1 trip |
| P0453 | Pressure sensor voltage high | Sensor output voltage is more than 4.9 V for 0.5 seconds. |
|
| 1 trip |

| Related DTCs | P0450: Evaporative emission control system pressure sensor/switch chattering P0451: Evaporative emission control system pressure sensor noise P0451: Evaporative emission control system pressure sensor stuck P0452: Evaporative emission control system pressure sensor/switch low input P0453: Evaporative emission control system pressure sensor/switch high input |
| Required Sensors / Components | Pump module |
| Frequency of Operation | Once pre driving cycle |
| Duration | 0.5 seconds: P0450, P0452, P0453 Within 15 seconds: P0451 |
| MIL Operation | Immediate: P0450, P0452, P0453 2 driving cycles: P0451 |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Atmospheric pressure | 70 to 110 kPa (525 to 825 mmHg) |
| Battery voltage | 10.5 V or more |
| IAT | 4.4 to 35°C (40 to 95°F) |
| EVAP pressure sensor malfunction (P0450, P0452, P0453) | Not detected |
| Either of the following conditions is met | Condition 1 or 2 |
| 1. Time after key off | 5 or 7 or 9.5 hours |
| 2. Engine condition | Running |
| Battery voltage | 10.5 V or more |
| IAT | 4.4 to 35°C (40 to 95°F) |
| EVAP pressure sensor malfunction (P0450, P0452, P0453) | Not detected |
| Atmospheric pressure | 70 to 110 kPa (525 to 825 mmHg) |
| Time after key off | 5 or 7 or 9.5 hours |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Frequency that EVAP pressure change is 0.3 kPa (2.25 mmHg) or more | 10 times or more in 10 seconds |
| EVAP pressure change during reference pressure measurement | Less than 0.65 kPa (4.9 mmHg) |
| EVAP pressure | Less than 42.11 kPa (315.82mmHg), or more than 123.761 kPa (928.207 mmHg) |
| EVAP pressure | Less than 42.11 kPa (315.82 mmHg) |
| EVAP pressure | More than 123.761 kPa (928.207 mmHg) |

| 1.CONFIRM DTC AND EVAP PRESSURE |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (do not start the engine).
Turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / VAPOR PRESS.
Read the EVAP (Evaporative Emission) pressure displayed on the tester.
| Display (DTC Output) | Test Results | Suspected Trouble Areas | Proceed to |
| P0451 | - | Pressure sensor | C |
| P0452 | Less than 45 kpa (338 mmHg) |
| A |
| P0453 | More than 120 kPa (900 mmHg) |
| B |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (PUMP MODULE - ECM) |
![]() |
Turn the ignition switch off.
Disconnect the E8 ECM connector.
Measure the resistance between PPMP terminal of the ECM connector and the body ground.
| Test Results | Suspected Trouble Areas | Proceed to |
| 10 Ω or less |
| A |
| 10 Ω or more |
| B |
Reconnect the ECM connector.
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (PUMP MODULE - ECM) |
![]() |
Disconnect the L4 canister connector.
Disconnect the E8 ECM connector.
Measure the resistance between PPMP terminal of the ECM connector and the body ground.
| Test Results | Suspected Trouble Areas | Proceed to |
| 10 kΩ or more | Short in pressure sensor circuit | A |
| 10 kΩ or less | Short in wire harness/connector (ECM - pressure sensor) | B |
Reconnect the canister connector.
Reconnect the ECM connector.
|
| ||||
| A | |
| 4.REPLACE CHARCOAL CANISTER ASSEMBLY |
Replace charcoal canister assembly (Click here).
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Wait for at least 60 seconds.
Select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.
| NEXT | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (PUMP MODULE - ECM) |
![]() |
Disconnect the L4 canister connector.
Turn the ignition switch on.
Measure the voltage and resistance of the L4 canister connector.
| Tester Connections | Specified Conditions |
| L4-4 - Body ground | Between 4.5 V and 5.5 V |
| L4-3 - Body ground | Between 4.5 V and 5.5 V |
| L4-2 - Body ground | 100 Ω or less |
| Test Results | Suspected Trouble Areas | Proceed to |
| Voltage and resistance is within standard ranges | Open in pressure sensor circuit | A |
| Voltage and resistance is outside standard ranges | Open in wire harness/connector (ECM - pressure sensor) | B |
Reconnect the canister connector.
|
| ||||
| A | |
| 6.REPLACE CHARCOAL CANISTER ASSEMBLY |
Replace charcoal canister assembly (Click here).
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Wait for at least 60 seconds.
Select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.
| NEXT | ||
| ||
| 7.REPAIR OR REPLACE WIRE HARNESS OR CONNECTORS |
Repair or replace wire harness or connectors.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Wait for at least 60 seconds.
Select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.
| NEXT | ||
| ||
| 8.REPLACE ECM |
Replace the ECM (Click here).
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Wait for at least 60 seconds.
Select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.
| NEXT | ||
| ||