TIMING CHAIN > REMOVAL |
| 1. REMOVE POWER STEERING LINK ASSEMBLY |
| 2. REMOVE DIFFERENTIAL CARRIER ASSEMBLY FRONT (for 4WD) |
| 3. DRAIN ENGINE COOLANT |
![]() |
Remove the service hole cover from the engine under cover.
Install a vinyl hose onto the drain on the radiator side.
Fix the vinyl hose with tape.
![]() |
Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.
Remove the radiator cap.
Drain the coolant from the reservoir tank.
Tighten the 3 drain plugs.
Remove the vinyl hose from the radiator.
| 4. DRAIN ENGINE OIL |
![]() |
Remove the engine under cover seal No. 3.
Remove the oil pan drain plug and drain the engine oil.
Clean the oil pan drain plug and install it with a new gasket.
| 5. REMOVE BATTERY |
| 6. REMOVE V-BANK COVER |
![]() |
Remove the 2 nuts, then remove the V-bank cover.
| 7. REMOVE RADIATOR SUPPORT SEAL UPPER |
Remove the 11 clips and radiator support seal upper.
| 8. LOOSEN FLUID COUPLING ASSEMBLY |
![]() |
Loosen the 4 fluid coupling bolts.
| 9. REMOVE FAN AND GENERATOR V BELT |
![]() |
While releasing the belt tension by turning the belt tensioner counterclockwise, remove the V-ribbed belt from the belt tensioner.
| 10. REMOVE FLUID COUPLING ASSEMBLY |
![]() |
Unfasten the hose clamp, and then separate the 2 oil cooler hoses from the fan shroud.
Disconnect the radiator reserve tank hose.
Remove the 2 fan shroud bolts and radiator reserve tank bolt.
Remove the 4 fluid coupling nuts, and then remove the fan with fluid coupling and fan shroud together.
Remove the fan pulley.
| 11. DISCONNECT NO. 2 VENTILATION HOSE |
| 12. REMOVE AIR CLEANER ASSEMBLY |
![]() |
Disconnect the ventilation hose No. 2.
![]() |
Disconnect the vacuum hose.
Disconnect the mass air flow meter connector.
Remove the 2 wire harness clamps.
![]() |
Loosen the 2 hose clamps.
Remove the 2 bolts, then remove the air cleaner.
| 13. REMOVE OIL LEVEL GAUGE GUIDE |
Remove the oil level gauge.
Remove the bolt and pull out the oil level gauge guide.
Remove the O-ring from the oil level gauge guide.
| 14. REMOVE WATER INLET |
| 15. SEPARATE VANE PUMP ASSEMBLY |
![]() |
Disconnect the P/S oil pressure switch connector.
Remove the 2 bolts, and separate the vane pump.
| 16. REMOVE GENERATOR ASSEMBLY |
![]() |
Disconnect the wire harness.
Remove the bolt and wire harness stay.
Disconnect the connector from the generator assembly.
Remove the terminal cap and nut.
Disconnect the wire harness from the terminal B.
![]() |
Remove the 2 bolts and wire harness clamp bracket from the generator assembly.
![]() |
Remove the 2 bolts and generator assembly.
| 17. SEPARATE COOLER COMPRESSOR ASSEMBLY |
![]() |
Remove the bolt and separate the suction hose sub-assembly.
Disconnect the cooler compressor assembly connector.
Remove the 4 bolts and separate cooler compressor assembly from the V-ribbed belt tensioner assembly.
| 18. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 5 bolts and V-ribbed belt tensioner.
| 19. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY |
Remove the 2 bolts and 2 idler pulleys.
| 20. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY |
Remove the bolt and idler pulley.
| 21. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, hold the crankshaft pulley and loosen the pulley set bolt.
![]() |
Using the pulley set bolt and SST, remove the crankshaft pulley.
| 22. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 10 bolts and 2 nuts.
![]() |
Insert the blade of SST between the oil pan and No. 2 oil pan, cut off applied sealer and remove the No. 2 oil pan.
| 23. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the 2 nuts, oil strainer and gasket.
| 24. REMOVE OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 4 housing bolts.
Remove the flywheel housing under cover.
![]() |
Remove the 17 bolts and 2 nuts.
![]() |
Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.
Remove the O-ring from the oil pump.
| 25. REMOVE INTAKE AIR SURGE TANK |
![]() |
Disconnect the 2 water by-pass hoses.
![]() |
Disconnect the fuel vapor feed hose.
![]() |
Disconnect the ventilation hose.
![]() |
Disconnect the 2 VSV connectors.
Disconnect the throttle body with motor connector.
Separate the 3 wire harness clamps and hose clamp.
![]() |
Remove the 2 bolts and throttle body bracket.
![]() |
Remove the bolt and oil baffle plate.
Remove the 4 bolts and 2 surge tank stays.
![]() |
Remove the 2 nuts.
Using a socket hexagon wrench 8, remove the 4 bolts, intake air surge tank and gasket.
| 26. REMOVE IGNITION COIL ASSEMBLY |
| 27. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.
| 28. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH |
![]() |
Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.
Remove the ventilation valve from the cylinder head cover.
| 29. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
Disconnect the 2 oil control valve connectors.
Remove the 2 bolts and 2 camshaft timing oil control valves.
| 30. REMOVE VVT SENSOR |
![]() |
RH bank side VVT sensor.
Disconnect the VVT sensor connector.
Remove the bolt and the VVT sensor.
![]() |
LH bank side VVT sensor.
Disconnect the water by-pass hoses No. 4 and No. 5.
Disconnect the VVT sensor connector.
![]() |
Remove the bolt and the VVT sensor.
| 31. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY |
![]() |
Remove the 15 bolts and 2 nuts.
![]() |
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
Remove the O-ring from the LH cylinder head.
| 32. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL |
| 33. SET NO. 1 CYLINDER TO TDC / COMPRESSION |
![]() |
Install the crankshaft pulley set bolt, and turn the crankshaft to align the crankshaft set key with the timing line of the cylinder block.
![]() |
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.
| 34. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
While turning the stopper plate of the tensioner clockwise, push in the plunger of the chain tensioner as shown in the illustration.
While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ3.5 mm (0.138 in.) into the holes on the stopper plate and tensioner to fix the stopper plate.
Remove the 2 bolts and chain tensioner.
| 35. REMOVE CHAIN TENSIONER SLIPPER |
| 36. REMOVE NO. 1 IDLE GEAR SHAFT |
![]() |
Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.
| 37. REMOVE NO. 2 CHAIN VIBRATION DAMPER |
Remove the 2 No. 2 chain vibration dampers.
| 38. REMOVE CHAIN SUB-ASSEMBLY |