Home › SUSPENSION & AXLE › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM

DTC    C1713/13    Right Rear Height Control Sensor Circuit

DTC    C1714/14    Left Rear Height Control Sensor Circuit

for Preparation Click here


DESCRIPTION

Inside the sensor, a brush integrated with the control sensor rotor shaft moves above the resistor, providing linear output. Since the resistance value between the brush and resistor terminal changes in proportion to the shaft rotation angle, the fixed voltage applied to the resistor by ECU is modified by the sensor and output to the ECU as a voltage indicating the shaft rotation angle.

DTC No.
DTC Detecting Condition
Trouble Area
C1713/13
With the ignition switch ON, a voltage of 4.7 V or more or 0.3 V or less at each height control sensor sub-assembly rear is detected for 1 sec.
  1. Height control sensor sub-assembly rear RH
  2. Right rear height control sensor circuit
  3. Suspension control ECU
C1714/14
  1. Height control sensor sub-assembly rear LH
  2. Left rear height control sensor circuit
  3. Suspension control ECU

HINT:
  1. Once the ECU stores DTC C1713/13 or C1714/14 in the memory, vehicle height control is suspended and not carried out until a normal signal is input to the ECU from the height control sensor sub-assembly. However, the control resumes if the ignition switch is turned OFF, and then turned ON again.
  2. When the suspension control ECU detects a malfunction in the height control sensor, the height control indicator light "N" comes on or blinks, and the height control switch ("HI" and "LO") is suspended.
  3. When either one of the right or left height control sensor sub-assembly is faulty, the suspension control ECU uses the other one (functioning one) to adjust the vehicle height to the normal height. When both of the height control sensor sub-assembly are faulty, the suspension control ECU suspend the height control function immediately.


WIRING DIAGRAM


F043223E01


INSPECTION PROCEDURE

HINT:
  1. Proceed to troubleshooting following the flow chart, regardless of whether or not DTC C1713/13 or C1714/14 is displayed.
  2. If DTC C1761/61 (ECU malfunction) and/or C1774/74 (power source circuit) is displayed, perform the inspection necessary for DTC C1761/61 (Click here) and/or C1774/74 (Click here) first.
    (If DTC C1761/61 and C1774/74 are output at the same time, perform the inspection necessary for DTC C1774/74 first.)
  3. Start the inspection from step 1 when using the intelligent tester, and start from step 2 when not using the intelligent tester.

1.READ VALUE OF INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position, and push the intelligent tester main switch ON.

  1. Select the item "RL HEIGHT" or "RR HEIGHT" in the DATA LIST, and read its value displayed on the intelligent tester.

  1. Check the vehicle height value of the height control sensor sub-assembly with the intelligent tester while pressing the height control switch "UP" or "DOWN".

    OK:
    Vehicle height value changes.



OK
REPLACE SUSPENSION CONTROL ECU
NG


2.CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL SENSOR SUB-ASSEMBLY REAR POWER SOURCE)


    F044277E01
  1. Disconnect the height control sensor sub-assembly rear LH and RH connectors.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    LH Side:
    Tester connection
    Condition
    Specified condition
    H15-1 (SHB) - H15-3 (SHG)
    Ignition switch ON
    4.5 to 5.5 V
    RH Side:
    Tester connection
    Condition
    Specified condition
    H16-1 (SHB) - H16-3 (SHG)
    Ignition switch ON
    4.5 to 5.5 V



OK
Go to step 4
NG


3.CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL SENSOR REAR - SUSPENSION CONTROL ECU)
  1. Disconnect the S13 suspension control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH Side:
    Tester connection
    Specified condition
    S13-22 (SBL2) - H15-1 (SHB)
    Below 1 Ω
    S13-23 (SHRL) - H15-2 (SHRL)
    Below 1 Ω
    S13-21 (SGL2) - H15-3 (SHG)
    Below 1 Ω
    S13-22 (SBL2) - S13-23 (SHRL)
    10 kΩ or higher
    S13-21 (SGL2) - S13-23 (SHRL)
    10 kΩ or higher
    S13-21 (SGL2) - S13-22 (SBL2)
    10 kΩ or higher
    RH Side:
    Tester connection
    Specified condition
    S13-20 (SBR2) - H16-1 (SHB)
    Below 1 Ω
    S13-24 (SHRR) - H16-2 (SHRR)
    Below 1 Ω
    S13-19 (SGR2) - H16-3 (SHG)
    Below 1 Ω
    S13-20 (SBR2) - S13-24 (SHRR)
    10 kΩ or higher
    S13-19 (SGR2) - S13-24 (SHRR)
    10 kΩ or higher
    S13-19 (SGR2) - S13-20 (SBR2)
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT HEIGHT CONTROL SENSOR SUB-ASSEMBLY REAR


    F044307E01
  1. Remove the height control sensor sub-assembly rear LH or RH.

  1. Connect 3 dry batteries of 1.5 V in series.

  1. Height control sensor sub-assembly rear LH:
    Connect terminal 1 (SHB) to the batteries' positive (+) terminal, and terminal 3 (SHG) to the batteries' negative (-) terminal, then apply approximately 4.5 V between terminal 2 (SHRL) and 3 (SHG) in the following conditions.

    Standard voltage:
    Position
    Voltage
    High (0° to 45°)
    Approx. 2.53 to 4.33 V
    Normal (0°)
    Approx. 2.53 V
    Low (0° to -45°)
    Approx. 0.81 to 2.53 V

    Result:
    Result
    Proceed to
    OK
    A
    NG
    B

  1. Height control sensor sub-assembly rear RH:
    Connect terminal 1 (SHB) to the batteries' positive (+) terminal, and terminal 3 (SHG) to the batteries' negative (-) terminal, then apply approximately 4.5 V between terminal 1 (SHG) and 2 (SHRR) in the following conditions.

    Standard voltage:
    Position
    Voltage
    High (0° to 45°)
    Approx. 2.53 to 4.33 V
    Normal (0°)
    Approx. 2.53 V
    Low (0° to -45°)
    Approx. 0.81 to 2.53 V

    Result:
    Result
    Proceed to
    OK
    A
    NG
    C



B
REPLACE HEIGHT CONTROL SENSOR SUB-ASSEMBLY REAR LH

C
REPLACE HEIGHT CONTROL SENSOR SUB-ASSEMBLY REAR RH
A

REPLACE SUSPENSION CONTROL ECU