Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY (for 1GR-FE)

AUTOMATIC TRANSMISSION ASSEMBLY (for 1GR-FE) > INSTALLATION

for Preparation Click here



1. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY


    D025544E03
  1. Using calipers and a straight edge, measure dimension A between the transmission and the end surface of the drive plate.



    G036653
  1. Aligning the matchmarks on the transmission case and torque converter assembly, engage the splines of the input shaft and turbine runner.



    G036654
  1. Engage the splines of the stator shaft and stator while turning the torque converter assembly.

    HINT:
    Turn the torque converter assembly approximately 180°.



    G036655
  1. Turn the torque converter assembly and align the matchmarks on the torque converter assembly and transmission case to engage the key of the oil pump drive gear into the slot on the torque converter assembly. (procedure "1")

    NOTICE:
    Do not push on the torque converter when aligning the matchmarks.



    G036541E01
  1. Using calipers and a straight edge, measure dimension B shown in the illustration and check that B is greater than A measured in procedure "1".

    Standard:
    A + 1 mm (0.03937 in.) or more



2. INSTALL NO.1 TRANSMISSION CONTROL CABLE BRACKET


    G036547E01
  1. Install the No. 1 transmission control cable bracket to the transmission assembly with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



3. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


    D028727E01
  1. Install the automatic transmission assembly to the engine with the 9 bolts.

    Torque:
    17 mm head:
    71 N*m{ 720 kgf*cm , 53 ft.*lbf }
    14 mm head:
    37 N*m{ 380 kgf*cm , 27 ft.*lbf }



    F044115
  1. Install the 6 torque converter mounting bolts.

    Torque:
    48 N*m{ 490 kgf*cm , 35 ft.*lbf }

    HINT:
    First install the black colored bolt and then the remaining 5 bolts.

  1. Install the torque converter housing side cover to the engine.



4. INSTALL NO.1 REAR ENGINE MOUNTING INSULATOR


    G036651E05
  1. Install the No. 1 rear engine mounting insulator to the automatic transmission with the 4 bolts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



5. INSTALL NO.2 MANIFOLD STAY


6. INSTALL MANIFOLD STAY


7. INSTALL STARTER ASSEMBLY

HINT:
(Click here for Standard or Click here for Cold Area)



8. CONNECT CONNECTOR


    G038651E01
  1. Connect the speed sensor SP2 connector.



    G039387E10
  1. Install the wire harness with the bolt.

    Torque:
    8.0 N*m{ 83 kgf*cm , 71 in.*lbf }

  1. Connect the speed sensor NT connector (a).

  1. Connect the transmission wire connector (b).

  1. Connect the park/neutral position switch assembly connector (c).



9. INSTALL NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY


    F042938E03
  1. Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

    Torque:
    A:
    72 N*m{ 735 kgf*cm , 53 ft.*lbf }

  1. Tighten the 4 bolts to the No. 3 frame crossmember sub-assembly and No. 1 engine mounting insulator rear.

    Torque:
    B:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



10. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    D028154E01
  1. Connect the transmission control cable assembly to the automatic transmission.

  1. Install the nut and clip on the transmission control cable assembly.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



11. INSTALL NO.1 OIL COOLER OUTLET TUBE
  1. Temporarily install the No. 1 oil cooler outlet tube.

  1. Temporarily install the No. 1 oil cooler inlet tube.



  1. Install the 2 clamps and 2 bolts.

    Torque:
    5 N*m{ 50 kgf*cm , 43 in.*lbf }



    G038661

  1. Using SST, tighten the No. 1 oil cooler outlet tube.

    SST
    09023-12701  

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }



12. INSTALL NO.1 OIL COOLER INLET TUBE


    Z035557E01
  1. Using SST, tighten the No. 1 oil cooler inlet tube.

    SST
    09023-12701  

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }



13. INSTALL FRONT SUSPENSION MEMBER BRACKET LH


    F042934
  1. Install the front suspension member bracket LH with the 4 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



14. INSTALL FRONT SUSPENSION MEMBER BRACKET
  1. Install the front suspension member bracket with the 4 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



15. INSTALL PROPELLER SHAFT ASSEMBLY


    C098710E03
  1. Remove the SST from the extension housing.

    SST
    09325-40010  

  1. Install the propeller shaft assembly in the extension housing.



    C098711E02
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



16. INSTALL EXHAUST PIPE

HINT:
(Click here)



17. INSTALL OXYGEN SENSOR

HINT:
(Click here)



18. INSTALL NO.1 ENGINE UNDER COVER SUB-ASSEMBLY


19. INSTALL REAR ENGINE UNDER COVER ASSEMBLY


20. ADD AUTOMATIC TRANSMISSION FLUID

HINT:
(Click here)



21. INSPECT AUTOMATIC TRANSMISSION FLUID

HINT:
(Click here)



22. ADJUST SHIFT LEVER POSITION

HINT:
(Click here)



23. INSPECT SHIFT LEVER POSITION

HINT:
(Click here)



24. CHECK FOR EXHAUST GAS LEAKS

HINT:
(Click here)



25. RESET MEMORY

NOTICE:
Perform the RESET MEMORY (AT initialization) when replacing the automatic transmission assembly, engine assembly or ECM (Click here ).

HINT:
RESET MEMORY cannot be completed by only disconnecting the battery terminal.