ENGINE > ON-VEHICLE INSPECTION |
| 1. INSPECT ENGINE COOLANT |
The engine coolant should be between the LOW and FULL lines when the engine is cold.
If low, check for leakage and add Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology up to the FULL line.
| 2. INSPECT ENGINE OIL |
Warm up the engine, then stop the engine and wait for 5 minutes.
Check that the engine oil level is between the low level and full level marks on the level gauge.
If low, check for leakage and top oil up to the full level mark.
| 3. INSPECT BATTERY SPECIFIC GRAVITY |
![]() |
After having driven the vehicle and in the case that 20 minutes have not passed after having stopped the engine, turn the ignition switch ON and turn on the electrical system (headlight, blower motor, rear defogger etc.) for 60 seconds to remove the surface charge.
Turn the ignition switch OFF and turn off the electrical systems.
Measure the battery voltage between the negative (-) and positive (+) terminals of the battery.
![]() |
Check the indicator as shown in the illustration.
| 4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| 5. INSPECT FAN AND GENERATOR V BELT |
![]() |
Check that the indicator mark on the automatic tensioner is within the A range as shown in the illustration.
When the mark is out of the standard range, replace the V belt with a new one.
| 6. INSPECT V-RIBBED BELT TENSIONER ASSEMBLY |
Remove the V belt from the tensioner pulley. Then check that nothing gets caught the tensioner by turning it clockwise and counterclockwise.
When a malfunction exists, replace the tensioner.
| 7. WARM UP ENGINE |
| 8. INSPECT IGNITION TIMING |
![]() |
When using the intelligent tester or OBD II scan tool:
Connect the intelligent tester or OBD II scan tool to the DLC3.
Disconnect the intelligent tester or OBD II scan tool from the DLC3.
![]() |
When not using the intelligent tester or OBD II scan tool:
Remove the V-bank cover.
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
![]() |
Using SST, connect the tachometer probe to terminal TAC of the DLC3.
![]() |
Using SST, connect terminals TC and CG of the DLC3.
![]() |
Using the timing light, check the ignition timing.
Remove the SST from the DLC3.
Disconnect the timing light from the engine.
Install the V-bank cover.
| 9. INSPECT ENGINE IDLE SPEED |
![]() |
When using the intelligent tester or OBD II scan tool:
Connect the intelligent tester or OBD II scan tool to the DLC3.
Run the engine at 2,500 rpm for approx. 90 seconds.
Check the idle speed.
Disconnect the intelligent tester or OBD II scan tool from the DLC3.
![]() |
When not using the intelligent tester or OBD II scan tool:
Using SST, connect the tachometer probe to terminal TAC of the DLC3.
Run the engine at 2,500 rpm for approx. 90 seconds.
Check the idle speed.
Remove the SST from the DLC3.
Disconnect the tachometer from the DLC3.
| 10. INSPECT COMPRESSION |
Remove the V-bank cover sub-assembly.
Remove the air cleaner hose assembly.
Disconnect the throttle control motor connector.
Remove the 8 ignition coils.
Remove the 8 spark plugs.
Disconnect the 8 injector connectors.
![]() |
Inspect the cylinder compression pressure.
Insert a compression gauge into the spark plug hole (Procedure "A").
Fully open the throttle forcibly by hand.
While cranking the engine, measure the compression pressure (Procedure "B").
Repeat procedures "A" to "B" for each cylinder.
If the cylinder compression in one or more cylinders is low, pour a small amount of engine oil into the cylinder through the spark plug hole and repeat procedures "A" to "B" for the cylinders with low compression.
Connect the 8 injector connectors.
Install the 8 spark plugs.
Install the 8 ignition coils.
Connect the throttle control motor connector.
Install the air cleaner hose assembly.
Install the V-bank cover sub-assembly.
| 11. INSPECT CO/HC |
Start the engine.
Sustain the engine speed at 2,500 rpm for approx. 180 seconds.
![]() |
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe during idling.
Immediately check CO/HC concentration at idle and/or 2,500 rpm.
Check the heated oxygen sensor operation (Click here and Click here).
See the table below for possible causes, then inspect and correct the applicable causes if necessary.
| CO | HC | Symptom | Cause |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle Black smoke from exhaust) |
|