Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › 2009.08–2016.12
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch to the park/neutral position switch and also flows to terminal STA of the ECM (STA Signal).

WIRING DIAGRAM

A227113E06
1.833,1.448 2.146,1.615 0.313,0.167 10 false ST1 1.833,2.177 2.146,2.344 0.313,0.167 10 false ST2 1.344,1.448 1.656,1.615 0.313,0.167 10 false AM1 0.271,2.333 0.583,2.5 0.313,0.167 10 false AM1 1.344,2.177 1.656,2.344 0.313,0.167 10 false AM2 2.156,1.219 2.281,1.396 0.125,0.177 10 false 1 2.156,1.958 2.281,2.135 0.125,0.177 10 false 8 1.167,1.219 1.292,1.396 0.125,0.177 10 false 2 1.167,1.958 1.292,2.135 0.125,0.177 10 false 7 1.219,2.49 1.49,2.635 0.271,0.146 10 false F15 1.219,2.635 2.208,2.833 0.99,0.198 10 false Ignition Switch 5.844,1.125 5.969,1.271 0.125,0.146 10 false 2 5.146,1.76 5.271,1.906 0.125,0.146 10 false 4 4.896,2.573 5.021,2.719 0.125,0.146 10 false 5 5.76,1.344 6.042,1.5 0.281,0.156 10 false B37 6.104,1.302 6.479,1.458 0.375,0.156 10 false NSW 5.083,2.573 5.375,2.729 0.292,0.156 10 false B42 5.083,2.719 6.063,3.208 0.979,0.49 10 false Park/Neutral Position Switch Assembly 0.958,3.198 1.167,3.354 0.208,0.156 10 false ST 3.698,4.469 3.906,4.625 0.208,0.156 10 false ST 1.156,4.25 1.281,4.417 0.125,0.167 10 false 1 1.99,4.146 2.115,4.313 0.125,0.167 10 false 1 1.115,4.458 1.333,4.625 0.219,0.167 10 false C3 2.188,4.177 2.406,4.333 0.219,0.156 10 false C4 1.063,5.813 1.542,6 0.479,0.188 10 false Battery 1.542,5.25 2.656,5.417 1.115,0.167 10 false Starter Assembly 3.344,3.635 3.469,3.781 0.125,0.146 10 false 3 4.125,3.635 4.25,3.781 0.125,0.146 10 false 5 3.344,4.063 3.469,4.208 0.125,0.146 10 false 2 4.125,4.063 4.25,4.208 0.125,0.146 10 false 1 5.802,3.969 5.99,4.125 0.188,0.156 10 false 10 5.771,4.177 6.052,4.344 0.281,0.167 10 false F50 6.104,4.167 6.396,4.313 0.292,0.146 10 false STA 6.292,4.604 6.635,4.771 0.344,0.167 10 false ECM 0.281,3.854 0.646,4.042 0.365,0.188 12 false ALT

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

This chart is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Read the value.

OK:
Ignition Switch Position Starter Signal
ON Close
START Open




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK STARTER RELAY (ST) (POWER SOURCE)
2.CHECK STARTER RELAY (ST) (POWER SOURCE)
a.
A227799E01
1.405,0.527 1.566,0.688 0.161,0.161 10 *1 1.629,3.077 1.789,3.237 0.161,0.161 10 *2

Remove the starter relay (ST) from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 1 - Body ground Engine cranking 11 to 14 V


HINT:

The engine does not crank because the relay is not installed.


Text in Illustration
*1 Starter Relay (ST)
*2 Engine Room Relay Block


c.

Reinstall the starter relay (ST).



OK

3.INSPECT STARTER RELAY (ST)

NG

5.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.INSPECT STARTER RELAY (ST)
a.

Inspect the starter relay (ST) (See page Engine / Hybrid System>1GR-FE STARTING>RELAY>ON-VEHICLE INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - BODY GROUND)

NG

REPLACE STARTER RELAY (ST)

4.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - BODY GROUND)
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 2 - Body ground Always Below 1 Ω



c.

Reinstall the starter relay (ST).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY (ST) - BODY GROUND)

5.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 1 - B42-5 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 1 or B42-5 - Body ground Always 10 kΩ or higher



d.

Reinstall the starter relay (ST).


e.

Reconnect the park/neutral position switch assembly connector.



OK

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly for 4WD (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION).


b.

Inspect the park/neutral position switch assembly for 2WD (See page Drivetrain>A750E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ignition switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
B42-4 - F15-1 (ST1) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
B42-4 or F15-1 (ST1) - Body ground Always 10 kΩ or higher



d.

Reconnect the park/neutral position switch assembly connector.


e.

Reconnect the ignition switch assembly connector.



OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1GR-FE STARTING>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMBLY