Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0115  Engine Coolant Temperature Circuit Malfunction  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor.

The structure of the sensor and its connection to the ECM are the same as those of the intake air temperature sensor.

HINT:

When DTC P0115, P0117 or P0118 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. The ECM continues operating in fail-safe mode until a pass condition is detected.


DTC No. DTC Detection Condition Trouble Area
P0115 Open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


P0117 Short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


P0118 Open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM



HINT:

When any of these DTCs are stored, check the ECT by entering the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit

MONITOR DESCRIPTION

The engine coolant temperature sensor is used to monitor the engine coolant temperature. The engine coolant temperature sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are reflected in the output voltage from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the ECT. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the engine coolant temperature sensor and stores a DTC.

Example:

If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the engine coolant temperature sensor circuit and stores DTC P0118. Conversely, if the voltage output is below 0.14 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit and stores DTC P0117.

If the malfunction is not repaired successfully, a DTC is stored 0.5 seconds after the engine is next started.

WIRING DIAGRAM

A227102E08
2.448,0.604 2.583,0.75 0.135,0.146 10 false 2 5.229,0.531 5.417,0.677 0.188,0.146 10 false 17 5.271,1.146 5.417,1.292 0.146,0.146 10 false 8 2.448,1.219 2.573,1.375 0.125,0.156 10 false 1 0.479,2.125 2.802,2.292 2.323,0.167 10 false Engine Coolant Temperature Sensor 0.479,1.917 0.792,2.063 0.313,0.146 10 false B25 6,2.292 6.344,2.469 0.344,0.177 10 false ECM 5.177,1.344 5.469,1.531 0.292,0.188 10 false B37 5.177,0.729 5.49,0.885 0.313,0.156 10 false B38 5.521,0.813 5.906,0.958 0.385,0.146 10 false THW 5.531,1.438 5.99,1.604 0.458,0.167 10 false ETHW 5.74,0.24 5.99,0.385 0.25,0.146 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


d.

Read DTCs.

Result
Display (DTC Output) Proceed to
P0115 A
P0117 B
P0118 C



A

2.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)

B

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
2.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


e.

Read the value displayed on the intelligent tester.

Standard value:

Between 80°C and 100°C (167°F and 212°F) with warm engine


Result
Temperature Displayed Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
Between 80°C and 100°C (176°F and 212°F) C

HINT:
·

If there is an open circuit, the intelligent tester indicates -40°C (-40°F).


·

If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.





A

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
U149586E03
0.823,0.177 1.01,0.333 0.188,0.156 10 false *1 0.24,1.875 0.427,2.031 0.188,0.156 10 false *a 2.594,0.177 2.781,0.333 0.188,0.156 10 false *2 2.458,1.01 2.813,1.167 0.354,0.156 10 false THW 2.438,1.458 2.875,1.615 0.438,0.156 10 false ETHW 0.771,2.76 1.094,2.938 0.323,0.177 10 false B25

a.

Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


g.

Read the value displayed on the intelligent tester.

Standard value:

140°C (284°F) or higher


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)


h.

Reconnect the engine coolant temperature sensor connector.



OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B25-2 - B38-17 (THW) Always Below 1 Ω
B25-1 - B37-8 (ETHW) Always Below 1 Ω



d.

Reconnect the engine coolant temperature sensor connector.


e.

Reconnect the ECM connector.



OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
A211723E15
0.698,0.125 0.906,0.302 0.208,0.177 10 false *1 2.542,0.125 2.75,0.302 0.208,0.177 10 false *2 2.458,1.042 2.979,1.219 0.521,0.177 10 false THW 2.458,1.448 2.979,1.625 0.521,0.177 10 false ETHW

a.

Disconnect the engine coolant temperature sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


f.

Read the value displayed on the intelligent tester.

Standard value:

-40°C (-40°F)


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM


g.

Reconnect the engine coolant temperature sensor connector.



OK

NG

6.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
6.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B25-2 or B38-17 (THW) - Body ground Always 10 kΩ or higher



d.

Reconnect the engine coolant temperature sensor connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR