Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio.

Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM according to the engine speed and throttle valve position. The ECM continues operating in fail-safe mode until a pass condition is detected.


A202104E01
0.117,0.354 1.324,0.510 1.207,0.156 10 (Thermistor) 0.099,0.205 1.491,0.398 1.392,0.193 10 Temperature Sensor 1.416,0.284 1.542,0.284 1.542,0.284 1.954,1.495 false 2.695,0.887 4.434,1.061 1.739,0.174 10 Platinum Hot Wire (Heater) 2.294,1.469 2.63,0.957 false 2.228,0.564 3.333,0.720 1.105,0.156 10 Power Transistor 2.887,1.578 3.846,1.750 0.959,0.172 10 Output Voltage 3.078,2.213 4.817,2.387 1.739,0.174 10 Platinum Hot Wire (Heater) 4.847,1.307 4.447,2.176 false 5.12,1.543 5.586,2.134 false 1.654,1.511 1.800,1.667 0.147,0.156 10 A 2.48,1.512 2.627,1.682 0.147,0.170 10 B 5.245,2.302 6.452,2.458 1.207,0.156 10 (Thermistor) 5.226,2.152 6.618,2.345 1.392,0.193 10 Temperature Sensor

DTC No. DTC Detection Condition Trouble Area
P0102 Mass air flow meter voltage is below 0.2 V for 3 seconds
(1 trip detection logic: Engine speed is less than 4000 rpm)
(2 trip detection logic: Engine speed is 4000 rpm or more).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


P0103 Mass air flow meter voltage is higher than 4.9 V for 3 seconds
(1 trip detection logic: Engine speed is less than 4000 rpm)
(2 trip detection logic: Engine speed is 4000 rpm or more).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM



HINT:

When any of these DTCs are stored, check the air-flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Mass Air Flow Rate (g/sec.) Malfunction
Approximately 0.0
·

Open in mass air flow meter power source circuit

·

Open or short in VG circuit


271.0 or more
·

Open in E2G circuit




MONITOR DESCRIPTION

If there is a defect in the mass air flow meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter and stores a DTC.

Example:

When the sensor output voltage remains below 0.2 V, or higher than 4.9 V, for more than 3 seconds, the ECM stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

WIRING DIAGRAM

A227124E01
0.606,2.684 1.105,2.867 0.498,0.184 10 Battery 1.223,0.75 1.481,0.915 0.258,0.165 10 EFI 0.457,1.824 0.826,1.990 0.369,0.165 10 P/I-B 0.691,0.595 0.902,0.750 0.211,0.156 10 1E 0.737,0.407 0.856,0.591 0.119,0.184 10 1 2.549,0.588 2.761,0.744 0.211,0.156 10 1D 2.596,0.401 2.715,0.585 0.119,0.184 10 4 2.537,0.973 2.749,1.129 0.211,0.156 10 1D 2.584,0.786 2.703,0.969 0.119,0.184 10 2 1.317,1.39 1.529,1.546 0.211,0.156 10 1D 1.106,1.384 1.225,1.568 0.119,0.184 10 3 1.699,1.329 2.346,1.504 0.647,0.174 10 EFI MAIN 1.498,1.61 2.960,1.803 1.461,0.193 10 No. 1 Integration Relay 2.885,0.732 3.523,0.906 0.637,0.174 10 EFI No. 2 3.497,0.493 3.635,0.668 0.137,0.174 10 3 4.982,0.83 5.120,1.004 0.137,0.174 10 5 4.982,1.371 5.120,1.546 0.137,0.174 10 4 3.67,0.479 3.891,0.645 0.221,0.165 10 +B 4.688,0.844 4.927,1.009 0.239,0.165 10 VG 5.716,0.844 5.955,1.009 0.239,0.165 10 VG 4.604,1.376 4.927,1.541 0.323,0.165 10 E2G 5.716,1.376 6.038,1.541 0.323,0.165 10 E2G 3.623,1.918 3.918,2.083 0.295,0.165 10 B35 3.623,2.077 4.964,2.242 1.341,0.165 10 Mass Air Flow Meter 6.173,3.254 6.505,3.419 0.332,0.165 10 ECM 5.398,0.732 5.600,0.897 0.202,0.165 10 14 5.398,1.283 5.600,1.448 0.202,0.165 10 13 5.371,0.939 5.656,1.104 0.286,0.165 10 B37 5.371,1.49 5.656,1.655 0.286,0.165 10 B37 5.371,2.867 5.648,3.042 0.276,0.174 10 F51 5.44,2.67 5.559,2.844 0.119,0.174 10 9 5.706,2.768 6.149,2.933 0.443,0.165 10 MREL

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.


e.

Read the values displayed on the intelligent tester.

Result
Mass Air Flow Rate (g/sec.) Proceed to
0.0 A
271.0 or more B
Between 1.0 and 270.0*1 C

HINT:

*1: The value must change when the throttle valve is open or closed with the engine running.




A

2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)

B

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

C

2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
U149573E03
1.729,1.396 2.51,0.917 false 0.333,1.354 0.604,1.5 0.271,0.146 10 false B35 0.063,0.094 0.229,0.26 0.167,0.167 10 false *a 2.5,0.802 2.938,0.99 0.438,0.188 10 false +B (+)

a.

Disconnect the mass air flow meter connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B35-3 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Mass Air Flow Meter)


d.

Reconnect the mass air flow meter connector.



OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY (EFI MAIN))
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B35-5 (VG) - B37-14 (VG) Always Below 1 Ω
B35-4 (E2G) - B37-13 (E2G) Always Below 1 Ω
B35-5 (VG) or B37-14 (VG) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.



OK

4.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER

OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY (EFI MAIN))
a.

Disconnect the mass air flow meter connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B35-3 (+B) - 1D-4 Always Below 1 Ω
B35-3 (+B) or 1D-4 - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reinstall the No. 1 integration relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B35-4 (E2G) - Body ground Always Below 1 Ω




OK

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B35-5 (VG) - B37-14 (VG) Always Below 1 Ω
B35-4 (E2G) - B37-13 (E2G) Always Below 1 Ω
B35-5 (VG) or B37-14 (VG) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR