Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  P0355  Ignition Coil "E" Primary / Secondary Circuit  P0356  Ignition Coil "F" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the No. 1 ignition coil circuit.

·

If DTC P0352 is output, check the No. 2 ignition coil circuit.

·

If DTC P0353 is output, check the No. 3 ignition coil circuit.

·

If DTC P0354 is output, check the No. 4 ignition coil circuit.

·

If DTC P0355 is output, check the No. 5 ignition coil circuit.

·

If DTC P0356 is output, check the No. 6 ignition coil circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A228076E02
3.026,8.01 3.376,8.175 0.350,0.165 10 ECM 0.333,2.159 2.053,2.324 1.721,0.165 10 Crankshaft Position Sensor 0.766,4.217 1.561,4.383 0.795,0.165 10 VVT Sensor 0.261,5.637 2.149,6.376 1.887,0.739 10 Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 3.182,1.517 3.570,1.700 0.387,0.184 10 IGT1 3.182,1.946 3.570,2.130 0.387,0.184 10 IGF1 3.182,2.899 3.570,3.083 0.387,0.184 10 IGT2 3.182,3.964 3.570,4.147 0.387,0.184 10 IGT3 3.182,5.066 3.570,5.250 0.387,0.184 10 IGT4 3.182,6.143 3.570,6.326 0.387,0.184 10 IGT5 3.182,7.233 3.570,7.417 0.387,0.184 10 IGT6 4.222,0.864 5.091,1.066 0.869,0.202 10 from Battery 5.744,1.175 6.877,1.370 1.133,0.195 10 No. 1 Ignition Coil 4.455,3.003 5.588,3.164 1.133,0.161 10 No. 2 Ignition Coil 4.455,4.096 5.588,4.256 1.133,0.161 10 No. 3 Ignition Coil 4.455,5.189 5.588,5.349 1.133,0.161 10 No. 4 Ignition Coil 4.455,6.255 5.588,6.415 1.133,0.161 10 No. 5 Ignition Coil 4.455,7.337 5.588,7.497 1.133,0.161 10 No. 6 Ignition Coil 5.726,2.045 6.805,2.240 1.079,0.196 10 No. 1 Spark Plug 5.726,3.278 6.805,3.473 1.079,0.196 10 No. 2 Spark Plug 5.726,4.361 6.805,4.557 1.079,0.196 10 No. 3 Spark Plug 5.726,5.445 6.805,5.640 1.079,0.196 10 No. 4 Spark Plug 5.726,6.528 6.805,6.724 1.079,0.196 10 No. 5 Spark Plug 5.726,7.611 6.805,7.807 1.079,0.196 10 No. 6 Spark Plug

DTC No. DTC Detection Condition Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT circuit (1 to 6) between ignition coil and ECM

·

No. 1 to No. 6 ignition coil

·

ECM



A388710E01
0.25,0.604 0.583,0.802 0.333,0.198 10 false IGT 0.271,1.427 0.604,1.625 0.333,0.198 10 false IGF 2.927,1.875 3.26,2.073 0.333,0.198 10 false GND 2.948,1.021 3.281,1.219 0.333,0.198 10 false GND 2.75,0.313 3.375,0.5 0.625,0.188 10 false 2 V/DIV. 1.344,1.99 2.417,2.177 1.073,0.188 10 false 20 msec./DIV.


Reference: Inspection using an oscilloscope.

While cranking or idling the engine, check the waveform between terminals IGT (1 to 6) and E1, and IGF1 and E1 of the ECM connector.

Item Content
Terminal CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6 - E1
CH2: IGF1 - E1
Equipment Setting 2 V/DIV.
20 msec./DIV.
Condition Cranking or idling


MONITOR DESCRIPTION

A115898E02
4.232,0.793 6.034,0.976 1.802,0.184 10 Ignition Coil with Igniter 4.099,1.568 4.762,1.752 0.663,0.184 10 Igniter 5.311,1.393 6.259,1.556 0.948,0.163 10 Ignition Coil 0.305,2.928 1.439,3.292 1.134,0.364 10 Ignition Signal (IGT) 0.312,3.65 1.365,4.173 1.053,0.523 10 Ignition Confirmation Signal (IGF) 1.592,3.537 2.150,3.714 0.559,0.177 10 Normal 1.367,3.923 2.148,4.099 0.781,0.177 10 Malfunction 3.483,4.546 4.430,4.733 0.948,0.187 10 Circuit Open 5.806,5.011 6.330,5.174 0.524,0.163 10 Time 1.786,1.695 2.185,1.870 0.398,0.175 10 ECM 2.9,1.363 3.226,1.549 0.326,0.186 10 IGT 2.9,1.777 3.226,1.963 0.326,0.186 10 IGF

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

WIRING DIAGRAM

A227109E01
0.422,0.933 0.545,1.099 0.123,0.165 10 A 3.253,0.821 3.418,1.017 0.165,0.195 10 1 3.246,1.221 3.369,1.372 0.123,0.151 10 4 4.405,0.835 4.519,0.987 0.114,0.151 10 3 4.413,1.212 4.537,1.377 0.123,0.165 10 2 3.439,0.943 3.639,1.089 0.200,0.147 10 +B 3.43,1.316 3.778,1.454 0.348,0.137 10 GND 4.006,0.943 4.338,1.089 0.332,0.147 10 IGT1 4.077,1.316 4.349,1.458 0.272,0.142 10 IGF 3.022,1.618 4.812,1.811 1.790,0.193 10 No. 1 Ignition Coil Assembly 3.241,2.047 3.406,2.243 0.165,0.195 10 1 3.234,2.447 3.357,2.598 0.123,0.151 10 4 4.393,2.061 4.507,2.213 0.114,0.151 10 3 4.401,2.438 4.525,2.603 0.123,0.165 10 2 3.439,2.169 3.639,2.315 0.200,0.147 10 +B 3.43,2.57 3.778,2.708 0.348,0.137 10 GND 4.006,2.169 4.338,2.315 0.332,0.147 10 IGT2 4.077,2.57 4.348,2.712 0.272,0.142 10 IGF 2.994,2.865 4.784,3.058 1.790,0.193 10 No. 2 Ignition Coil Assembly 3.252,3.336 3.418,3.532 0.165,0.195 10 1 3.245,3.736 3.369,3.887 0.123,0.151 10 4 4.405,3.35 4.519,3.502 0.114,0.151 10 3 4.413,3.727 4.536,3.892 0.123,0.165 10 2 3.435,3.458 3.635,3.604 0.200,0.147 10 +B 3.426,3.831 3.774,3.969 0.348,0.137 10 GND 4.002,3.458 4.334,3.604 0.332,0.147 10 IGT3 4.073,3.831 4.344,3.973 0.272,0.142 10 IGF 2.994,4.133 4.784,4.326 1.790,0.193 10 No. 3 Ignition Coil Assembly 3.442,4.59 3.607,4.786 0.165,0.195 10 1 3.435,4.99 3.558,5.141 0.123,0.151 10 4 4.594,4.604 4.708,4.755 0.114,0.151 10 3 4.602,4.981 4.726,5.146 0.123,0.165 10 2 3.632,4.712 3.832,4.858 0.200,0.147 10 +B 3.623,5.085 3.971,5.223 0.348,0.137 10 GND 4.199,4.712 4.531,4.858 0.332,0.147 10 IGT4 4.27,5.085 4.541,5.227 0.272,0.142 10 IGF 3.183,5.387 4.973,5.580 1.790,0.193 10 No. 4 Ignition Coil Assembly 3.446,5.851 3.611,6.047 0.165,0.195 10 1 3.439,6.25 3.562,6.402 0.123,0.151 10 4 4.598,5.865 4.712,6.016 0.114,0.151 10 3 4.606,6.242 4.730,6.407 0.123,0.165 10 2 3.636,5.973 3.836,6.119 0.200,0.147 10 +B 3.627,6.346 3.975,6.484 0.348,0.137 10 GND 4.203,5.973 4.535,6.119 0.332,0.147 10 IGT5 4.274,6.346 4.545,6.488 0.272,0.142 10 IGF 3.183,6.648 4.973,6.841 1.790,0.193 10 No. 5 Ignition Coil Assembly 3.438,7.098 3.603,7.294 0.165,0.195 10 1 3.431,7.497 3.554,7.649 0.123,0.151 10 4 4.594,7.112 4.708,7.263 0.114,0.151 10 3 4.602,7.489 4.726,7.654 0.123,0.165 10 2 3.632,7.22 3.832,7.366 0.200,0.147 10 +B 3.623,7.593 3.971,7.730 0.348,0.137 10 GND 4.199,7.22 4.531,7.366 0.332,0.147 10 IGT6 4.27,7.593 4.541,7.735 0.272,0.142 10 IGF 3.183,7.895 4.973,8.088 1.790,0.193 10 No. 6 Ignition Coil Assembly 5.596,0.944 5.891,1.109 0.295,0.165 10 B38 5.596,2.198 5.891,2.363 0.295,0.165 10 B38 5.596,3.452 5.891,3.617 0.295,0.165 10 B38 5.6,4.714 5.895,4.879 0.295,0.165 10 B38 5.6,5.092 5.895,5.257 0.295,0.165 10 B38 5.596,5.96 5.891,6.125 0.295,0.165 10 B38 5.596,7.218 5.891,7.383 0.295,0.165 10 B37 5.92,1.068 6.264,1.224 0.343,0.156 10 IGT1 5.92,2.329 6.264,2.485 0.343,0.156 10 IGT2 5.92,3.59 6.264,3.746 0.343,0.156 10 IGT3 5.92,4.851 6.264,5.006 0.343,0.156 10 IGT4 5.92,5.173 6.264,5.329 0.343,0.156 10 IGF1 5.92,6.112 6.264,6.267 0.343,0.156 10 IGT5 5.92,7.372 6.264,7.528 0.343,0.156 10 IGT6 5.636,0.753 5.827,0.922 0.191,0.170 10 24 5.636,2.013 5.827,2.183 0.191,0.170 10 25 5.636,3.274 5.827,3.444 0.191,0.170 10 26 5.636,4.535 5.827,4.705 0.191,0.170 10 27 5.686,4.907 5.827,5.076 0.142,0.170 10 6 5.636,5.796 5.827,5.966 0.191,0.170 10 28 5.636,7.057 5.827,7.227 0.191,0.170 10 25 6.288,8.161 6.632,8.316 0.343,0.156 10 ECM 3.022,1.464 3.247,1.619 0.225,0.156 10 B7 2.994,2.703 3.219,2.859 0.225,0.156 10 B8 2.994,3.978 3.219,4.134 0.225,0.156 10 B9 3.183,5.225 3.466,5.381 0.283,0.156 10 B10 3.183,6.493 3.466,6.649 0.283,0.156 10 B11 3.183,7.733 3.473,7.889 0.290,0.156 10 B12

A227129E02
6.427,0.531 6.552,0.698 0.125,0.167 10 false A 5.021,0.677 5.271,0.854 0.25,0.177 10 false INJ 4.375,0.531 4.615,0.698 0.24,0.167 10 false 1C 4.385,0.979 4.625,1.146 0.24,0.167 10 false 1C 1.802,0.979 2.042,1.146 0.24,0.167 10 false 1C 1.813,0.531 2.052,0.698 0.24,0.167 10 false 1E 3.406,1.333 3.677,1.49 0.271,0.156 10 false IG2 2.396,0.656 2.667,0.813 0.271,0.156 10 false IG2 4.698,2.281 4.969,2.438 0.271,0.156 10 false IG2 4.438,0.292 4.563,0.458 0.125,0.167 10 false 5 1.854,0.292 1.979,0.458 0.125,0.167 10 false 1 4.438,0.75 4.563,0.917 0.125,0.167 10 false 1 1.854,0.75 1.979,0.917 0.125,0.167 10 false 3 0.583,1.26 0.948,1.417 0.365,0.156 10 false P/I-B 1.969,2.281 2.188,2.448 0.219,0.167 10 false ST 0.698,2.927 1.188,3.125 0.49,0.198 10 false Battery 2.448,1.615 3.917,1.813 1.469,0.198 10 false No. 1 Integration Relay 4.125,2.708 4.427,2.875 0.302,0.167 10 false F15 4.135,2.885 5.208,3.083 1.073,0.198 10 false Ignition Switch 4.198,2.281 4.531,2.458 0.333,0.177 10 false AM2 4.042,2.01 4.156,2.188 0.115,0.177 10 false 7 5.021,2.01 5.135,2.188 0.115,0.177 10 false 6

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
U149580E03
1.26,1.167 0.979,1.74 false 2.177,1.177 2.385,1.729 false 0.177,0.698 0.396,0.865 0.219,0.167 10 false B7 0.594,0.708 0.813,0.875 0.219,0.167 10 false B8 0.177,1.021 0.396,1.188 0.219,0.167 10 false B9 0.583,1.01 0.896,1.177 0.313,0.167 10 false B10 0.125,1.333 0.427,1.5 0.302,0.167 10 false B11 0.583,1.333 0.875,1.5 0.292,0.167 10 false B12 0.083,0.115 0.271,0.302 0.188,0.188 10 false *a 0.802,1.75 1.219,1.938 0.417,0.188 10 false +B (+) 2.167,1.771 2.719,1.948 0.552,0.177 10 false GND (-)

a.

Disconnect the ignition coil assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B7-4 (GND) - Body ground Always Below 1 Ω
B8-4 (GND) - Body ground Always Below 1 Ω
B9-4 (GND) - Body ground Always Below 1 Ω
B10-4 (GND) - Body ground Always Below 1 Ω
B11-4 (GND) - Body ground Always Below 1 Ω
B12-4 (GND) - Body ground Always Below 1 Ω



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B7-1 (+B) - B7-4 (GND) Ignition switch ON 11 to 14 V
B8-1 (+B) - B8-4 (GND) Ignition switch ON 11 to 14 V
B9-1 (+B) - B9-4 (GND) Ignition switch ON 11 to 14 V
B10-1 (+B) - B10-4 (GND) Ignition switch ON 11 to 14 V
B11-1 (+B) - B11-4 (GND) Ignition switch ON 11 to 14 V
B12-1 (+B) - B12-4 (GND) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Ignition Coil with Igniter)


e.

Reconnect the ignition coil assembly connector.



OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B7-2 (IGF) - B38-6 (IGF1) Always Below 1 Ω
B8-2 (IGF) - B38-6 (IGF1) Always Below 1 Ω
B9-2 (IGF) - B38-6 (IGF1) Always Below 1 Ω
B10-2 (IGF) - B38-6 (IGF1) Always Below 1 Ω
B11-2 (IGF) - B38-6 (IGF1) Always Below 1 Ω
B12-2 (IGF) - B38-6 (IGF1) Always Below 1 Ω
B7-3 (IGT1) - B38-24 (IGT1) Always Below 1 Ω
B8-3 (IGT2) - B38-25 (IGT2) Always Below 1 Ω
B9-3 (IGT3) - B38-26 (IGT3) Always Below 1 Ω
B10-3 (IGT4) - B38-27 (IGT4) Always Below 1 Ω
B11-3 (IGT5) - B38-28 (IGT5) Always Below 1 Ω
B12-3 (IGT6) - B37-25 (IGT6) Always Below 1 Ω
B7-2 (IGF) or B38-6 (IGF1) - Body ground Always 10 kΩ or higher
B8-2 (IGF) or B38-6 (IGF1) - Body ground Always 10 kΩ or higher
B9-2 (IGF) or B38-6 (IGF1) - Body ground Always 10 kΩ or higher
B10-2 (IGF) or B38-6 (IGF1) - Body ground Always 10 kΩ or higher
B11-2 (IGF) or B38-6 (IGF1) - Body ground Always 10 kΩ or higher
B12-2 (IGF) or B38-6 (IGF1) - Body ground Always 10 kΩ or higher
B7-3 (IGT1) or B38-24 (IGT1) - Body ground Always 10 kΩ or higher
B8-3 (IGT2) or B38-25 (IGT2) - Body ground Always 10 kΩ or higher
B9-3 (IGT3) or B38-26 (IGT3) - Body ground Always 10 kΩ or higher
B10-3 (IGT4) or B38-27 (IGT4) - Body ground Always 10 kΩ or higher
B11-3 (IGT5) or B38-28 (IGT5) - Body ground Always 10 kΩ or higher
B12-3 (IGT6) or B37-25 (IGT6) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the ignition coil assembly connector.



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.



d.

Shuffle the arrangement of the ignition coil assemblies (among the No. 1 to No. 6 cylinders).

NOTICE:

Do not shuffle the connectors.



e.

Perform a simulation test.


f.

Check the DTCs output on the intelligent tester.

Result
Display (DTC Output) Proceed to
Same DTC output A
Different ignition coil DTC output B



A

B