Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2014.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0452  Evaporative Emission Control System Pressure Sensor / Switch Low Input  P0453  Evaporative Emission Control System Pressure Sensor / Switch High Input  


DESCRIPTION

DTC Monitoring Item Malfunction Detection Condition Trouble Area Detection Timing Detection Logic
P0452 Canister pressure sensor low input EVAP pressure is below 42.1 kPa for 0.5 seconds.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


·

Ignition switch ON

·

EVAP monitoring (ignition switch off)


1 trip
P0453 Canister pressure sensor high input EVAP pressure is higher than 123.8 kPa for 0.5 seconds.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


·

Ignition switch ON

·

EVAP monitoring (ignition switch off)


1 trip

HINT:

The canister pressure sensor is built into the canister pump module.


MONITOR DESCRIPTION

A388727E01
4.531,1.458 4.948,1.042 false 4.521,3.333 4.938,2.917 false 0.219,0.125 2.792,0.333 2.573,0.208 10 false Canister Pressure Sensor Specification: 1.302,0.927 2.385,1.167 1.083,0.24 10 false Output Voltage 4.99,0.885 6.146,1.135 1.156,0.25 10 false Malfunction Area 1.708,1.438 2.313,1.646 0.604,0.208 10 false 4.900 V 1.719,1.885 2.323,2.094 0.604,0.208 10 false 4.150 V 1.698,2.594 2.302,2.802 0.604,0.208 10 false 1.425 V 1.719,3.01 2.323,3.219 0.604,0.208 10 false 0.450 V 2.792,3.469 3,3.698 0.208,0.229 10 false 60 4.385,3.458 4.854,3.698 0.469,0.24 10 false kPa-a 3.531,3.458 3.844,3.688 0.313,0.229 10 false 110 2.771,3.646 3.135,3.885 0.365,0.24 10 false (450) 3.531,3.635 3.896,3.875 0.365,0.24 10 false (825) 4.365,3.625 5.01,3.885 0.646,0.26 10 false (mmHg-a) 5,2.833 6.156,3.083 1.156,0.25 10 false Malfunction Area 3.927,2.167 4.896,2.406 0.969,0.24 10 false Usable Range 5.156,3.208 5.927,3.417 0.771,0.208 10 false Pressure 1.99,4.104 2.417,4.313 0.427,0.208 10 false HINT: 2,4.375 5.875,4.583 3.875,0.208 10 false Standard atmospheric pressure is 101.3 kPa-a (760 mmHg-a)

1.

DTC P0452: Canister pressure sensor voltage is low

If the canister pressure sensor output [pressure] is below 42.1 kPa-a (315.9 mmHg-a), the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).

2.

DTC P0453: Canister pressure sensor voltage is high

If the canister pressure sensor output [pressure] is 123.8 kPa-a (928.4 mmHg-a) or higher, the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).


CONFIRMATION DRIVING PATTERN

A199236E31
0.079,1.247 1.360,1.500 1.281,0.253 10 Ignition Switch ON 3.455,2.359 5.083,2.536 1.628,0.177 10 Approximately 23 minutes 2.76,2.91 2.971,3.131 0.211,0.221 10 [A] 5.398,2.923 5.631,3.116 0.233,0.193 10 [B]

NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 5 steps performed automatically by the GTS. It takes a maximum of approximately 23 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).



1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on [A].

7.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

8.

After the "Evaporative System Check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All readiness.

9.

Input the DTC: P0452 or P0453.

10.

Check the DTC judgment result [B].

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A334802E02
1.427,6.76 1.906,6.948 0.479,0.188 10 false Battery 1.385,6.135 1.719,6.292 0.333,0.156 10 false P/I-B 1.156,5.156 1.792,5.313 0.635,0.156 10 false EFI NO. 2 3.094,6.938 4.573,7.26 1.479,0.323 10 false NO. 1 Integration Relay 3.677,6.625 4.323,6.771 0.646,0.146 10 false EFI MAIN 3.188,6.094 3.438,6.25 0.25,0.156 10 false EFI 2.75,5.771 2.865,5.938 0.115,0.167 10 false 1 3.781,4.552 3.896,4.719 0.115,0.167 10 false 1 4.542,4.563 4.656,4.729 0.115,0.167 10 false 2 2.698,5.948 2.906,6.104 0.208,0.156 10 false 1E 4.573,5.74 4.688,5.906 0.115,0.167 10 false 4 4.521,5.927 4.729,6.083 0.208,0.156 10 false 1D 4.573,6.135 4.688,6.302 0.115,0.167 10 false 2 4.531,6.302 4.74,6.458 0.208,0.156 10 false 1D 2.75,6.125 2.865,6.292 0.115,0.167 10 false 3 2.698,6.302 2.906,6.458 0.208,0.156 10 false 1D 5.073,6.302 5.344,6.469 0.271,0.167 10 false F51 5.146,6.125 5.271,6.292 0.125,0.167 10 false 9 5.396,6.219 5.823,6.385 0.427,0.167 10 false MREL 5.063,0.635 5.333,0.802 0.271,0.167 10 false F50 5.156,0.448 5.281,0.615 0.125,0.167 10 false 7 5.396,0.635 5.885,0.844 0.49,0.208 10 false MPMP 5.073,2.167 5.344,2.333 0.271,0.167 10 false B37 5.135,1.99 5.26,2.156 0.125,0.167 10 false 1 5.396,2.052 5.854,2.219 0.458,0.167 10 false PPMP 5.073,1.708 5.344,1.875 0.271,0.167 10 false B36 5.115,1.51 5.313,1.677 0.198,0.167 10 false 15 5.396,1.583 5.854,1.75 0.458,0.167 10 false VCV1 5.073,4.656 5.344,4.823 0.271,0.167 10 false B38 5.104,4.469 5.302,4.635 0.198,0.167 10 false 18 5.406,4.667 5.76,4.833 0.354,0.167 10 false PRG 5.063,3.302 5.333,3.469 0.271,0.167 10 false F50 5.104,3.115 5.302,3.281 0.198,0.167 10 false 19 5.417,3.292 5.854,3.458 0.438,0.167 10 false VPMP 5.063,2.646 5.375,2.875 0.313,0.229 10 false B37 5.167,2.448 5.292,2.615 0.125,0.167 10 false 8 5.385,2.51 5.844,2.677 0.458,0.167 10 false ETHW 3.854,4.969 4.146,5.115 0.292,0.146 10 false B15 3.865,5.135 4.594,5.323 0.729,0.188 10 false Purge VSV 5.885,6.99 6.24,7.146 0.354,0.156 10 false ECM 1.667,0.885 3.042,1.073 1.375,0.188 10 false Leak Detection Pump 1.625,3.875 1.927,4.021 0.302,0.146 10 false O21 1.635,4.052 3.135,4.229 1.5,0.177 10 false Canister Pump Module 2.031,3.458 2.729,3.625 0.698,0.167 10 false Vent Valve 1.563,1.74 2.167,2.24 0.604,0.5 10 false Canister Pressure Sensor 1.24,3.177 1.365,3.344 0.125,0.167 10 false 5 3.323,3.188 3.448,3.354 0.125,0.167 10 false 1 3.323,2.531 3.448,2.698 0.125,0.167 10 false 8 3.323,2.052 3.448,2.219 0.125,0.167 10 false 7 3.323,1.594 3.448,1.76 0.125,0.167 10 false 6 1.427,3.188 1.833,3.365 0.406,0.177 10 false VLVB 2.854,3.219 3.292,3.365 0.438,0.146 10 false VGND 2.844,2.74 3.281,2.885 0.438,0.146 10 false SGND 2.885,2.052 3.323,2.198 0.438,0.146 10 false VOUT 2.948,1.604 3.292,1.75 0.344,0.146 10 false VCC 1.229,0.542 1.354,0.708 0.125,0.167 10 false 4 3.323,0.521 3.448,0.688 0.125,0.167 10 false 3 1.417,0.531 1.875,0.677 0.458,0.146 10 false MGND 2.854,0.542 3.292,0.719 0.438,0.177 10 false MTRB

CAUTION / NOTICE / HINT

NOTICE:
·

When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel tank cap assembly.

·

Do not disassemble the canister pump module.

·

The GTS is required to conduct the following diagnostic troubleshooting procedure.



PROCEDURE

1.CONFIRM DTC AND EVAP PRESSURE
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON (do not start the engine).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


e.

Read DTCs.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump.


g.

Read the EVAP (Evaporative Emission) pressure displayed on the GTS.

Result
Display (DTC Output) Test Result Suspected Trouble Area Proceed to
P0452 Below 45 kPa-a (337.3 mmHg-a)
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Canister pressure sensor

·

Short in ECM circuit


A
P0453 Higher than 120 kPa-a (900 mmHg-a)
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Canister pressure sensor

·

Open in ECM circuit


B



A

2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Test Result Suspected Trouble Area Proceed to
B37-1 (PPMP) - Body ground Always 10 Ω or less
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Short in canister pressure sensor circuit


A
10 kΩ or higher
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Short in ECM circuit


B


d.

Reconnect the ECM connector.



A

3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

7.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the canister pump module connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Test Result Suspected Trouble Area Proceed to
B37-1 (PPMP) - Body ground Always 10 kΩ or higher Short in canister pressure sensor circuit A
10 Ω or less Short in wire harness/connector (ECM - Canister pressure sensor) B


d.

Reconnect the canister pump module connector.


e.

Reconnect the ECM connector.



A

5.REPLACE CANISTER ASSEMBLY

B

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the canister pump module connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O21-8 (SGND) - Body ground Always 100 Ω or less



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O21-6 (VCC) - Body ground Ignition switch ON 4.5 to 5.5 V
O21-7 (VOUT) - Body ground Ignition switch ON 4.5 to 5.5 V


Result
Test Result Suspected Trouble Area Proceed to
Voltage and resistance within standard ranges Open in canister pressure sensor circuit A
Voltage and resistance outside standard ranges Open in wire harness/connector (ECM - Canister pressure sensor) B


e.

Reconnect the canister pump module connector.



A

5.REPLACE CANISTER ASSEMBLY

B

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE CANISTER ASSEMBLY
a.

Replace the canister assembly (See page Engine / Hybrid System>1GR-FE EMISSION CONTROL>CANISTER>REMOVAL).

NOTICE:

When replacing the canister, check the canister pump module interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose.


A225201E01
4.981,0.794 5.165,0.978 0.184,0.184 10 *1 6.616,2.015 6.800,2.198 0.184,0.184 10 *2 6.49,3.603 6.674,3.787 0.184,0.184 10 *3 6.902,2.443 7.086,2.626 0.184,0.184 10 *a 4.54,2.974 4.724,3.157 0.184,0.184 10 *a 2.482,3.205 2.647,3.370 0.165,0.165 10 *4 4.752,1.3 4.823,0.862 4.823,0.862 4.952,0.862 false 6.381,2.2 6.497,2.084 6.497,2.084 6.591,2.084 false 6.161,3.447 6.373,3.669 6.373,3.669 6.458,3.669 false 2.959,2.624 2.553,3.03 2.553,3.03 2.553,3.163 false 6.317,1.087 6.508,0.896 6.508,0.896 6.649,0.896 false 6.686,0.83 6.856,0.995 0.170,0.165 10 *5

Text in Illustration
*1 Fuel Tank Vent Hose *2 Vent Hose
*3 Air Inlet Port *4 Fuel Tank
*5 Canister Assembly - -
*a Inspection Area (check for disconnection and/or cracks) - -



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
HINT:

If the exhaust pipe has been removed, go to the next step before reinstalling it.



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
7.REPLACE ECM

NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Start the engine and warm it up.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTC: P0452 or P0453.


j.

Check the DTC judgment result.

HINT:

If the DTC judgment result is NORMAL, the repair has been successfully completed.




NEXT

COMPLETED