Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU.

The skid control ECU converts these wheel speed signals into a pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of this pulse signal.

A115899E11
0.43,1.047 1.579,1.425 1.149,0.378 10 from Wheel Speed Sensor 1.817,1.96 3.237,2.123 1.420,0.163 10 Skid Control ECU 3.722,1.96 5.142,2.123 1.420,0.163 10 Combination Meter 3.113,0.599 3.533,0.776 0.420,0.177 10 Pulse 5.039,0.599 5.441,0.776 0.402,0.177 10 Pulse 6.045,1.324 6.492,1.486 0.448,0.163 10 ECM

DTC No. DTC Detection Condition Trouble Area
P0500 While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the ECM (2 trip detection logic).
·

Open or short in speed signal circuit

·

Vehicle speed sensor

·

Combination meter assembly

·

ECM

·

Skid control ECU



MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when the indicated vehicle speed is higher than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite this condition being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM

A206532E05
6.279,0.612 6.528,0.768 0.248,0.156 10 5 V 5.52,0.886 5.847,1.046 0.327,0.161 10 SPD 5.275,0.939 5.482,1.100 0.207,0.161 10 18 6.036,1.845 6.326,1.997 0.290,0.151 10 F51 6.036,1.985 6.387,2.150 0.350,0.165 10 ECM 4.36,1.037 4.572,1.179 0.211,0.142 10 5B 3.464,1.037 3.675,1.179 0.211,0.142 10 5B 4.402,0.836 4.552,0.992 0.150,0.156 10 2 3.462,0.836 3.655,0.992 0.193,0.156 10 25 3.32,1.406 4.656,1.558 1.336,0.151 10 No. 5 Junction Block 2.595,0.951 2.798,1.107 0.203,0.156 10 28 2.33,0.949 2.555,1.104 0.225,0.156 10 +S 1.091,1.033 1.260,1.198 0.170,0.165 10 SI 0.839,1.039 1.042,1.194 0.202,0.156 10 29 1.235,1.841 1.530,2.006 0.295,0.165 10 F14 1.235,1.981 2.442,2.146 1.207,0.165 10 Combination Meter 0.105,2.691 1.544,2.860 1.438,0.170 10 from Skid Control ECU

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.


e.

Drive the vehicle.


f.

Read the value displayed on the intelligent tester.

OK:

Vehicle speeds displayed on intelligent tester and speedometer display are equal.




OK

NG

2.CHECK COMBINATION METER SYSTEM
2.CHECK COMBINATION METER SYSTEM
a.

Inspect the circuits that send vehicle speed signals to this system in the meter system (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit).


b.

During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.



NEXT

3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F14-28 (+S) - F51-18 (SPD) Always Below 1 Ω



d.

Reconnect the ECM connector.


e.

Reconnect the combination meter assembly connector.



OK

NG

4.CHECK HARNESS AND CONNECTOR (ECM - NO. 5 JUNCTION BLOCK)
4.CHECK HARNESS AND CONNECTOR (ECM - NO. 5 JUNCTION BLOCK)
a.

Disconnect the ECM connector.


b.

Disconnect the No. 5 junction block connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
5B-2 - F51-18 (SPD) Always Below 1 Ω



d.

Reconnect the ECM connector.


e.

Reconnect the No. 5 junction block connector.



OK

REPAIR OR REPLACE NO. 5 JUNCTION BLOCK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR