Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › 2009.08–2013.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If signals which indicate the brake pedal is being depressed and released are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal switch conditions are as shown in the table below.

Signal Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a), (b) and (c) are met for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) STP signal is OFF when the ST1- signal is OFF.
·

Short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

A227130E02
5.042,0.302 5.146,0.448 0.104,0.146 10 false 1 4.396,0.302 4.5,0.448 0.104,0.146 10 false 2 5.042,0.74 5.146,0.885 0.104,0.146 10 false 3 4.396,0.74 4.5,0.885 0.104,0.146 10 false 4 4.292,1.229 5.406,1.583 1.115,0.354 10 false Stop Light Switch Assembly 4.271,1.063 4.469,1.208 0.198,0.146 10 false A4 6.344,3.99 6.698,4.156 0.354,0.167 10 false ECM 6.083,0.385 6.406,0.563 0.323,0.177 10 false STP 6.083,0.823 6.438,1.01 0.354,0.188 10 false ST1- 5.781,0.208 5.979,0.354 0.198,0.146 10 false 18 5.833,0.656 5.948,0.802 0.115,0.146 10 false 8 5.729,0.438 6.01,0.604 0.281,0.167 10 false F50 5.729,0.875 6.01,1.042 0.281,0.167 10 false F51 3.5,0.583 3.917,0.76 0.417,0.177 10 false STOP 3.563,1.01 3.854,1.188 0.292,0.177 10 false IGN 2.083,1.385 2.323,1.552 0.24,0.167 10 false 1C 2.646,1.385 2.885,1.552 0.24,0.167 10 false 1C 2.083,2.76 2.323,2.927 0.24,0.167 10 false 1E 2.656,2.771 2.896,2.938 0.24,0.167 10 false 1C 0.563,1.406 0.844,1.573 0.281,0.167 10 false ALT 0.802,3.094 1.167,3.26 0.365,0.167 10 false P/I-B 0.885,3.51 1.115,3.688 0.229,0.177 10 false ST 1.698,1.792 1.958,1.958 0.26,0.167 10 false IG2 1.865,2.344 2.125,2.51 0.26,0.167 10 false IG2 2.094,3.469 2.354,3.635 0.26,0.167 10 false IG2 0.667,4.021 1.156,4.219 0.49,0.198 10 false Battery 3.125,2.135 4.573,2.333 1.448,0.198 10 false No. 1 Integration Relay 1.906,1.385 2.021,1.563 0.115,0.177 10 false 4 2.469,1.396 2.583,1.573 0.115,0.177 10 false 3 1.906,2.719 2.021,2.896 0.115,0.177 10 false 1 2.458,2.719 2.573,2.896 0.115,0.177 10 false 1 1.583,3.49 1.917,3.646 0.333,0.156 10 false AM2 1.396,3.229 1.51,3.396 0.115,0.167 10 false 7 2.396,3.229 2.51,3.396 0.115,0.167 10 false 6 1.49,3.823 1.792,3.99 0.302,0.167 10 false F15 1.49,3.958 2.417,4.125 0.927,0.167 10 false Ignition Switch

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the intelligent tester on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

5.

Check the STP signal when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed STP signal ON
Released STP signal OFF

PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
U180627E02
0.115,0.083 0.281,0.25 0.167,0.167 10 false *a 0.604,1.802 0.854,2.031 0.25,0.229 10 false A4

a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A4-2 - Body ground Always 11 to 14 V
A4-4 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


c.

Reconnect the stop light switch assembly connector.



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK ECM (STP AND ST1- VOLTAGE)
A388729E01
0.26,2.656 0.625,2.854 0.365,0.198 0.688,2.646 1.052,2.844 0.365,0.198 0.438,3.833 0.667,3.188 true 1.25,3.844 0.74,3.208 true 0.094,0.604 0.406,0.802 0.313,0.198 10 false *a 1.708,0.583 2.021,0.781 0.313,0.198 10 false *b 0.104,2.396 0.417,2.594 0.313,0.198 10 false *c 0.365,3.885 0.979,4.094 0.615,0.208 10 false 8 (ST1-) 0.323,2.677 0.635,2.875 0.313,0.198 10 false F51 0.75,2.667 1.063,2.865 0.313,0.198 10 false F50 1.167,3.896 1.781,4.104 0.615,0.208 10 false 18 (STP)

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
F51-8 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
F50-18 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V


Text in Illustration
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


d.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR