Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2102  Throttle Actuator Control Motor Circuit Low  P2103  Throttle Actuator Control Motor Circuit High  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.

The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body with motor assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.

DTC No. DTC Detection Condition Trouble Area
P2102 Conditions (a) and (b) are met for 2.0 seconds (1 trip detection logic):
(a) Throttle actuator duty ratio is 80% or more.
(b) Throttle actuator current is below 0.5 A.
·

Open in throttle actuator circuit

·

Throttle actuator

·

ECM


P2103 Either condition is met (1 trip detection logic):
·

There is a hybrid IC diagnosis signal failure.

·

There is a hybrid IC current limiter port failure.


·

Short in throttle actuator circuit

·

Throttle actuator

·

Throttle valve

·

Throttle body with motor assembly

·

ECM




MONITOR DESCRIPTION

The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, if it is stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and stores a DTC.

Example:

When the electrical current is less than 0.5 A and the throttle actuator duty ratio is 80% or more, the ECM interprets this as the current being outside the standard range, illuminates the MIL and stores DTC P2102.

If the malfunction is not repaired successfully, the DTC is stored when the engine is quickly revved to a high rpm several times after the engine is started and has idled for 5 seconds.

FAIL-SAFE

When either of these DTCs or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected and the ignition switch is turned off.

WIRING DIAGRAM

A227104E01
1.381,3.265 1.678,3.426 0.298,0.161 10 B13 1.388,3.426 3.610,3.619 2.222,0.193 10 Throttle Body with Motor Assembly 0.927,4.11 1.389,4.313 0.461,0.202 10 Battery 4.112,1.81 4.685,1.989 0.573,0.179 10 Shielded 2.89,1.132 3.296,1.315 0.406,0.183 10 ETCS 5.536,0.803 5.743,0.954 0.207,0.151 10 23 5.496,0.987 5.767,1.133 0.271,0.146 10 B38 5.812,0.897 6.153,1.062 0.341,0.165 10 +BM 5.537,1.96 5.784,2.097 0.247,0.137 10 20 5.5,2.154 5.785,2.347 0.286,0.193 10 B39 5.539,2.587 5.738,2.751 0.199,0.163 10 29 5.501,2.768 5.784,2.919 0.283,0.151 10 B38 2.767,2.061 3.000,2.217 0.232,0.156 10 M+ 2.781,2.677 2.985,2.824 0.204,0.147 10 M- 3.066,2.054 3.183,2.210 0.117,0.156 10 2 3.065,2.671 3.174,2.840 0.110,0.170 10 1 5.535,3.186 5.728,3.342 0.193,0.156 10 30 5.501,3.368 5.794,3.523 0.293,0.156 10 B38 5.532,3.775 5.725,3.945 0.193,0.170 10 10 5.501,3.955 5.795,4.101 0.294,0.146 10 B39 5.531,4.368 5.724,4.556 0.193,0.188 10 12 5.5,4.548 5.803,4.689 0.303,0.142 10 B38 5.816,2.056 6.046,2.235 0.230,0.179 10 M+ 5.812,2.672 6.005,2.819 0.193,0.147 10 M- 5.812,3.354 6.200,3.524 0.387,0.170 10 GE01 5.815,3.859 6.198,4.002 0.383,0.144 10 ME01 5.815,4.54 6.010,4.712 0.195,0.172 10 E1 6.13,5.11 6.480,5.275 0.350,0.165 10 ECM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


·

The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Duty (Open) / Throttle Motor Duty (Close)) can be read using the intelligent tester. However, the ECM shuts off the throttle actuator current when the ETCS malfunctions.



PROCEDURE

1.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.

Inspection the throttle body with motor assembly (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>THROTTLE BODY>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B13-2 (M+) - B39-20 (M+) Always Below 1 Ω
B13-1 (M-) - B38-29 (M-) Always Below 1 Ω
B13-2 (M+) or B39-20 (M+) - Body ground Always 10 kΩ or higher
B13-1 (M-) or B38-29 (M-) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle body with motor assembly connector.


e.

Reconnect the ECM connector.



OK

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Check for foreign objects between the throttle valve and housing.

OK:

No foreign objects between throttle valve and housing.




OK

4.INSPECT THROTTLE VALVE

NG

REMOVE FOREIGN OBJECT AND CLEAN THROTTLE BODY WITH MOTOR ASSEMBLY

4.INSPECT THROTTLE VALVE
a.

Check if the throttle valve opens and closes smoothly.

OK:

Throttle valve opens and closes smoothly.




OK

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY