Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2111  Throttle Actuator Control System - Stuck Open  P2112  Throttle Actuator Control System - Stuck Closed  


DESCRIPTION

The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body with motor assembly. The throttle position sensor provides feedback to the ECM so that the ECM can control the throttle actuator (throttle valve) appropriately in response to driver inputs.

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.

DTC No. DTC Detection Condition Trouble Area
P2111 Throttle actuator does not close when signaled by the ECM (1 trip detection logic).
·

Throttle actuator

·

Throttle body with motor assembly

·

Throttle valve


P2112 Throttle actuator does not open when signaled by the ECM (1 trip detection logic).
·

Throttle actuator

·

Throttle body with motor assembly

·

Throttle valve




MONITOR DESCRIPTION

The ECM determines that there is a malfunction in the ETCS when the throttle valve remains at a fixed angle despite a high drive current from the ECM. The ECM illuminates the MIL and stores a DTC.

If the malfunction is not repaired successfully, the DTC is stored when the accelerator pedal is fully depressed and released quickly (to fully open and close the throttle valve) after the engine is next started.

FAIL-SAFE

When either of these DTCs or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected and the ignition switch is turned off.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for contamination between the throttle valve and housing. If necessary, clean the throttle body with motor assembly and check that the throttle valve moves smoothly.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.




OK

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.



e.

Start the engine, and fully depress and release the accelerator pedal quickly (to fully open and close the throttle valve).


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
No DTC A
P2111 or P2112 B



A

B