Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  


DESCRIPTION

Refer to DTC P2120 (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P2120).

DTC No. DTC Detection Condition Trouble Area
P2121 Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

ECM



MONITOR DESCRIPTION

When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal sensor assembly is malfunctioning. The ECM turns on the MIL and stores the DTC.

FAIL-SAFE

The accelerator pedal sensor assembly has two (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the two sensor circuits and switches to limp mode. In limp mode, the functioning circuit is used to calculate the accelerator pedal position to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the accelerator pedal as being fully released. In this case, the throttle valve remains closed as if the engine is idling.

If a pass condition is detected and the ignition switch is turned off, the fail-safe operation stops and the system returns to normal.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

This DTC relates to the accelerator pedal sensor assembly.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


e.

Read DTCs.

Result
Display (DTC Output) Proceed to
P2121 A
P2121 and other DTCs B

HINT:

If any DTCs other than P2121 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (ACCEL SENSOR OUT NO.1 AND ACCEL SENSOR OUT NO.2)

B

2.READ VALUE USING INTELLIGENT TESTER (ACCEL SENSOR OUT NO.1 AND ACCEL SENSOR OUT NO.2)
A208621E02
0.67,1.751 0.875,1.925 0.205,0.174 10 *a 2.612,1.751 2.803,1.925 0.191,0.174 10 *b

a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.


d.

Read the values displayed on the intelligent tester.

Standard Voltage:
Accelerator Pedal Operations Accel Sensor Out No.1 Accel Sensor Out No.2
Released 0.5 to 1.1 V 1.2 to 2.0 V
Depressed 2.6 to 4.5 V 3.4 to 4.7 V


Text in Illustration
*a Depressed
*b Released



OK

NG

3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL).



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.



d.

Start the engine.


e.

Allow the engine to idle for 15 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
P2121 A
No output B



A

B

SYSTEM OK