Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM D

1GR-FE ENGINE CONTROL  SFI SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


When troubleshooting OBD II (On-Board Diagnostics) vehicles, the intelligent tester (complying with SAE J1987) must be connected to the DLC3 (Data Link Connector 3) of the vehicle. Various data in the vehicle's ECM (Engine Control Module) can then be read.


FI00534

OBD II regulations require that the vehicle's on-board computer illuminate the MIL (Malfunction Indicator Lamp) on the instrument panel when the computer detects a malfunction in:

1.

The emission control systems components.

2.

The powertrain control components which affect vehicle emissions.

3.

The computer itself.



In addition, the applicable DTCs prescribed by SAE J2012 are stored in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain stored in the ECM memory.


To check the DTCs, connect the intelligent tester to the DLC3. The intelligent tester displays DTCs, freeze frame data and a variety of the engine data. The DTCs and freeze frame data can be cleared with the intelligent tester. In order to enhance OBD function on vehicles and develop the Off-Board diagnosis system, Controller Area Network (CAN) communication is used in this system. CAN is a network which uses a pair of data transmission lines spanning multiple computers and sensors. It allows for high speed communications between the systems and simplification of the wire harness connections.



NORMAL MODE AND CHECK MODE


The diagnosis system operates in normal mode during normal vehicle use. In normal mode, 2 trip detection logic is used to ensure accurate detection of malfunctions. Check mode is also available as an option for technicians. In check mode, 1 trip detection logic is used to increase the system's ability to detect malfunctions, including intermittent problems, when simulating malfunction symptoms (intelligent tester only).


2 TRIP DETECTION LOGIC


When a malfunction is first detected, the DTC is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next subsequent drive cycle, the MIL is illuminated (2nd trip).



FREEZE FRAME DATA


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



DLC3 (Data Link Connector 3)


Check the DLC3 (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION).


BATTERY VOLTAGE


Standard voltage:

11 to 14 V


If voltage is below 11 V, replace or recharge the battery before proceeding.



MIL (Malfunction Indicator Lamp)


a.

The MIL is illuminated when the ignition switch is first turned ON (the engine is not running).


b.

The MIL should turn off when the engine is started. If the MIL remains illuminated, the diagnosis system has detected a malfunction or abnormality in the system.

HINT:

If the MIL is not illuminated when the ignition switch is first turned ON, check the MIL circuit (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>MIL Circuit).




ALL READINESS


HINT:
·

With All Readiness, you can check whether or not the DTC judgment has been completed by using the intelligent tester.

·

Check All Readiness after simulating malfunction symptoms or for validation after finishing repairs.



a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Clear the DTCs.


e.

Perform the DTC judgment driving pattern to run the DTC judgment.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


g.

Input the DTCs to be confirmed.


h.

Check the DTC judgment result.

Intelligent tester
Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

You should perform driving pattern after confirming DTC enabling conditions


UNKNOWN
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit