Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate the detection of vehicle malfunctions by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually; when the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A227133E01
1.062,1.093 1.348,1.249 0.286,0.156 10 F15 1.062,1.242 2.021,1.426 0.959,0.184 10 Ignition Switch 0.918,0.556 1.037,0.712 0.119,0.156 10 7 2.029,0.556 2.148,0.712 0.119,0.156 10 6 1.086,0.789 1.408,0.945 0.323,0.156 10 AM2 1.684,0.789 1.969,0.945 0.286,0.156 10 IG2 0.597,4.577 1.068,4.761 0.471,0.184 10 Battery 0.511,2.597 0.852,2.762 0.341,0.165 10 P/I-B 0.44,1.649 0.661,1.823 0.221,0.174 10 ST 1.088,2.418 1.300,2.583 0.211,0.165 10 1E 1.13,2.233 1.258,2.388 0.128,0.156 10 1 1.627,2.279 1.904,2.435 0.276,0.156 10 IG2 1.66,3.022 1.936,3.178 0.276,0.156 10 IG2 1.87,3.54 1.989,3.715 0.119,0.174 10 4 2.853,3.54 2.972,3.715 0.119,0.174 10 3 2.064,3.54 2.275,3.696 0.211,0.156 10 1C 2.559,3.54 2.770,3.696 0.211,0.156 10 1C 2.853,2.088 2.972,2.262 0.119,0.174 10 1 2.559,2.088 2.770,2.244 0.211,0.156 10 1C 2.914,4.007 3.459,4.163 0.545,0.156 10 GAUGE 3.811,3.755 4.022,3.920 0.211,0.165 10 17 4.072,4.016 4.339,4.182 0.267,0.165 10 IG+ 4.866,4.016 5.216,4.182 0.350,0.165 10 CHK 5.258,3.755 5.451,3.929 0.193,0.174 10 30 3.708,4.549 5.577,4.742 1.869,0.193 10 Combination Meter Assembly 3.708,4.409 3.993,4.583 0.286,0.174 10 F14 5.794,3.746 5.987,3.929 0.193,0.184 10 13 6.074,4.007 6.258,4.191 0.184,0.184 10 W 6.355,5.121 6.705,5.286 0.350,0.165 10 ECM 6.355,4.965 6.631,5.120 0.276,0.156 10 F51 3.18,2.681 4.660,2.865 1.480,0.184 10 No. 1 Integration Relay

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result
Condition Proceed to
MIL remains ON A
MIL does not illuminate B



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


d.

Check if any DTCs have been stored. Note down any DTCs.



f.

Check if the MIL goes off.

OK:

MIL goes off.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



d.

Reconnect the ECM connector.



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-13 (W) or F14-30 (CHK) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the combination meter assembly connector.



OK

REPAIR OR REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL is illuminated.




OK

SYSTEM OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Check that the engine starts.

Result
Result Proceed to
Engine starts A
Engine does not start* B

HINT:

*: The intelligent tester cannot communicate with the ECM.




A

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)

B

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)
a.

Refer to the combination meter troubleshooting procedure (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

NG

REPAIR OR REPLACE COMBINATION METER ASSEMBLY