Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2015.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM U

1GR-FE ENGINE CONTROL  SFI SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed Speed indicated on the speedometer.
Engine Speed Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
690 to 790 rpm: Idling -
Calculate Load Load calculated by ECM/
Min.: 0%, Max.: 100.0%
·

10 to 16.4%: Idling

·

10 to 18.9%: Driving without load (2500 rpm)


-
Vehicle Load Vehicle load/
Min.: 0%, Max.: 25700.0%
Actual vehicle load -
MAF Air flow rate from mass air flow meter/
Min.: 0 gm/sec., Max.: 655.35 gm/sec.
2.5 to 4.7 gm/sec.: Idling If the value is approximately 0.0 gm/sec.:
·

Mass air flow meter power source circuit is open or shorted.

·

VG circuit is open or shorted.


If the value is 160.0 gm/sec. or more:
·

E2G circuit is open.


Atmosphere Pressure Atmospheric pressure/
Min.: 0 kPa, Max.: 255 kPa
Equivalent to atmospheric pressure (absolute pressure) -
Coolant Temp Engine coolant temperature:
Min.: -40°C, Max.: 215°C
80 to 100°C (176 to 212°F): After warming up If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F), the sensor circuit is shorted.
Intake Air Intake air temperature/
Min.: -40°C, Max.: 140°C
Equivalent to ambient air temperature If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F), the sensor circuit is shorted.
Engine Run Time Engine run time/
Min.: 0 seconds, Max.: 65535 seconds
Time after engine start Service data.
Initial Engine Coolant Temp Initial engine coolant temperature/
Min.: -40°C, Max.: 119.3°C
Close to ambient air temperature Service data.
Initial Intake Air Temp Initial intake air temperature/
Min.: -40°C, Max.: 119.3°C
Close to ambient air temperature Service data.
Battery Voltage Battery voltage/
Min.: 0 V, Max.: 65.535 V
11 to 14 V: Idling -
Glow Indicator Supported Status of glow indicator supported/
Unsupp or Supp
Unsupp -
Glow Indicator Glow indicator/
ON or OFF
OFF -
Accelerator Position Accelerator pedal position/
Min.: 0%, Max.: 399.9%
Actual accelerator pedal position -
Accel Sens. No.1 Volt % Absolute Accelerator Pedal Position (APP) No. 1/
Min.: 0%, Max.: 100.0%
·

10 to 22%: Accelerator pedal released

·

54 to 86%: Accelerator pedal fully depressed


-
Accel Sens. No.2 Volt % Absolute APP No. 2/
Min.: 0%, Max.: 100.0%
·

12 to 42%: Accelerator pedal released

·

66 to 98%: Accelerator pedal fully depressed


-
Accel Sensor Out No.1 APP sensor No. 1 voltage/
Min.: 0 V, Max.: 4.980 V
·

0.5 to 1.1 V: Accelerator pedal released

·

2.6 to 4.5 V: Accelerator pedal fully depressed


-
Accel Sensor Out No.2 APP sensor No. 2 voltage/
Min.: 0 V, Max.: 4.980 V
·

1.2 to 2.0 V: Accelerator pedal released

·

3.4 to 4.75 V: Accelerator pedal fully depressed


-
Accelerator Idle Position Whether or not accelerator pedal position sensor detecting idle/
ON or OFF
ON: Idling -
Accel Fully Close Learn #1 Accelerator fully closed learned value No. 1/
Min.: 0 deg, Max.: 124.5 deg
- ETCS service data.
Accel Fully Close Learn #2 Accelerator fully closed learned value No. 2/
Min.: 0 deg, Max.: 124.5 deg
- ETCS service data.
Throttle Sensor Volt % Absolute throttle position sensor/
Min.: 0%, Max.: 100.0%
·

10 to 22%: Throttle fully closed

·

64 to 96%: Throttle fully open


The calculated value based on VTA1.
Throttl Sensor #2 Volt % Throttle position sensor #2/
Min.: 0%, Max.: 100.0%
·

42 to 62%: Throttle fully closed

·

92 to 100%: Throttle fully open


The calculated value based on VTA2.
ST1 Brake pedal signal/
ON or OFF
ON: Brake pedal depressed -
System Guard System guard/
ON or OFF
- ETCS service data.
Open Side Malfunction Open side malfunction/
ON or OFF
- ETCS service data.
Throttle Idle Position Whether or not throttle position sensor detecting idle/
ON or OFF
·

ON: Accelerator pedal released

·

OFF: Accelerator pedal depressed


-
Throttle Require Position Required throttle position/
Min.: 0 V, Max.: 4.980 V
0.5 to 1.1 V: Idling -
Throttle Sensor Position* Throttle sensor position/
Min.: 0%, Max.: 100.0%
·

0%: Throttle fully closed

·

50 to 80%: Throttle fully open


Recognition value of the throttle opening angle in the ECM.
Throttle Position No. 1 Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.980 V
·

0.5 to 1.1 V: Accelerator pedal released

·

3.2 to 4.8 V: Accelerator pedal fully depressed

·

0.6 to 1.4 V: Fail-safe operating


-
Throttle Position No. 2 Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.980 V
·

2.1 to 3.1 V: Accelerator pedal released

·

4.6 to 5.0 V: Accelerator pedal fully depressed

·

2.1 to 3.1 V: Fail-safe operating


-
Throttle Position Command Throttle position command value/
Min.: 0 V, Max.: 4.980 V
0.5 to 4.8 V -
Throttle Sens Open Pos #1 Throttle position sensor No. 1/
Min.: 0 V, Max.: 4.980 V
0.6 to 1.4 V ETCS service data.
Throttle Sens Open Pos #2 Throttle position sensor No. 2/
Min.: 0 V, Max.: 4.980 V
1.7 to 2.5 V ETCS service data.
Throttle Motor Current Throttle actuator current/
Min.: 0 A, Max.: 19.9 A
0 to 3.0 A: Idling ETCS service data.
Throttle Motor DUTY Throttle actuator/
Min.: 0%, Max.: 100.0%
0.5 to 40%: Idling ETCS service data.
Throttle Motor Duty (Open) Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 255%
0 to 40%: Idling ETCS service data.
Throttle Motor Duty (Close) Throttle actuator duty ratio (close)/
Min.: 0%, Max.: 255%
0 to 40%: Idling ETCS service data.
Throttle Fully Close Learn Throttle valve fully closed (learned value)/
Min.: 0 V, Max.: 4.980 V
0.4 to 1.0 V: Accelerator pedal released -
+BM Voltage +BM voltage/
Min.: 0 V, Max.: 79.998 V
11 to 14 V: Ignition switch ON and system normal ETCS service data.
Actuator Power Supply Actuator power supply/
ON or OFF
ON: Idling ETCS service data.
Throttle Position Throttle valve opening angle/
Min.: 0 deg, Max.: 499.99 deg
- For use when engine stall, starting problems or rough idle is present.
ISC Flow Flow rate calculated using information from each sensor/
Min.: 0 L/s, Max.: 79.99 L/s
- For use when engine stall, starting problems or rough idle is present.
ISC Position Requested opening amount calculated using ISC control/
Min.: 0 deg, Max.: 499.99 deg
- This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow).
ISC Feedback Value ISC feedback compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
ISC Learning Value ISC learned compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
Electric Load Feedback Val Compensation flow rate according to electrical load/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
Air Conditioner FB Val Compensation flow rate according to air conditioner load/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
PS Feedback Val Compensation flow rate according to power steering load/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
Low Revolution Control Low engine speed control operation state/
ON or OFF
- For use when engine stall, starting problems or rough idle is present.
N Range Status Shift lever N status/
ON or OFF
- For use when engine stall, starting problems or rough idle is present.
Eng Stall Control FB Flow Intake air compensation flow rate/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
Deposit Loss Flow Flow loss due to deposits/
Min.: -40 L/s, Max.: 39.99 L/s
-
·

This value indicates the amount of compensation for a decrease in flow passage area due to the buildup of deposits on the throttle valve.

·

Check this value for reference when the engine stalls, is difficult to start, or idles roughly.

·

When the ISC learned value is initialized by disconnecting the battery negative terminal or removing the fuses (EFI NO. 1 and ETCS fuses), performing the following procedures in order to quickly relearn the Deposit Loss Flow value. After the Deposit Loss Flow has been relearned, gradual fine adjustments will continue automatically.

·

Start the engine cold and allow the engine to idle.

·

After the engine is warmed up (engine coolant temperature is above 80°C [176°F]), allow the engine to idle for an additional 5 minutes.

·

Turn the ignition switch off and wait for 30 seconds.

·

Start the engine again, and allow the engine to idle for 5 minutes.



Fuel Pump Duty Fuel pump duty/
Min.: 0%, Max.: 399.9%
- -
Injector (Port) Injection period of the No. 1 cylinder/
Min.: 0 μs, Max.: 65535 μs
1600 to 2400 μs: Idling -
Injection Volum (Cylinder 1) Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
0 to 0.5 ml Fuel injection volume of 10 injections.
Vacuum Pump Key-off EVAP system pump status/
ON or OFF
- Active Test support data.
Current Fuel Type Status of the current fuel type Gasoline/petrol -
EVAP (Purge) VSV Purge VSV control duty/
Min.: 0%, Max.: 100.0%
0 to 100%: During idling Command signal from the ECM.
Evap Purge Flow Purge flow/
Min.: 0%, Max.: 399.9%
0 to 100%: Idling -
Purge Density Learn Value Purge density learned value/
Min.: -200, Max.: 199.993
Idling: -40 to 0 Service data.
Vapor Pressure Pump Vapor pressure/
Min.: 0 kPa (0 mmHg), Max.: 1441.770 kPa (10815.979 mmHg)
Approximately 100 kPa (750 mmHg): Ignition switch ON EVAP system pressure is monitored by the canister pressure sensor.
Vapor Pressure (Calculated) Calculated EVAP system pressure/
Min.: -720.896 kPa (-5408.072 mmHg), Max.: 720.874 kPa (5407.907 mmHg)
Approximately 100 kPa (750 mmHg): Ignition switch ON -
EVAP System Vent Valve Key-off EVAP system vent valve status/
ON or OFF
- Active Test support data.
EVAP Purge VSV VSV status for EVAP control/
ON or OFF
- Active Test support data.
Purge Cut VSV Duty Purge cut VSV duty/
Min.: 0%, Max.: 399.9%
- -
Target Air-Fuel Ratio Target air fuel ratio/
Min.: 0, Max.: 1.990
0.8 to 1.2: During idling -
AF Lambda B1S1 Short-term fuel trim associated with the Bank 1 Sensor 1/
Min.: 0, Max.: 1.990
·

Value less than 1 (0.000 to 0.999) = Rich

·

1 = Stoichiometric air fuel ratio

·

Value more than 1 (1.001 to 1.990) = Lean


-
AF Lambda B2S1 Short-term fuel trim associated with the Bank 2 Sensor 1/
Min.: 0, Max.: 1.990
·

Value less than 1 (0.000 to 0.999) = Rich

·

1 = Stoichiometric air fuel ratio

·

Value more than 1 (1.001 to 1.990) = Lean


-
AFS Voltage B1S1 Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/
Min.: 0 V, Max.: 7.990 V
2.8 to 3.8 V: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Voltage B2S1 Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/
Min.: 0 V, Max.: 7.990 V
2.8 to 3.8 V: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Current B1S1 Air fuel ratio sensor current (for Bank 1 Sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
AFS Current B2S1 Air fuel ratio sensor current (for Bank 2 Sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
A/F Heater Duty #1 Air fuel ratio sensor heater duty ratio (for Bank 1)/
Min.: 0%, Max.: 399.9%
0 to 100% -
A/F Heater Duty #2 Air fuel ratio sensor heater duty ratio (for Bank 2)/
Min.: 0%, Max.: 399.9%
0 to 100% -
O2S B1S2 Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
O2S B2S2 Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
O2S Impedance B1S2 Sub heated oxygen sensor impedance (Bank 1 Sensor 2)/
Min.: 0 ohm, Max.: 21247.67 ohm
5 to 15000 ohm After driving approx. 10 min. in an urban area.
O2S Impedance B2S2 Sub heated oxygen sensor impedance (Bank 2 Sensor 2)/
Min.: 0 ohm, Max.: 21247.67 ohm
5 to 15000 ohm After driving approx. 10 min. in an urban area.
O2 Heater B1S2 Heated oxygen sensor heater (for Bank 1 Sensor 2)/
Active or Not Act
- -
O2 Heater B2S2 Heated oxygen sensor heater (for Bank 2 Sensor 2)/
Active or Not Act
- -
O2 Heater Curr Val B1S2 Heated oxygen sensor current (for Bank 1 Sensor 2)/
Min.: 0 A, Max.: 4.999 A
- -
O2 Heater Curr Val B2S2 Heated oxygen sensor current (for Bank 2 Sensor 2)/
Min.: 0 A, Max.: 4.999 A
- -
Short FT #1 Short-term fuel trim of bank 1/
Min.: -100%, Max.: 99.200%
-20 to +20% This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
Long FT #1 Long-term fuel trim of bank 1/
Min.: -100%, Max.: 99.200%
-20 to +20%
·

This item refers to the overall fuel compensation carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.

·

Air fuel ratio feedback leaning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range. [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.


Total FT #1 Total fuel trim of bank 1/
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling -
Short FT #2 Short-term fuel trim of bank 2/
Min.: -100%, Max.: 99.200%
-20 to +20% This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
Long FT #2 Long-term fuel trim of bank 2/
Min.: -100%, Max.: 99.200%
-20 to +20%
·

This item refers to the overall fuel compensation carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.

·

Air fuel ratio feedback leaning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #2" indicates the learned value for the current operating range. [A/F Learn Value Idle #2], [A/F Learn Value Low #2], [A/F Learn Value Mid1 #2], [A/F Learn Value Mid2 #2] and [A/F Learn Value High #2] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #2" indicates the current engine operating range.


Total FT #2 Total fuel trim of bank 2/
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling -
Fuel System Status #1 Fuel system status (Bank 1)/
Unused, OL, CL, OLDrive, OLFault or CLFault
CL: Idling after warming up
·

OL (Open Loop): Has not yet satisfied conditions to go to closed loop.

·

CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.

·

OL Drive: Open loop due to driving conditions (fuel enrichment).

·

OL Fault: Open loop due to a detected system fault.

·

CL Fault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.


Fuel System Status #2 Fuel system status (Bank 2)/
Unused, OL, CL, OLDrive, OLFault or CLFault
CL: Idling after warming up
·

OL (Open Loop): Has not yet satisfied conditions to go to closed loop.

·

CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.

·

OL Drive: Open loop due to driving conditions (fuel enrichment).

·

OL Fault: Open loop due to a detected system fault.

·

CL Fault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.


Air Pump Pressure (Absolute) Air pump pressure (absolute) (for Bank 1)/
Min.: 0 kPa, Max.: 65535 kPa
Atmospheric pressure +1 kPa or more: Air pump on, emission control valve open
Close to atmospheric pressure: Air pump off, emission control closed
Refer to DTC P2431 (See page (Click here)).
Air Pump2 Pressure (Absolute) Air pump pressure (absolute) (for Bank 2)/
Min.: 0 kPa, Max.: 65535 kPa
Atmospheric pressure +1 kPa or more: Air pump on, emission control valve open
Close to atmospheric pressure: Air pump off, emission control valve closed
Refer to DTC P2431 (See page (Click here)).
Air Pump Pulsation Pressure Air pump pulsation pressure/
Min.: 0 kPa, Max.: 655.35 kPa
- Cumulative pulsation pressure calculated by ECM (See page (Click here)).
Secondary Air Control VSV Secondary air control VSV status/
ON or OFF
ON: Secondary air control VSV operating -
2nd Air System Status Secondary air system status/
ON or OFF
ON: Secondary air injection system operating -
AI Test AI operation prohibition/
READY or NOT RDY
READY -
Subfreezing Conditions Subfreezing conditions status/
ON or OFF
- -
Air Pump Heater Air pump heater status/
ON or OFF
- Active Test support data
IGN Advance Ignition timing advance for No. 1 cylinder/
Min.: -64 deg., Max.: 63.5 deg.
BTDC 7 to 24 deg: Idling -
Knock Feedback Value Knocking feedback value/
Min.: -1024 deg(CA), Max.: 1023.9 deg(CA)
-3 deg(CA):
Driving at 70 km/h (44 mph)
Service data.
Knock Correct Learn Value Knocking correction learned value/
Min.: -1024 deg(CA), Max.: 1023.9 deg(CA)
5 to 28 deg(CA):
Driving at 70 km/h (44 mph)
Service data.
Idle Spark Advn Ctrl #1 Individual cylinder timing advance compensation amount (No. 1)/
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
- For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #2 Individual cylinder timing advance compensation amount (No. 2)/
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
- For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #3 Individual cylinder timing advance compensation amount (No. 3)/
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
- For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #4 Individual cylinder timing advance compensation amount (No. 4)/
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
- For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #5 Individual cylinder timing advance compensation amount (No. 5)/
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
- For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #6 Individual cylinder timing advance compensation amount (No. 6)/
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
- For use when engine stall, starting problems or rough idle is present.
VVT Control Status #1 Variable valve timing (VVT) control status (Bank 1)/
ON or OFF
- Active Test support data.
VVT Control Status #2 VVT control status (Bank 2)/
ON or OFF
- Active Test support data.
VVT Advance Fail VVT control failure status/
ON or OFF
ON: VVT control failure -
VVT Aim Angle #1 VVT target duty (Bank 1)/
Min.: 0%, Max.: 399.9%
0%: Idling VVT duty signal value during forced operation.
VVT Change Angle #1 VVT displacement angle (Bank 1)/
Min.: 0 DegFR, Max.: 639.9 DegFR
0 to 5 DegFR: Idling Displacement angle during forced operation.
VVT OCV Duty #1 Camshaft timing oil control valve operation duty (for Intake Side of Bank 1)/
Min.: 0%, Max.: 399.9%
0%: Idling Requested duty value for forced operation.
VVT Aim Angle #2 VVT target duty (Bank 2)/
Min.: 0%, Max.: 399.9%
0%: Idling VVT duty signal value during forced operation.
VVT Change Angle #2 VVT displacement angle (for Intake Side of Bank 2)/
Min.: 0 DegFR, Max.: 639.9 DegFR
0 to 5 DegFR: Idling Displacement angle during forced operation.
VVT OCV Duty #2 Camshaft timing oil control valve operation duty (Bank 2)/
Min.: 0%, Max.: 399.9%
0%: Idling Requested duty value for forced operation.
VVT Ex Hold Lrn Val #1 VVT exhaust hold duty ratio learned value (Bank 1)/
Min.: 0%, Max.: 399.9%
0 to 80%: Idling -
VVT Ex Chg Angle #1 VVT exhaust displacement angle (Bank 1)/
Min.: 0 DegFR, Max.: 639.9 DegFR
0 to 40 DegFR: Idling Displacement angle during forced operation.
VVT Ex OCV Duty #1 Camshaft timing oil control valve duty (for Exhaust Side of Bank 1)/
Min.: 0%, Max.: 399.9%
0 to 100%: Idling Requested duty value for forced operation.
VVT Ex Hold Lrn Val #2 VVT exhaust hold duty ratio learned value (Bank 2)/
Min.: 0%, Max.: 399.9%
0 to 80%: Idling -
VVT Ex Chg Angle #2 VVT exhaust displacement angle (Bank 2)/
Min.: 0 DegFR, Max.: 639.9 DegFR
0 to 40 DegFR: Idling Displacement angle during forced operation.
VVT Ex OCV Duty #2 Camshaft timing oil control valve duty (for Exhaust Side of Bank 2)/
Min.: 0%, Max.: 399.9%
0 to 100%: Idling Requested duty value for forced operation.
VVT Target Angle #1 VVT intake target angle (Bank 1)/
Min.: 0 DegFR, Max.: 639.9 DegFR
- -
VVT Target Angle #2 VVT intake target angle (Bank 2)/
Min.: 0 DegFR, Max.: 639.9 DegFR
- -
VVT Ex Target Angle #1 VVT exhaust target angle (Bank 1)/
Min.: 0 DegFR, Max.: 639.9 DegFR
- -
VVT Ex Target Angle #2 VVT exhaust target angle (Bank 2)/
Min.: 0 DegFR, Max.: 639.9 DegFR
- -
VN Turbo Type VN turbo type/
Not Avl, Commo, Vacuum, CAN Com or DC
Not Avl -
Catalyst Temp B1S1 Catalyst temperature (Bank 1, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
- -
Catalyst Temp B2S1 Catalyst temperature (Bank 2, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
- -
Catalyst Temp B1S2 Catalyst temperature (Bank 1, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
- -
Catalyst Temp B2S2 Catalyst temperature (Bank 2, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
- -
Starter Signal Starter signal/
ON or OFF
Open: Cranking -
Power Steering Signal Power steering oil pressure switch signal/ ON or OFF ON: Power steering operating -
Neutral Position SW Signal PNP switch status/
ON or OFF
ON: P or N position -
Transfer Neutral Neutral status of the transfer/
ON or OFF
ON: 4WD control switch in 2WD position -
4WD SW 4WD switch status/
ON or OFF
ON: Vehicle in 4WD (part-time 4WD vehicle) -
Transfer L4 L4 status of the transfer/
ON or OFF
ON: 4WD control switch in 4L position -
Stop Light Switch Stop light switch/
ON or OFF
ON: Brake pedal depressed -
A/C Signal A/C switch status/
ON or OFF
ON: A/C on -
Closed Throttle Position SW Closed throttle position switch/
ON or OFF
·

ON: Throttle fully closed

·

OFF: Throttle open


-
Fuel Cut Condition Fuel cut condition/
ON or OFF
ON: Fuel cut operating -
Immobiliser Communication Immobiliser communication/
ON or OFF
ON: Normal -
Check Mode Check mode/
ON or OFF
ON: Check mode on Refer to Check Mode Procedure (See page (Click here)).
SPD Test Result Check mode result for vehicle speed sensor/
Compl or Incmpl
- -
AS Test Result Check mode result for secondary air injection system/
Compl or Incmpl
- -
Misfire Test Result Check mode result for misfire monitor/
Compl or Incmpl
- -
OXS1 Test Result Check mode result for heated oxygen sensor (Bank 1)/
Compl or Incmpl
- -
OXS2 Test Result Check mode result for heated oxygen sensor (Bank 2)/
Compl or Incmpl
- -
A/F Test Results #2 Check mode result for air fuel ratio sensor (Bank 2)/
Compl or Incmpl
- -
A/F Test Results #1 Check mode result for air fuel ratio sensor (Bank 1)/
Compl or Incmpl
- -
Complete Parts Monitor Comprehensive component monitor/
Not Avl or Avail
- -
Fuel System Monitor Fuel system monitor/
Not Avl or Avail
- -
Misfire Monitor Misfire monitor/
Not Avl or Avail
- -
EGR/VVT Monitor EGR/VVT monitor/
Not Avl or Avail
- -
EGR/VVT Monitor EGR/VVT monitor/
Compl or Incmpl
- -
O2S(A/FS) Heater Monitor O2S (A/FS) heater monitor/
Not Avl or Avail
- -
O2S(A/FS) Heater Monitor O2S (A/FS) heater monitor/
Compl or Incmpl
- -
O2S(A/FS) Monitor O2S (A/FS) monitor/
Not Avl or Avail
- -
O2S(A/FS) Monitor O2S (A/FS) monitor/
Compl or Incmpl
- -
A/C Monitor A/C monitor/
Not Avl or Avail
- -
A/C Monitor A/C monitor/
Compl or Incmpl
- -
2nd Air Monitor 2nd air monitor/
Not Avl or Avail
- -
2nd Air Monitor 2nd air monitor/
Compl or Incmpl
- -
EVAP Monitor EVAP monitor/
Not Avl or Avail
- -
EVAP Monitor EVAP monitor/
Compl or Incmpl
- -
Heated Catalyst Monitor Heated catalyst monitor/
Not Avl or Avail
- -
Heated Catalyst Monitor Heated catalyst monitor/
Compl or Incmpl
- -
Catalyst Monitor Catalyst monitor/
Not Avl or Avail
- -
Catalyst Monitor Catalyst monitor/
Compl or Incmpl
- -
Component Monitor ENA Comprehensive component monitor/
Unable or Enable
- -
Component Monitor CMPL Comprehensive component monitor/
Compl or Incmpl
- -
Fuel System Monitor ENA Fuel system monitor/
Unable or Enable
- -
Fuel System Monitor CMPL Fuel system monitor/
Compl or Incmpl
- -
Misfire Monitor ENA Misfire monitor/
Unable or Enable
- -
Misfire Monitor CMPL Misfire monitor/
Compl or Incmpl
- -
EGR/VVT Monitor ENA EGR monitor/
Unable or Enable
- -
EGR/VVT Monitor CMPL EGR monitor/
Compl or Incmpl
- -
Heater Monitor ENA O2S (A/FS) heater monitor/
Unable or Enable
- -
Heater Monitor CMPL O2S (A/FS) heater monitor/
Compl or Incmpl
- -
O2S(A/FS) Monitor ENA O2S (A/FS) monitor/
Unable or Enable
- -
O2S(A/FS) Monitor CMPL O2S (A/FS) monitor/
Compl or Incmpl
- -
A/C Monitor ENA A/C monitor/
Unable or Enable
- -
A/C Monitor CMPL A/C monitor/
Compl or Incmpl
- -
2nd Air Monitor ENA 2nd air monitor/
Unable or Enable
- -
2nd Air Monitor CMPL 2nd air monitor/
Compl or Incmpl
- -
EVAP Monitor ENA EVAP monitor/
Unable or Enable
- -
EVAP Monitor CMPL EVAP monitor/
Compl or Incmpl
- -
Heated Cat Monitor ENA Heated catalyst monitor/
Unable or Enable
- -
Heated Cat Monitor CMPL Heated catalyst monitor/
Compl or Incmpl
- -
Catalyst Monitor ENA Catalyst monitor/
Unable or Enable
- -
Catalyst Monitor CMPL Catalyst monitor/
Compl or Incmpl
- -
TC Terminal TC terminal status/
ON or OFF
- -
# Codes (Include History) Number of codes/
Min.: 0, Max.: 255
- Number of DTCs stored.
MIL MIL status/
ON or OFF
ON: MIL on -
MIL ON Run Distance Distance driven with MIL on/
Min.: 0 km, Max.: 65535 km
Distance driven after DTC stored -
Running Time from MIL ON Running time from MIL ON/
Min.: 0 min, Max.: 65535 min
Running time after MIL turned on -
Time after DTC Cleared Time after DTCs cleared/
Min.: 0 min, Max.: 65535 min
Time after DTCs cleared -
Distance from DTC Cleared Distance after DTCs cleared/
Min.: 0 km, Max.: 65535 km
Driving distance after DTCs cleared -
Warmup Cycle Cleared DTC Warmup cycles after DTCs cleared/
Min.: 0, Max.: 255
- Number of warmup cycles after the DTCs are cleared.
Dist Batt Cable Disconnect Distance driven after battery cable disconnected/
Min.: 0 km, Max.: 65535 km
Total distance vehicle driven after battery cable disconnected -
IG OFF Elapsed Time Time after ignition switch off/
Min.: 0 min, Max.: 655350 min
Cumulative time after ignition switch off -
OBD Requirements OBD requirement OBD2 -
Number of Emission DTC Emissions-related DTCs - Number of emissions-related DTCs.
TC and TE1 TC and CG (TE1) terminals of DLC3/
ON or OFF
- -
Ignition Trig. Count Ignition counter/
Min.: 0, Max.: 65535
0 to 800 -
Cylinder #1 Misfire Count
to
Cylinder #6 Misfire Count
Misfire ratio of cylinder 1 to 6/
Min.: 0, Max.: 255
0 -
All Cylinders Misfire Count Misfire count of all cylinders/
Min.: 0, Max.: 255
0 to 35 -
Misfire RPM Engine speed for first misfire range/
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Misfire 0 -
Misfire Load Engine load for first misfire range/
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: Misfire 0 -
Misfire Margin Misfire monitoring/
Min.: -128%, Max.: 127.00%
-100 to 99.2% Misfire detection margin.
Catalyst OT MF F/C Fuel cut to prevent misfire causing catalyst overheating/
Not Avl or Avail
·

Avail: Fuel cut to prevent misfire causing catalyst overheating available

·

Not Avl: Fuel cut to prevent misfire causing catalyst overheating not available


-
Cat OT MF F/C History History of fuel cut to prevent misfire causing catalyst overheating/
ON or OFF
ON: Fuel cut operation history exists -
Cat OT MF F/C Cylinder #1 Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating -
Cat OT MF F/C Cylinder #2 Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating -
Cat OT MF F/C Cylinder #3 Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating -
Cat OT MF F/C Cylinder #4 Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating -
Cat OT MF F/C Cylinder #5 Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating -
Cat OT MF F/C Cylinder #6 Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating -
Engine Speed (Starter Off) Engine speed when starter off/
Min.: 0 rpm, Max.: 51199 rpm
- For use when engine stall, starting problems or rough idle is present.
Starter Count Number of times starter turned on after ignition switch turned to ON/
Min.: 0, Max.: 255
- For use when engine stall, starting problems or rough idle is present.
Run Dist of Previous Trip Distance driven during previous trip/
Min.: 0 km, Max.: 655.35 km
- Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
HINT:

Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.


Compression Leakage Count Compression leakage count/
Min.: 0, Max.: 255
0 When the counter displays 1 or higher during an engine stall, startability malfunction or rough idle, it may be the result of pressure loss caused by deposits jamming the valve, etc.
Rough Idle Status Status of the rough idle status/
Normal, Misfire, Continuous poor combustion, Intermittent poor combustion, Low frequency poor combustion
Normal The following list of statuses indicates the degree and frequency of rough idling from highest to lowest. Use this as a reference when trying to reproduce the rough idling.
1.

Misfire

2.

Continuous poor combustion

3.

Intermittent poor combustion

4.

Low frequency poor combustion


Plural Cylinders Rough Idle Status of the plural cylinders rough idle/
ON or OFF
OFF Indicates multiple cylinders are the cause of rough idling when ON.
Rough Idle #1 Status of the rough idle #1/
ON or OFF
OFF
·

Indicates speed has dropped compared to other cylinders and idling is rough for the indicated cylinder when ON.

·

This item indicates cylinders which are likely to be the cause of rough idle.


Rough Idle #2 Status of the rough idle #2/
ON or OFF
OFF Same as Rough Idle #1
Rough Idle #3 Status of the rough idle #3/
ON or OFF
OFF Same as Rough Idle #1
Rough Idle #4 Status of the rough idle #4/
ON or OFF
OFF Same as Rough Idle #1
Rough Idle #5 Status of the rough idle #5/
ON or OFF
OFF Same as Rough Idle #1
Rough Idle #6 Status of the rough idle #6/
ON or OFF
OFF Same as Rough Idle #1
Engine Starting Time Time elapsed after engine started (interval between ignition switch ON and off)/
Min.: 0 ms, Max.: 655350 ms
- For use when engine stall, starting problems or rough idle is present.
Previous Trip Coolant Temp Engine coolant temperature during previous trip/
Min.: -40°C, Max.: 215°C
- For use when engine stall, starting problems or rough idle is present.
Previous Trip Intake Temp Intake air temperature during previous trip/
Min.: -40°C, Max.: 215°C
- For use when engine stall, starting problems or rough idle is present.
Engine Oil Temperature Engine oil temperature (estimated temperature)/
Min.: -40°C, Max.: 215°C
- For use when engine stall, starting problems or rough idle is present.
Previous Trip Eng Oil Temp Engine oil temperature during previous trip/
Min.: -40°C, Max.: 215°C
- For use when engine stall, starting problems or rough idle is present.
Ambient Temp for A/C Ambient temperature for A/C/
Min.: -40°C, Max.: 215°C
- For use when engine stall, starting problems or rough idle is present.
Previous Trip Ambient Temp Ambient temperature during previous trip/
Min.: -40°C, Max.: 215°C
- For use when engine stall, starting problems or rough idle is present.
Engine Start Hesitation History of hesitation during engine start/
ON or OFF
- -
Low Rev for Eng Start History of low engine speed after engine start/
ON or OFF
- -
A/F Learn Value Idle #1 Air-fuel ratio learned value for idling (bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
A/F Learn Value Low #1 Air-fuel ratio learned value for low engine loads (bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid1 #1 Air-fuel ratio learned value for midsized engine loads 1 (bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid2 #1 Air-fuel ratio learned value for midsized engine loads 2 (bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the high load range (when the range of engine loads is divided into four parts).
A/F Learn Value High #1 Air-fuel ratio learned value for high engine loads (bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
A/F Learn Value Idle #2 Air-fuel ratio learned value for idling (bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
A/F Learn Value Low #2 Air-fuel ratio learned value for low engine loads (bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid1 #2 Air-fuel ratio learned value for midsized engine loads 1 (bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid2 #2 Air-fuel ratio learned value for midsized engine loads 2 (bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the high load range (when the range of engine loads is divided into four parts).
A/F Learn Value High #2 Air-fuel ratio learned value for high engine loads (bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
Power Steering Pressure Power steering oil pressure/
Min.: 0 MPa, Max.: 25.599 MPa
- -
ACT VSV A/C cut status for Active Test/
ON or OFF
- Active Test support data.
Brake Override system Status of the brake override system/
ON or OFF
- -
Idle Fuel Cut Fuel cut at idle/
ON or OFF
ON: Fuel cut operating Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
FC TAU Fuel cut TAU (fuel cut during very light load)/
ON or OFF
ON: Fuel cut operating The fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete.
Immobiliser Fuel Cut Status of the immobiliser fuel cut/
ON or OFF
- -
Immobiliser Fuel Cut History Status of the immobiliser fuel cut history/
ON or OFF
- -
Comm with Power Manage Status of the communication with power management control ECU/
Comm or No Comm
- -
Comm with Air Conditioner Status of the communication with air conditioning amplifier/
Comm or No Comm
- -
Electrical Load Signal 1 Electrical load signal/
ON or OFF
- -
Electrical Load Signal 2 Electrical load signal/
ON or OFF
- -
Model Code Model code - Used for identifying the model code:
GRN28#
Engine Type Engine type - Used for identifying the engine type:
1GRFE
Cylinder Number Number of cylinders/
Min.: 0, Max.: 255
- Used for identifying the number of cylinders:
6
Destination Destination - Used for identifying the destination:
A
Model Year Model year/
Min.: 1900, Max.: 2155
- Used for identifying the model year:
20##
Engine Speed of Cyl #1 Engine speed for cylinder 1/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #2 Engine speed for cylinder 2/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #3 Engine speed for cylinder 3/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #4 Engine speed for cylinder 4/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #5 Engine speed for cylinder 5/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #6 Engine speed for cylinder 6/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using the Active Test.
Av Engine Speed of All Cyl Engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using the Active Test.
A/F Sensor Determination (worst value) #1 Worst judgment value of air fuel ratio sensor output for bank 1/
Min.: -1, Max.: 0.99
0.00 -
A/F Sensor Determination (worst value) #2 Worst judgment value of air fuel ratio sensor output for bank 2/
Min.: -1, Max.: 0.99
0.00 -
Engine Speed Fluctuation Avg (worst value) #1 Worst value of average engine speed fluctuation (cylinder 1)/
Min.: 0, Max.: 2.55
0.00 -
Engine Speed Fluctuation Avg (worst value) #2 Worst value of average engine speed fluctuation (cylinder 2)/
Min.: 0, Max.: 2.55
0.00 -
Engine Speed Fluctuation Avg (worst value) #3 Worst value of average engine speed fluctuation (cylinder 3)/
Min.: 0, Max.: 2.55
0.00 -
Engine Speed Fluctuation Avg (worst value) #4 Worst value of average engine speed fluctuation (cylinder 4)/
Min.: 0, Max.: 2.55
0.00 -
Engine Speed Fluctuation Avg (worst value) #5 Worst value of average engine speed fluctuation (cylinder 5)/
Min.: 0, Max.: 2.55
0.00 -
Engine Speed Fluctuation Avg (worst value) #6 Worst value of average engine speed fluctuation (cylinder 6)/
Min.: 0, Max.: 2.55
0.00 -
SPD (NT) Input shaft speed/
Min.: 0 rpm, Max.: 12750 rpm
Lock-up is:
·

Lock-up on (after warming up engine): Input turbine speed (NT) equal to engine speed

·

Lock-up off (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed


Data is displayed in increments of 50 rpm.
SPD (SP2) Output shaft speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed) -
Overdrive Cut Switch #1 Status of the overdrive cut switch No.1/
ON or OFF
- -
Shift SW Status (P Range) PNP switch status (P)/
ON or OFF
·

Shift lever in P: ON

·

Shift lever not in P: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status (R)/
ON or OFF
·

Shift lever in R: ON

·

Shift lever not in R: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (N Range) PNP switch status (N)/
ON or OFF
·

Shift lever in N: ON

·

Shift lever not in N: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (N,P Range) Supported Status of park/neutral position switch (P or N) supported/
Unsupp or Supp
Supp -
Shift SW Status (N, P Range) PNP switch status (P or N)/
ON or OFF
·

Shift lever in P or N: ON

·

Shift lever not in P or N: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not in "-" (down-shift)


-
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Shift SW Status (D Range) PNP switch status (D)/
ON or OFF
·

Shift lever in D, S, "+" or "-": ON

·

Shift lever not in D, S, "+" or "-": OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
A/T Oil Temperature 1 No. 1 ATF temperature sensor value/
Min.: -40°C, Max.: 215.0°C
·

After stall test:

Approximately 80°C (176°F)

·

Equal to ambient temperature when engine cold


If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.
A/T Oil Temperature 2 No. 2 ATF temperature sensor value/
Min.: -40°C, Max.: 215.0°C
·

After stall test:

Approximately 80°C (176°F)

·

Equal to ambient temperature when engine cold


If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted.
ATF Thermal Degradation Estimate Estimated value of ATF thermal degradation/
Min.: 0
Max.: 65535
- If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the ATF.
Lock Up Lock-up/
ON or OFF
·

Lock-up operating: ON

·

Lock-up not operating: OFF


-
Shift Status ECM gear shift command/
1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th
·

Shift lever in D: 1st, 2nd, 3rd, 4th or 5th

·

Shift lever in S: 1st, 2nd, 3rd, 4th or 5th


-
SLT Solenoid Status Shift solenoid SLT status/
ON or OFF
·

Accelerator pedal depressed: OFF

·

Accelerator pedal released: ON


-
SLU Solenoid Status Shift solenoid SLU status/
ON or OFF
·

Shift solenoid operating: ON

·

Shift solenoid not operating: OFF


-
Torque Converter Temperature Raise History Torque converter temperature raise history status/
ON or OFF
OFF This item always displays OFF.

*: This excludes the throttle valve opening percentage due to Idle Speed Control (ISC).



HINT:

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in P or N, the A/C switch should be off and all accessory switches should be off.


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.

Tester Display Test Part Control Range Diagnostic Note
Control the Injection Volume Change injection volume Between -12.5% and 24.8%
·

All fuel injectors are tested at the same time.

·

Perform the test at or below 3000 rpm.

·

Injection volume can be changed in 1% gradations within control range.


Control the Injection Volume for A/F Sensor Change injection volume -12.5%/0%/12.5%
·

Perform the test at or below 3000 rpm.

·

Control the Injection Volume for A/F Sensor enables the checking and graphing of the air fuel ratio sensor voltage outputs.

·

To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S2.


Activate the VSV for Secondary Air Control Activate the secondary air system ON/OFF
·

Do not perform this test for 5 seconds or more.

·

After the test, do not perform the test again for 30 seconds.


Activate the VSV for Evap Control Activate purge VSV control ON/OFF -
Control the A/C Cut Signal Control A/C cut signal ON/OFF -
Control the Fuel Pump / Speed Activate fuel pump ON/OFF Perform this test with the engine stopped.
Control the Fuel Pump Duty Activate fuel pump 25%/80% This test is possible when the following conditions are met:
·

The ignition switch is ON.

·

The engine is not started.

·

The shift lever is in P.


Connect the TC and TE1 Turn on and off TC and TE1 connection ON/OFF
·

ON: TC and TE1 are connected.

·

OFF: TC and TE1 are disconnected.


Control the Idle Fuel Cut Prohibit Prohibit idling fuel cut control ON/OFF -
Prohibit the Catalyst OT Misfire prevent F/C Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire ON/OFF
ON: Fuel cut prohibited
Confirm that the vehicle is stopped and the engine speed is 3000 rpm or less.
Control the ETCS Open/Close Slow Speed Throttle actuator Close/Open
Open: Throttle valve opens slowly
This test is possible when the following conditions are met:
·

Ignition switch is ON.


·

Engine is stopped.


·

Accelerator pedal is fully depressed (APP: 58 degrees or more).

·

Shift lever in P.


Control the ETCS Open/Close Fast Speed Throttle actuator Close/Open
Open: Throttle valve opens quickly
Same as above.
Control the VVT Linear (Bank 1) Control Variable Valve Timing (VVT) [Bank 1] -128 to 127% (this value added to present camshaft timing oil control valve control duty)
100%: Maximum advance
-100%: Maximum retard
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%.

·

Perform this test when the following conditions are met:

·

Engine is idling.


·

Shift lever in P.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT System (Bank 1) Turn Oil Control Valve (OCV) on and off ON/OFF
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly is turned on.

·

Engine runs and idles normally when the camshaft timing oil control valve assembly is off.

·

Perform this test when the following conditions are met:

·

Engine is idling.


·

Shift lever in P.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT Linear (Bank 2) Control Variable Valve Timing (VVT) [Bank 2] -128 to 127% (this value added to present camshaft timing oil control valve control duty)
100%: Maximum advance
-100%: Maximum retard
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%.

·

Perform this test when the following conditions are met:

·

Engine is idling.


·

Shift lever in P.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT System (Bank 2) Turn Oil Control Valve (OCV) on and off ON/OFF
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly is turned on.

·

Engine runs and idles normally when the camshaft timing oil control valve assembly is off.

·

Perform this test when the following conditions are met:

·

Engine is idling.


·

Shift lever in P.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT Exhaust Linear (Bank 1) Control VVT (Bank 1) -128 to 127% (this value added to present camshaft timing oil control valve control duty)
100%: Maximum advance
-100%: Maximum retard
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%.

·

Perform this test when the following conditions are met:

·

Engine is idling.


·

Shift lever in P.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT Exhaust Linear (Bank 2) Control VVT (Bank 2) -128 to 127% (this value added to present camshaft timing oil control valve control duty)
100%: Maximum advance
-100%: Maximum retard
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%.

·

Perform this test when the following conditions are met:

·

Engine is idling.


·

Shift lever in P.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Activate the Vacuum Pump Activate vacuum pump (built into canister pump module) ON/OFF -
Activate the VSV for Vent Valve Activate vent valve (built into canister pump module) ON/OFF -
Activate the Air Pump Heater Activate air pump heater ON/OFF
·

This test activates the air pump heater for up to 60 seconds.

·

To protect the air pump heater, do not perform this test more than 4 times in a row.


Control the Select Cylinder Fuel Cut Selected cylinder (cylinder #1 to #6) injector fuel-cut #1/#2/#3/#4/#5/#6
ON/OFF
Test is possible while the vehicle is stopped and the engine is idling*1.
Control the All Cylinders Fuel Cut All cylinder fuel cut ON/OFF Perform this test when the following conditions are met:
·

Vehicle is stopped.

·

Engine is idling.

·

Shift lever in P.


Check the Cylinder Compression*2 Check the cylinder compression pressure ON/OFF Fuel injection and ignition stop in all cylinders.

NOTICE:
*1:
·

If the display of the Data List item Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.

·

If the display of the Data List item Catalyst OT MF F/C item is Avail, perform this Active Test as described below.

1.

Stop the engine, turn the ignition switch to ON and turn Control the Cylinder #1 Fuel Cut (to Control the Cylinder #6 Fuel Cut) ON.

2.

Start the engine.




HINT:

*2: When cranking the engine, the Active Test measures the speed of each cylinder.

In this Active Test, the fuel of all cylinders is cut and cranking occurs for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.


1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

HINT:

To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.


7.

While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

HINT:

After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.


8.

Fully open the throttle.

9.

Crank the engine for about 10 seconds.

10.

Monitor the engine speed (Engine Speed of Cyl #1 to #6) displayed on the GTS.

HINT:

At first, the GTS displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder's engine speed measurement will change to the actual engine speed.


NOTICE:
·

When Check the Cylinder Compression is OFF and the engine is cranked, the engine will start.

·

If Check the Cylinder Compression needs to be performed after it is turned ON and performed once, press Exit to return to the Active Test menu screen. Then perform Check the Cylinder Compression again.

·

Use a fully-charged battery.






SYSTEM CHECK


HINT:

Performing a system check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are stored, and can detect potential malfunctions in the system. The system check can be performed with the GTS.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility.


e.

Perform the system check by referring to the table below.

Tester Display Test Part Control Range Diagnostic Note
Secondary Air Injection Check
(Automatic Mode)
Perform secondary air injection system operation automatically With warm engine, ignition switch turned off once
·

If no pending DTCs are output after performing this test, the system is functioning normally.

·

Refer to the inspection procedure for secondary air injection system DTCs.

·

When performing Secondary Air Injection Check after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when System Check finishes.


Secondary Air Injection Check
(Manual Mode)
Perform 5 operations in order to operate secondary air injection system monitor manually With warm engine, ignition switch turned off once
·

Used to detect malfunctioning parts.

·

Refer to the inspection procedure for secondary air injection system DTCs.

·

When performing Secondary Air Injection Check after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when System Check finishes.