Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2014.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2431  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1  P2432  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1  P2433  Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1  P2436  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank 2  P2437  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank 2  P2438  Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank 2  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P0412).

Refer to DTC P0416 (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P0416).

DTC No. DTC Detection Condition Trouble Area
P2431
P2436
Pressure sensor indicates a value below 45.6 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) (2 trip detection logic).
·

NO.1 emission control valve set (for Bank 1)

·

NO.2 emission control valve set (for Bank 2)

·

Open or short in pressure sensor circuit

·

ECM


P2432
P2437
While the engine is running, the voltage output of the pressure sensor is below 0.5 V (1 trip detection logic).
·

NO.1 emission control valve set (for Bank 1)

·

NO.2 emission control valve set (for Bank 2)

·

Open or short in pressure sensor circuit

·

ECM


P2433
P2438
While the engine is running, the voltage output of the pressure sensor is higher than 4.5 V (1 trip detection logic).
·

NO.1 emission control valve set (for Bank 1)

·

NO.2 emission control valve set (for Bank 2)

·

Open or short in pressure sensor circuit

·

ECM



MONITOR DESCRIPTION

A334800E01
0.113,2.615 1.166,2.796 1.053,0.181 10 Pressure Sensor 2.526,2.829 2.852,3.010 0.326,0.181 10 ECM 2.27,0.722 2.671,0.903 0.401,0.181 10 VCV2 2.27,1.436 2.512,1.617 0.241,0.181 10 AIP 0.906,1.557 1.147,1.738 0.241,0.181 10 AIP 2.27,2.129 2.478,2.311 0.208,0.181 10 E2 0.945,0.88 1.155,1.062 0.210,0.181 10 VC 0.973,2.254 1.160,2.436 0.187,0.181 10 E2 0.034,0 2.107,0.225 2.073,0.225 10 Reference (for Bank 1):

The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the emission control valve set in the secondary air injection system. Using this pressure value, the ECM determines whether the secondary air injection system is malfunctioning or not.

If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the pressure sensor or circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the GTS initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the secondary air injection system pending codes: Press ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P2431, P2432, P2433, P2436, P2437 or P2438.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A334801E02
1.427,1.375 1.656,1.542 0.229,0.167 10 false VC 1.771,1.375 1.917,1.521 0.146,0.146 10 false 2 1.385,1.938 1.656,2.104 0.271,0.167 10 false AIP 5.76,1.344 6.167,1.51 0.406,0.167 10 false VCV2 5.76,1.927 6.031,2.094 0.271,0.167 10 false AIP 1.771,1.938 1.917,2.083 0.146,0.146 10 false 3 1.448,2.5 1.656,2.667 0.208,0.167 10 false E2 1.771,2.5 1.917,2.646 0.146,0.146 10 false 4 0.427,2.99 0.698,3.156 0.271,0.167 10 false B53 0.427,3.156 2.615,3.573 2.188,0.417 10 false NO. 1 Emission Control Valve Set 0.427,5.698 2.594,6.073 2.167,0.375 10 false NO. 2 Emission Control Valve Set 1.375,3.896 1.74,4.063 0.365,0.167 10 false VC2 1.771,3.896 1.917,4.042 0.146,0.146 10 false 2 1.323,4.458 1.656,4.625 0.333,0.167 10 false AIP2 1.771,4.458 1.917,4.604 0.146,0.146 10 false 3 1.354,5.021 1.656,5.188 0.302,0.167 10 false E22 1.771,5.021 1.917,5.167 0.146,0.146 10 false 4 0.427,5.531 0.698,5.698 0.271,0.167 10 false B54 5.458,1.281 5.635,1.458 0.177,0.177 10 false 16 5.417,1.479 5.708,1.635 0.292,0.156 10 false B36 5.49,1.854 5.667,2.031 0.177,0.177 10 false 1 5.417,2.042 5.708,2.198 0.292,0.156 10 false F51 5.76,4.438 6.104,4.604 0.344,0.167 10 false AIP2 5.51,4.375 5.688,4.552 0.177,0.177 10 false 2 5.417,4.573 5.708,4.729 0.292,0.156 10 false F51 5.76,4.979 6.24,5.146 0.479,0.167 10 false ETHA 6.156,5.99 6.531,6.156 0.375,0.167 10 false ECM 5.51,4.917 5.688,5.094 0.177,0.177 10 false 7 5.417,5.104 5.708,5.26 0.292,0.156 10 false B37

CAUTION / NOTICE / HINT

HINT:
·

Refer to "Data List / Active Test" [Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute)] (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the NO. 1 cylinder*.

*: The NO. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the NO. 1 cylinder.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EMISSION CONTROL VALVE SET - ECM)
a.

Disconnect the emission control valve set connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B53-3 (AIP) - F51-1 (AIP) Always Below 1 Ω
B53-2 (VC) - B36-16 (VCV2) Always Below 1 Ω
B53-4 (E2) - B37-7 (ETHA) Always Below 1 Ω
B54-3 (AIP2) - F51-2 (AIP2) Always Below 1 Ω
B54-2 (VC2) - B36-16 (VCV2) Always Below 1 Ω
B54-4 (E22) - B37-7 (ETHA) Always Below 1 Ω
B53-3 (AIP) or F51-1 (AIP) - Body ground Always 10 kΩ or higher
B53-2 (VC) or B36-16 (VCV2) - Body ground Always 10 kΩ or higher
B54-3 (AIP2) or F51-2 (AIP2) - Body ground Always 10 kΩ or higher
B54-2 (VC2) or B36-16 (VCV2) - Body ground Always 10 kΩ or higher



d.

Reconnect the emission control valve set connector.


e.

Reconnect the ECM connectors.



OK

2.CHECK TERMINAL VOLTAGE (VC OF EMISSION CONTROL VALVE SET)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (VC OF EMISSION CONTROL VALVE SET)
U180635E01
0.153,0.147 0.359,0.338 0.206,0.192 10 *a 0.248,0.886 0.536,1.049 0.288,0.163 10 B53 0.248,1.255 0.536,1.418 0.288,0.163 10 B54 0.675,0.864 0.876,1.038 0.201,0.173 10 *A 0.675,1.247 0.876,1.420 0.201,0.173 10 *B 0.871,1.676 1.249,1.832 0.378,0.156 10 VC*A 0.871,1.891 1.311,2.047 0.440,0.156 10 VC2*B 2.109,1.676 2.486,1.832 0.378,0.156 10 E2*A 2.109,1.891 2.549,2.047 0.440,0.156 10 E22*B 1.537,1.131 1.069,1.655 false 1.856,1.134 2.242,1.655 false

a.

Disconnect the emission control valve set connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B53-2 (VC) - B53-4 (E2) Ignition switch ON 4.5 to 5.5 V
B54-2 (VC2) - B54-4 (E22) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to Emission Control Valve Set)


d.

Reconnect the emission control valve set connector.



OK

3.REPLACE EMISSION CONTROL VALVE SET

NG

3.REPLACE EMISSION CONTROL VALVE SET
a.

Replace the emission control valve set.

HINT:
·

Replace the NO. 1 emission control valve set (See page Engine / Hybrid System>1GR-FE EMISSION CONTROL>AIR SWITCHING VALVE(for Bank 1)>REMOVAL).

·

Replace the NO. 2 emission control valve set (See page Engine / Hybrid System>1GR-FE EMISSION CONTROL>AIR SWITCHING VALVE(for Bank 2)>REMOVAL).





NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Perform the Confirmation Driving Pattern.

Result
Result Proceed to
NORMAL
(No DTC is output)
A
ABNORMAL
(P2431, P2432, P2433, P2436, P2437 or P2438 is output)
B



A

END

B