Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2014.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0416  Secondary Air Injection System Switching Valve "B" Circuit Open  P0417  Secondary Air Injection System Switching Valve "B" Circuit Shorted  


DESCRIPTION

The ECM operates the air injection VSV relay (AI-VSV) which causes the NO. 2 emission control valve to operate.

DTC No. DTC Detection Condition Trouble Area
P0416 Open or short in the air injection VSV relay (AI-VSV) circuit for 3 seconds (1 trip detection logic).
·

Open or short in air injection VSV relay (AI-VSV) circuit

·

Air injection VSV relay (AI-VSV)

·

ECM


P0417 Open or short in the air injection VSV relay (AI-VSV) circuit for 3 seconds (1 trip detection logic).
·

Open or short in air injection VSV relay (AI-VSV) circuit

·

Air injection VSV relay (AI-VSV)

·

ECM



MONITOR DESCRIPTION

These DTCs are designed to detect a malfunction in the air injection VSV relay (AI-VSV) circuit. When the system is normal, the battery voltage is applied to terminal AIR1 of the ECM while the air injection VSV relay (AI-VSV) is turned off, and the battery voltage is not applied to terminal AIR1 of the ECM while the air injection VSV relay (AI-VSV) is turned on. The ECM illuminates the MIL and stores a DTC when either one of the following conditions is detected.

·

The battery voltage is not applied to terminal AIR1 while the air injection VSV relay (AI-VSV) is off.

·

The battery voltage is applied to terminal AIR1 while the air injection VSV relay (AI-VSV) is on.


CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.

10.

Start the engine after the GTS initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the secondary air injection system pending codes: Press ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P0416 or P0417.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A288979E03
6.208,6.021 6.792,6.313 0.583,0.292 10 false ECM 3.115,5.042 5.333,5.354 2.219,0.313 10 false No. 2 Emission Control Valve Set 2.75,5.042 3.125,5.26 0.375,0.219 10 false B54 3.24,2.813 5.021,3.25 1.781,0.438 10 false Air Injection Control Driver 3.229,1.906 3.51,2.083 0.281,0.177 10 false A49 3.229,0.979 3.51,1.156 0.281,0.177 10 false A48 3.229,2.385 3.51,2.563 0.281,0.177 10 false A49 4.781,0.958 5.063,1.135 0.281,0.177 10 false A49 4.781,1.938 5.063,2.115 0.281,0.177 10 false A49 4.781,2.5 5.063,2.677 0.281,0.177 10 false A49 3.573,0.99 4,1.167 0.427,0.177 10 false BATT 3.573,1.917 4,2.094 0.427,0.177 10 false +B 3.323,1.74 3.479,1.917 0.156,0.177 10 false 5 3.323,0.792 3.479,0.969 0.156,0.177 10 false 1 3.313,2.188 3.469,2.365 0.156,0.177 10 false 1 3.573,2.385 4,2.563 0.427,0.177 10 false E 4.469,0.969 4.74,1.146 0.271,0.177 10 false SIV 4.854,0.781 5.01,0.958 0.156,0.177 10 false 3 4.469,1.927 4.74,2.104 0.271,0.177 10 false SIP 4.865,1.75 5.021,1.927 0.156,0.177 10 false 4 4.531,2.5 4.802,2.677 0.271,0.177 10 false DI 4.854,2.323 5.01,2.5 0.156,0.177 10 false 2 3.094,4.594 3.25,4.771 0.156,0.177 10 false 1 3.083,4 3.24,4.177 0.156,0.177 10 false 5 4.635,3.781 4.792,3.958 0.156,0.177 10 false 4 4.635,4.625 4.792,4.802 0.156,0.177 10 false 3 4.625,4.208 4.781,4.385 0.156,0.177 10 false 2 5.615,3.854 5.896,4.031 0.281,0.177 10 false B37 5.698,3.677 5.854,3.854 0.156,0.177 10 false 7 5.938,3.854 6.396,4.031 0.458,0.177 10 false ETHA 5.604,4.302 5.885,4.479 0.281,0.177 10 false B36 5.656,4.135 5.865,4.313 0.208,0.177 10 false 16 5.938,4.313 6.385,4.49 0.448,0.177 10 false VCV2 5.615,4.74 5.896,4.917 0.281,0.177 10 false F51 5.708,4.552 5.865,4.729 0.156,0.177 10 false 2 5.938,4.74 6.323,4.917 0.385,0.177 10 false AIP2 4.292,3.875 4.594,4.052 0.302,0.177 10 false E22 4.24,4.74 4.615,4.917 0.375,0.177 10 false AIP2 4.271,4.302 4.615,4.479 0.344,0.177 10 false VC2 3.281,4.073 3.708,4.25 0.427,0.177 10 false +BL 3.271,4.688 3.708,4.865 0.438,0.177 10 false GNDL 5.594,0.948 5.875,1.125 0.281,0.177 10 false B36 5.656,0.76 5.875,0.938 0.219,0.177 10 false 26 5.927,0.958 6.385,1.135 0.458,0.177 10 false AIRV 5.604,1.938 5.885,2.115 0.281,0.177 10 false B37 5.667,1.771 5.885,1.948 0.219,0.177 10 false 23 5.927,1.927 6.385,2.104 0.458,0.177 10 false AIRP 5.604,2.49 5.885,2.667 0.281,0.177 10 false B37 5.667,2.313 5.885,2.49 0.219,0.177 10 false 30 5.927,2.5 6.385,2.677 0.458,0.177 10 false AIDI 0.76,1.865 1.208,2.135 0.448,0.271 10 false ALT 1.917,2.385 2.667,2.896 0.75,0.51 10 false AIR PUMP HTR 1.719,3.094 1.875,3.271 0.156,0.177 10 false 5 1.49,3.875 1.646,4.052 0.156,0.177 10 false 2 1.875,3.885 2.031,4.063 0.156,0.177 10 false 3 1.323,3.104 1.479,3.281 0.156,0.177 10 false 1 2.177,3.49 2.833,3.896 0.656,0.406 10 false AI-VSV 0.625,1.156 1.323,1.531 0.698,0.375 10 false AIR PMP 0.74,4.854 1.344,5.063 0.604,0.208 10 false Battery 0.198,0.083 1.302,0.49 1.104,0.406 12 false for Bank 2: 5.615,5.542 5.896,5.719 0.281,0.177 10 false B38 5.667,5.354 5.906,5.531 0.24,0.177 10 false 21 5.938,5.542 6.323,5.719 0.385,0.177 10 false AIR1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AIR INJECTION VSV RELAY (AI-VSV)
a.

Inspect the air injection VSV relay (AI-VSV) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION).



OK

2.CHECK AIR INJECTION VSV RELAY (POWER SOURCE)

NG

REPLACE AIR INJECTION VSV RELAY (AI-VSV)

2.CHECK AIR INJECTION VSV RELAY (POWER SOURCE)
a.

Remove the air injection VSV relay (AI-VSV).


b.
A288679E01
1.264,0.393 1.534,0.590 0.270,0.197 10 *1 1.617,3.075 1.865,3.272 0.249,0.197 10 *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Air injection VSV relay (AI-VSV) terminal 1 - Body ground Ignition switch ON 11 to 14 V
Air injection VSV relay (AI-VSV) terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*1 Air Injection VSV Relay (AI-VSV)
*2 Engine Room Relay Block


c.

Reinstall the air injection VSV relay (AI-VSV).



OK

3.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION VSV RELAY)

NG

4.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - AIR INJECTION VSV RELAY)
3.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION VSV RELAY)
a.

Remove the air injection VSV relay (AI-VSV).


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Air injection VSV relay (AI-VSV) terminal 2 - B38-21 (AIR1) Always Below 1 Ω
Air injection VSV relay (AI-VSV) terminal 2 or B38-21 (AIR1) - Body ground Always 10 kΩ or higher



d.

Reinstall the air injection VSV relay (AI-VSV).


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - AIR INJECTION VSV RELAY)
a.

Remove the air injection VSV relay (AI-VSV).


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Air injection VSV relay (AI-VSV) terminal 1 - A49-5 (+B) Always Below 1 Ω
Air injection VSV relay (AI-VSV) terminal 1 or A49-5 (+B) - Body ground Always 10 kΩ or higher



d.

Reinstall the air injection VSV relay (AI-VSV).


e.

Reconnect the air injection control driver connector.



OK

5.CHECK AIR INJECTION CONTROL DRIVER (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK AIR INJECTION CONTROL DRIVER (POWER SOURCE CIRCUIT)

OK

6.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND)

OK

7.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL)

OK

NG