Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL TANK › 2009.08–2014.08
RM1440E _51 Engine / Hybrid System _056126 1GR-FE FUEL _0273894 FUEL TANK A

1GR-FE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77213B 1.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.
A220824E05
0.635,2.74 0.729,2.74 0.729,2.74 1.365,3.427 true 2.177,2.875 2.083,2.875 2.083,2.875 1.5,3.563 true 0.448,2.667 0.635,2.813 0.188,0.146 10 false *1 2.229,2.802 2.417,2.948 0.188,0.146 10 false *2

Install the fuel tank to filler pipe hose to the fuel tank.

Text in Illustration
*1 Fuel Tank Side Mark
*2 Hose Side Mark

HINT:

Align the fuel tank side mark with the hose side mark when installing the hose.



Hide 77643A 2.INSTALL NO. 3 FUEL TANK PROTECTOR

a.

Install the No. 3 fuel tank protector and attach the 4 clamps.


b.

Install the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 77020A 3.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.

Apply a light coat of gasoline or grease to a new gasket and install the gasket to the fuel tank.


b.
A220825E12
1.469,2.375 1.396,2.375 1.396,2.375 1.167,2.781 true 1.229,2.99 1.583,2.99 true 1.604,2.906 1.802,3.063 0.198,0.156 10 true *2 1.5,2.323 1.698,2.479 0.198,0.156 10 false *1

Install the fuel suction with pump and gauge tube into the fuel tank.

HINT:

Align the protrusion of the fuel suction with pump and gauge tube with the groove of the fuel tank.


Text in Illustration
*1 Protrusion
*2 Groove

NOTICE:

Be careful not to bend the arm of the fuel sender gauge.



c.

Put the new retainer on the fuel tank. While holding the fuel suction with pump and gauge tube, tighten the retainer one complete turn by hand.


d.
A220827E04
0.458,0.833 0.542,0.833 0.542,0.833 0.885,1.208 true 1.885,0.271 1.469,0.125 1.469,0.125 1.354,0.125 false 1.354,3.115 0.844,3.115 false 1.677,3.083 2.76,3.083 true 0.26,0.771 0.448,0.917 0.188,0.146 10 false *1 0.958,0.031 1.292,0.188 0.333,0.156 10 false SST 0.635,3.021 0.823,3.167 0.188,0.146 10 false *1 2.802,2.99 2.99,3.135 0.188,0.146 10 false *2 1.125,3.698 1.25,3.844 0.125,0.146 10 false A

Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank, as shown in the illustration.

SST
09808-14020  

Text in Illustration
*1 Fuel Tank Side Mark
*2 Retainer Side Mark

HINT:

Fit the tips of SST onto the ribs of the retainer.



Hide 77209D 4.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL RETURN TUBE SUB-ASSEMBLY

a.
A220829

Install the fuel tank main tube and fuel return tube with the 2 fuel tube joint clips.

NOTICE:
·
A118171E34
2.542,0.99 1.625,0.99 false 0.979,0.635 0.458,0.635 false 0.969,1.365 0.25,1.365 true 0.969,1.208 0.354,1.208 0.354,1.208 0.354,1.365 true 1.938,0.135 1.854,0.135 1.854,0.135 1.688,0.51 false 2.573,0.896 2.771,1.042 0.198,0.146 10 false *4 0.229,0.552 0.427,0.698 0.198,0.146 10 false *1 0.052,1.25 0.25,1.396 0.198,0.146 10 false *2 1.969,0.031 2.167,0.177 0.198,0.146 10 false *3 0.854,4.271 1.052,4.417 0.198,0.146 10 false *a 2.531,4.271 2.729,4.417 0.198,0.146 10 false *b

Check that there are no scratches or foreign objects on the connecting parts.

·

Check that the fuel tube joints are inserted securely.

·

Check that the fuel tube joint clips are on the collars of the fuel tube joints.

·

After installing the fuel tube joint clips, check that the fuel tube joints cannot be pulled off.

Text in Illustration
*1 Fuel Tube Joint
*2 O-Ring
*3 Fuel Tube
*4 Fuel Tube Joint Clip
*a CORRECT
*b INCORRECT




b.

Install the fuel tank main tube and fuel return tube to the fuel tank.


Hide 77651A 5.INSTALL FUEL TANK CUSHION

a.

Install 3 new fuel tank cushions to the fuel tank.


Hide 77100U 6.INSTALL FUEL TANK SUB-ASSEMBLY

a.

Set the fuel tank on a transmission jack and lift up the transmission jack.

NOTICE:

Do not allow the fuel tank to contact the vehicle, especially the differential.



b.

Install the 2 fuel tank bands with the 2 pins and 2 clips.


c.

Connect the 2 fuel tank bands with the 2 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 77213B 7.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.

Connect the fuel tank to filler pipe hose to the filler pipe.


Hide 8.CONNECT FUEL CUT OFF TUBE

a.

Connect the fuel cut off tube (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 77012 9.CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY

a.

Connect the fuel tank breather tube (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 77207A 10.CONNECT FUEL RETURN TUBE SUB-ASSEMBLY

a.

Connect the fuel return tube (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 77209D 11.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Connect the fuel tank main tube (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 77606 12.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.

for Half Cover Type:

Install the No. 1 fuel tank protector with the 4 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

for Standard Type:

Install the No. 1 fuel tank protector with the 6 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 58325E 13.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Connect the fuel pump and fuel sender gauge connector.


b.

Install the rear floor service hole cover with the 3 screws.


Hide 14.INSTALL REAR SEAT ASSEMBLY LH

a.

for 60/40 Split Double-folding Seat Type LH Side:

Install the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Double-folding Seat Type LH Side)>INSTALLATION).


b.

for 60/40 Split Slide Walk-in Seat Type LH Side:

Install the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type LH Side)>INSTALLATION).


Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).