Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Double-folding Seat Type LH Side)
RM1440E _58 Vehicle Interior _056161 SEAT _0274105 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Double-folding Seat Type LH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Double-folding Seat Type LH Side)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 72691B 1.INSTALL REAR SEAT CUSHION LOCK STRIKER

a.

Install the striker with the 2 bolts.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 72602B 2.INSTALL REAR NO. 2 SEATBACK LOCK STRIKER SUB-ASSEMBLY LH

B237984E04
0.167,1.719 0.396,1.906 0.229,0.188 10 true (1) 2.521,0.198 2.75,0.385 0.229,0.188 10 true (2)

a.

Attach the claw and install the striker with the 2 bolts.


b.

Tighten the bolts in the order indicated in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 64740C 3.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

Hide 64713F 4.INSTALL FRONT DECK SIDE TRIM COVER LH

Hide 64725J 5.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Hide 73233A 6.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

Hide 7.INSTALL REAR FLOOR CARPET ASSEMBLY (w/ Deck Board)

a.

Attach the 4 claws to install the rear floor carpet.


Hide 58570C 8.INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

Hide 58574A 9.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

Hide 58306A 10.INSTALL INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)

Hide 58410R 11.INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)

Hide 58704A 12.INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)

Hide 58703A 13.INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

Hide 58480B 14.INSTALL REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)

Hide 58408D 15.INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

Hide 64722B 16.INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board, w/o Rear No. 2 Seat)

HINT:

Use the same procedure for all No. 2 luggage compartment trim covers.


a.

Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.


b.

Attach the 2 claws to close the cover.


Hide 58401A 17.INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)

Hide 64721B 18.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)

Hide 62332C 19.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 72678 21.INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE LH

a.

Attach the cable clamp to connect the cable.


b.
B237982

Move the cover in the direction of the arrow to attach the 2 guides.


c.

Attach the 6 claws to install the lever base.


Hide 71304C 22.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH

a.

Install the hinge with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 23.INSTALL REAR SEATBACK ASSEMBLY LH

B240263E04
3.083,0.229 3.021,0.229 3.021,0.229 2.813,1.073 true 3.125,0.146 3.354,0.344 0.229,0.198 10 false *1 1.896,2.417 2.094,2.604 0.198,0.188 10 true (1) 2.125,2.938 2.323,3.125 0.198,0.188 10 true (2) 2.979,1.292 3.177,1.479 0.198,0.188 10 true (3)

a.

Fold down the seatback, set the seatback positioning wire on the hinge, and then temporarily install the bolt to the hinge.

Text in Illustration
*1 Positioning Wire

NOTICE:

Be careful not to damage the vehicle body.



b.

Restore the seatback to the upright position and temporarily install the seatback with the 2 bolts.


c.

Tighten the bolts in the order indicated in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 71890A 24.INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH

a.

for Plastic Seatback Board:

i.

Attach the 2 claws and 4 clips to install the carpet.


ii.

Attach the 3 claws and clip to install the carpet.



b.

for Seatback Board with Carpet:

Attach the 4 claws and 5 clips to install the carpet.


Hide 72996A 25.INSTALL REAR SEATBACK COVER

a.

Attach the 4 claws to install the cover.


b.

Restore the seatback to the upright position and lock it.


Hide 71940A 26.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the headrest.


Hide 27.INSTALL REAR SEAT CUSHION ASSEMBLY LH

B240248E05
0.646,1.615 0.854,1.802 0.208,0.188 10 false (1) 1.656,1.938 1.865,2.125 0.208,0.188 10 true (2)

a.

Temporarily install the seat cushion with the 2 bolts.


b.

Tighten the bolts in the order indicated in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


c.

Lock the seat cushion.


Hide 71639 28.INSTALL REAR SEAT CUSHION HINGE COVER LH

a.

Attach the 3 claws to install the cover.


Hide 71629 29.INSTALL REAR SEAT CUSHION HINGE COVER

a.

Attach the 3 claws to install the cover.