1.DISCHARGE FUEL SYSTEM PRESSURE
Discharge the fuel system pressure (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).
2.REMOVE REAR SEAT ASSEMBLY LH
for 60/40 Split Double-folding Seat Type LH Side:
Remove the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Double-folding Seat Type LH Side)>REMOVAL).
for 60/40 Split Slide Walk-in Seat Type LH Side:
Remove the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type LH Side)>REMOVAL).
58325E
3.REMOVE REAR FLOOR SERVICE HOLE COVER
Remove the 3 screws and rear floor service hole cover.
Disconnect the fuel pump and sender gauge connector.
77606
4.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
for Standard Type:
Remove the 6 bolts and No. 1 fuel tank protector.
for Half Cover Type:
Remove the 4 bolts and No. 1 fuel tank protector.
77209D
5.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disconnect the fuel tank main tube (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).
6.DRAIN FUEL
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Operate the fuel pump and drain the fuel from the fuel tank main tube.
Do not smoke or be near an open flame when working on the fuel system.
Secure good ventilation.
Keep gasoline away from rubber or leather parts.
7.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
77207A
8.DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY
Disconnect the fuel return tube (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).
9.DISCONNECT FUEL CUT OFF TUBE
Disconnect the fuel cut off tube (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).
77012
10.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY
Disconnect the fuel tank breather tube (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).
77213B
11.DISCONNECT FUEL TANK TO FILLER PIPE HOSE
Disconnect the fuel tank to filler pipe hose from the filler pipe.
77100U
12.REMOVE FUEL TANK SUB-ASSEMBLY
Place a transmission jack under the fuel tank.
Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.
Slowly lower the transmission jack slightly.
77651A
13.REMOVE FUEL TANK CUSHION
Remove the No. 1, No. 2 and No. 3 fuel tank cushions from the fuel tank.
| *1 | No. 1 Fuel Tank Cushion |
| *2 | No. 2 Fuel Tank Cushion |
| *3 | No. 3 Fuel Tank Cushion |
77209D
14.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL RETURN TUBE SUB-ASSEMBLY
Remove the 2 fuel tube joint clips and pull out the fuel tank main tube and fuel return tube.
| *1 | Fuel Tube |
| *2 | Fuel Tube Joint |
| *3 | Fuel Tube Joint Clip |
| *4 | O-Ring |
Remove any dirt and foreign matter on the fuel tube joint before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.
Remove the fuel tank main tube and fuel return tube from the fuel tank.
77020A
15.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
Using SST, loosen the retainer.
Fit the tips of SST onto the ribs of the retainer.
When the retainer is loosened, be careful as the pump and gauge tube will spring upward from the force of the spring.
Remove any foreign matter around the fuel suction with pump and gauge tube before this operation.
Remove the retainer.
Remove the fuel suction with pump and gauge tube assembly from the fuel tank.
Be careful not to bend the arm of the fuel sender gauge.
Remove the gasket from the fuel tank.
77643A
16.REMOVE NO. 3 FUEL TANK PROTECTOR
Remove the 2 bolts.
Detach the 4 clamps and remove the No. 3 fuel tank protector.
77213B
17.REMOVE FUEL TANK TO FILLER PIPE HOSE
Remove the fuel tank to filler pipe hose from the fuel tank.