Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL TANK › from 2014.08
RM1440E _51 Engine / Hybrid System _056126 1GR-FE FUEL _0273894 FUEL TANK A

1GR-FE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

a.

Discharge the fuel system pressure (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 2.REMOVE REAR SEAT ASSEMBLY LH

a.

for 60/40 Split Double-folding Seat Type LH Side:

Remove the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Double-folding Seat Type LH Side)>REMOVAL).


b.

for 60/40 Split Slide Walk-in Seat Type LH Side:

Remove the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type LH Side)>REMOVAL).


Hide 58325E 3.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A220797

Remove the 3 screws and rear floor service hole cover.


b.
A225438

Disconnect the fuel pump and sender gauge connector.


Hide 77606 4.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A220805

for Standard Type:

Remove the 6 bolts and No. 1 fuel tank protector sub-assembly.


b.
A224491

for Half Cover Type:

Remove the 4 bolts and No. 1 fuel tank protector sub-assembly.


Hide 77209D 5.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A220806

Disconnect the fuel tank main tube sub-assembly (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 6.DRAIN FUEL

a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

Operate the fuel pump and drain the fuel from the fuel tank main tube.

CAUTION:
·

Do not smoke or be near an open flame when working on the fuel system.

·

Secure good ventilation.

·

Keep gasoline away from rubber or leather parts.




Hide 7.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 77207A 8.DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY

a.
A223269

Disconnect the fuel return tube sub-assembly (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 9.DISCONNECT FUEL CUT OFF TUBE (w/o Secondary Air Injection System)

a.
A220810

Disconnect the fuel cut off tube (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 77012 10.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (w/o Secondary Air Injection System)

a.
A223270

Disconnect the fuel tank breather tube sub-assembly (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 77404 11.DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY (w/ Secondary Air Injection System)

a.
A225443

Disconnect the fuel tank vent hose sub-assembly (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 77012 12.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (w/ Secondary Air Injection System)

a.
A227934

Disconnect the fuel tank breather tube sub-assembly (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 77213B 13.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A334235E02
0.104,0.083 0.448,0.427 0.344,0.344 12 false *A: 0.104,2.365 0.448,2.708 0.344,0.344 12 false *B:

Disconnect the fuel tank to filler pipe hose from the filler pipe.

Text in Illustration
*A w/o Secondary Air Injection System
*B w/ Secondary Air Injection System


Hide 77100U 14.REMOVE FUEL TANK SUB-ASSEMBLY

a.

Place a transmission jack under the fuel tank.


b.
A220832

Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.


c.

Slowly lower the transmission jack slightly.


Hide 77651A 15.REMOVE FUEL TANK CUSHION

a.
A220812E02
0.885,0.313 0.979,0.313 0.979,0.313 1.177,0.854 false 2.438,0.26 2.531,0.26 2.531,0.26 2.729,0.802 false 2.25,2.021 2.333,2.021 2.333,2.021 2.542,1.677 false 0.677,0.229 0.865,0.375 0.188,0.146 10 false *1 2.25,0.177 2.438,0.323 0.188,0.146 10 false *2 2.052,1.938 2.24,2.083 0.188,0.146 10 false *3

Remove the No. 1, No. 2 and No. 3 fuel tank cushions from the fuel tank.

Text in Illustration
*1 No. 1 Fuel Tank Cushion
*2 No. 2 Fuel Tank Cushion
*3 No. 3 Fuel Tank Cushion


Hide 77641A 16.REMOVE NO. 1 FUEL TANK PROTECTOR (w/ Secondary Air Injection System)

a.
A232961

Remove the No. 1 fuel tank protector from the fuel tank.


Hide 77012 17.REMOVE FUEL TANK BREATHER TUBE SUB-ASSEMBLY (w/ Secondary Air Injection System)

a.
A227935

Remove the fuel tank breather tube sub-assembly (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 77209D 18.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL RETURN TUBE SUB-ASSEMBLY

a.
A220814E03
2.323,2.969 2.229,2.969 2.229,2.969 2.031,3.26 false 1.167,2.958 1.271,2.958 1.271,2.958 1.458,3.25 false 2.521,3.292 2.417,3.292 2.417,3.292 2.229,3.583 false 1.698,3.948 1.167,3.948 true 1.698,3.833 1.271,3.833 1.271,3.833 1.271,3.948 true 2.365,2.896 2.552,3.042 0.188,0.146 10 false *2 0.969,2.885 1.156,3.031 0.188,0.146 10 false *1 2.573,3.219 2.76,3.365 0.188,0.146 10 false *3 0.958,3.865 1.146,4.01 0.188,0.146 10 false *4

Remove the 2 fuel tube joint clips and pull out the fuel tank main tube and fuel return tube.

Text in Illustration
*1 Fuel Tube
*2 Fuel Tube Joint
*3 Fuel Tube Joint Clip
*4 O-Ring

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




b.
A220818

Remove the fuel tank main tube and fuel return tube from the fuel tank.


Hide 77020A 19.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.
A220821E01
1.386,0.216 1.713,0.368 0.327,0.152 10 SST 2.418,0.305 1.771,0.305 false

Using SST, loosen the retainer.

SST
09808-14020  

HINT:

Fit the tips of SST onto the ribs of the retainer.


NOTICE:
·

When the retainer is loosened, be careful as the pump and gauge tube will spring upward from the force of the spring.

·

Remove any foreign matter around the fuel suction with pump and gauge tube before this operation.




b.

Remove the retainer.


c.

Remove the fuel suction with pump and gauge tube assembly from the fuel tank.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge.



d.

Remove the gasket from the fuel tank.


Hide 77643A 20.REMOVE NO. 3 FUEL TANK PROTECTOR

a.
A220823

Remove the 2 bolts.


b.

Detach the 4 clamps and remove the No. 3 fuel tank protector.


Hide 77213B 21.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A334236E02
0.125,0.115 0.667,0.469 0.542,0.354 12 false *A: 0.125,2.302 0.656,2.646 0.531,0.344 12 false *B:

Remove the fuel tank to filler pipe hose from the fuel tank.

Text in Illustration
*A w/o Secondary Air Injection System
*B w/ Secondary Air Injection System