Home › Engine / Hybrid System › 1GR-FE INTAKE / EXHAUST › EXHAUST PIPE › 2009.08–2013.08
RM1440E _51 Engine / Hybrid System _056128 1GR-FE INTAKE / EXHAUST _0273908 EXHAUST PIPE A

1GR-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 89465 1.INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 89465 2.INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

Hide 17450B 3.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

a.

Install 2 new gaskets and the No. 2 front exhaust pipe to the exhaust manifold with 2 new nuts.

Torque:
54 N*m (554 kgf*cm, 40 ft.*lbf)


b.

Connect the heated oxygen sensor connector.


Hide 17548 4.INSTALL EXHAUST PIPE STOPPER BRACKET

a.

Install the stopper bracket with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 17410 5.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

43 mm (1.69 in.)


If the free length is less than the minimum, replace the compression spring.



b.
A076194E30
2.031,1.583 1.531,1.708 1.531,1.708 1.385,1.708 true 2.396,0.969 3,0.969 true 1.156,1.625 1.375,1.802 0.219,0.177 10 false *1 3.063,0.885 3.281,1.063 0.219,0.177 10 false *2

Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front exhaust pipe.

Text in Illustration
*1 Gasket
*2 Wooden Block

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the exhaust pipe, do not push in the gasket with the exhaust pipe.




c.

Install a new gasket and the front exhaust pipe to the exhaust manifold with 2 new nuts.

Torque:
54 N*m (554 kgf*cm, 40 ft.*lbf)


d.

Connect the front exhaust pipe to the front No. 2 exhaust pipe with the 2 bolts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


e.

Connect the heated oxygen sensor connector.


Hide 17420 6.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

Connect the center exhaust pipe to the 3 exhaust pipe supports.


b.

Install the center exhaust pipe with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17430 7.INSTALL TAILPIPE ASSEMBLY

a.

Install the tailpipe to the exhaust pipe support.


b.

Set a new gasket to the center exhaust pipe.


c.

Install the 2 bolts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


Hide 52185A 8.INSTALL REAR BUMPER SIDE BRACKET RH (for X-Runner)

a.

Install the rear bumper side bracket RH with the 3 screws and clip.


Hide 52185A 9.INSTALL REAR BUMPER SIDE BRACKET RH

a.

Install the rear bumper side bracket RH with the 3 screws and clip.


Hide 76625G 10.INSTALL REAR QUARTER PANEL MUDGUARD RH (for X-Runner)

Hide 76625G 11.INSTALL REAR QUARTER PANEL MUDGUARD RH

Hide 12.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.