Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.
51457F
1.REMOVE ENGINE UNDER COVER SEAL
Remove the 2 bolts and engine under cover seal.
53298
2.REMOVE COOL AIR INTAKE DUCT (for 4WD with TOYOTA Parking Assist-sensor System)
52129B
3.DISCONNECT FRONT BUMPER LOWER COVER
Remove the 2 bolts and clip, and disconnect the front bumper lower cover.
51405A
4.DISCONNECT NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Remove the 4 bolts and open the No. 1 engine under cover sub-assembly as shown in the illustration.
5.DRAIN ENGINE OIL
Remove the oil filler cap.
Remove the oil pan drain plug and drain the engine oil into a container.
Install a new gasket and the oil pan drain plug.
6.REMOVE OIL FILTER ELEMENT
Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
| *1 | Pipe |
| *2 | Hose |
Remove the oil filter drain plug.
Install the pipe to the oil filter cap.
| *1 | Cap |
| *2 | Valve |
| *3 | Pipe |
| *4 | O-Ring |
| *5 | Hose |
If the O-ring is removed with the drain plug, install the O-ring together with the pipe.
Use a container to catch the draining oil.
Check that oil is drained from the oil filter. Then, disconnect the pipe and remove the O-ring as shown in the illustration.
Using SST, remove the oil filter cap.
| *1 | Oil Filter Bracket Clip |
Do not remove the oil filter bracket clip.
Remove the oil filter element and O-ring from the oil filter cap.
| *1 | O-Ring |
Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.
7.INSTALL OIL FILTER ELEMENT
Clean the inside of the oil filter cap, the threads and O-ring groove.
Apply a small amount of engine oil to a new O-ring and install the O-ring to the oil filter cap.
| *1 | O-ring |
| *a | CORRECT |
| *b | INCORRECT |
Be sure to install the O-ring in the proper location, otherwise oil may leak.
Do not twist the O-ring.
Set a new oil filter element on the oil filter cap.
Remove any dirt or foreign matter from the installation surface of the engine.
Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.
Do not pinch the O-ring for the cap.
Using SST, tighten the oil filter cap.
| *1 | Oil Filter Cap Assembly |
| *2 | O-ring |
| *3 | Oil Filter Bracket |
| *4 | Oil Filter Bracket Clip |
| *a | No gap |
After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.
When tightening the oil filter cap, do not remove the oil filter bracket clip.
Apply a small amount of engine oil to a new drain plug O-ring and install the O-ring to the oil filter cap.
| *1 | O-Ring |
Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.
Install the oil filter drain plug.
Make sure that the O-ring does not get caught between the parts.
8.ADD ENGINE OIL
Add fresh engine oil.
Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.
If engine oil is on the location indicated by the arrow, replace the belt tensioner.
| Oil Grade | Oil Viscosity (SAE) |
|---|---|
| API grade SL "energy-conserving", SM "energy-conserving" or ILSAC multigrade engine oil | 0W-20
5W-20 5W-30 10W-30 |
| API grade SL or SM multigrade engine oil | 15W-40
20W-50 |
| Item | Specified Condition |
|---|---|
| Drain and refill without oil filter change | 5.7 liters (6.0 US qts, 5.0 Imp. qts) |
| Drain and refill with oil filter change | 6.2 liters (6.6 US qts, 5.5 Imp. qts) |
| Dry fill | 7.1 liters (7.5 US qts, 6.2 Imp. qts) |
Install the oil filler cap.
9.CHECK ENGINE OIL LEVEL
10.INSPECT FOR ENGINE OIL LEAK
Start the engine. Make sure that there are no oil leaks from the area that was worked on.
51405A
11.CONNECT NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Close the No. 1 engine under cover sub-assembly with the 4 bolts.
52129B
12.CONNECT FRONT BUMPER LOWER COVER
Connect the front bumper lower cover with the 2 bolts and clip.
53298
13.INSTALL COOL AIR INTAKE DUCT (for 4WD with TOYOTA Parking Assist-sensor System)
51457F
14.INSTALL ENGINE UNDER COVER SEAL
Install the engine under cover seal with the 2 bolts.