Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2013.08
RM1440E _51 Engine / Hybrid System _056132 CRUISE CONTROL _0273923 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Stop Light Switch Circuit Malfunction  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. Upon receiving the signal, the ECM cancels cruise control. Even if there is a malfunction in the stop light signal circuit while cruise control is in operation, normal driving is maintained due to a fail-safe function.

When the brake pedal is depressed, positive voltage is applied to terminal STP of the ECM through the STOP fuse and stop light switch assembly, and the ECM cancels cruise control.

DTC Code DTC Detection Condition Trouble Area
P0571 The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more.
·

Stop light switch circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

A261062E05
6.188,2.333 6.74,2.625 0.552,0.292 10 false ECM 5.979,1.729 6.531,2.021 0.552,0.292 10 false ST1- 5.979,1.125 6.531,1.417 0.552,0.292 10 false STP 4.708,1.729 4.917,2.021 0.208,0.292 10 false L 4.708,1.135 4.917,1.427 0.208,0.292 10 false L 3.792,1.135 4,1.427 0.208,0.292 10 false B 3.604,1.042 3.813,1.333 0.208,0.292 10 false 7 3.792,1.49 4,1.781 0.208,0.292 10 false B 3.604,1.396 3.813,1.688 0.208,0.292 10 false 6 3.792,1.823 4.219,2.115 0.427,0.292 10 false GND 2.146,1.302 2.625,1.563 0.479,0.26 10 false STOP 0.385,1.146 1.229,1.573 0.844,0.427 10 false from Battery 0.208,1.49 1.229,1.917 1.021,0.427 10 false from IG2 Relay 2.219,1.656 2.698,1.917 0.479,0.26 10 false IGN 3.604,1.74 3.813,2.031 0.208,0.292 10 false 2 4.906,1.042 5.115,1.333 0.208,0.292 10 false 3 4.906,1.615 5.115,1.906 0.208,0.292 10 false 5 5.635,1.146 5.979,1.396 0.344,0.25 10 false F50 5.656,0.958 5.938,1.188 0.281,0.229 10 false 18 5.635,1.74 5.979,1.99 0.344,0.25 10 false F51 3.74,2.188 4.083,2.438 0.344,0.25 10 false A41 3.74,2.344 4.99,3 1.25,0.656 10 false Stop Light Switch Assembly 5.708,1.552 5.99,1.781 0.281,0.229 10 false 8

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)
a.
U181073E01
1.531,0.291 1.851,0.494 0.321,0.204 10 A41 0.18,0.156 0.333,0.312 0.152,0.156 10 *a 0.988,1.72 1.317,1.876 0.329,0.156 10 GND 1.351,1.19 1.179,1.699 false 2.518,1.72 2.633,1.876 0.115,0.156 10 B 2.211,1.19 2.52,1.699 false 2.174,1.72 2.289,1.876 0.115,0.156 10 B 2.05,1.19 2.221,1.699 false

Disconnect the A41 stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A41-6 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A41-7 (B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-2 (GND) - Body ground Always Below 1 Ω




OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the A41 stop light switch assembly connector.


b.

Disconnect the F50 and F51 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-3 (L) - F50-18 (STP) Always Below 1 Ω
A41-5 (L) - F51-8 (ST1-)
A41-3 (L) - Body ground Always 10 kΩ or higher
A41-5 (L) - Body ground




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR