Home › Drivetrain › A750E AUTOMATIC TRANSMISSION / TRANSAXLE › SHIFT LEVER
RM1440E _52 Drivetrain _056133 A750E AUTOMATIC TRANSMISSION / TRANSAXLE _0273930 SHIFT LEVER G

A750E AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK SHIFT LOCK OPERATION

a.

Move the shift lever to P.


b.

Turn the ignition switch off.


c.

Check that the shift lever cannot be moved from P.


d.

Turn the ignition switch to ON, depress the brake pedal and check that the shift lever can be moved to other positions.

If the operation cannot be performed as specified, inspect the transmission floor shift assembly and shift lock control ECU.


Hide 2.CHECK SHIFT LOCK RELEASE BUTTON OPERATION

a.

When operating the shift lever with the shift lock release button pressed, check that the lever can be moved to any position.

If the operation cannot be performed as specified, check the transmission floor shift assembly.


Hide 85903 3.CHECK SHIFT LOCK CONTROL ECU

U150236E02
2.146,1.135 2.531,0.75 false 1.604,1.156 1.219,0.771 true 1.625,1.406 1.229,1.833 false 0.24,0.99 0.531,1.177 0.292,0.188 10 false F75 2.552,0.573 3.031,0.979 0.479,0.406 10 true 1 (E) 0.729,0.573 1.219,0.917 0.49,0.344 10 true 4 (STP) 0.896,1.865 1.354,2.083 0.458,0.219 10 true 8 (IG)

a.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Do not disconnect the shift lock control ECU connector.


Standard Voltage and resistance:
Tester Connection Condition Specified Condition
F75-8 (IG) - F75-1 (E) Ignition switch ON 11 to 14 V
F75-8 (IG) - F75-1 (E) Ignition switch off Below 1 V
F75-4 (STP) - F75-1 (E) Brake pedal depressed 11 to 14 V
F75-4 (STP) - F75-1 (E) Brake pedal released Below 1 V
F75-1 (E) - Body ground Always Below 1 Ω



b.
C217000E01
0.104,0.065 0.304,0.274 0.200,0.209 10 *a 2.631,0.137 3.057,0.314 0.427,0.177 10 SLS+ 1.205,0.137 1.582,0.314 0.377,0.177 10 SLS- 2.308,0.925 2.58,0.284 false 1.922,0.925 1.65,0.284 false

Disconnect the shift lock solenoid connector from the shift lock control ECU.


c.

Measure the voltage according to the value(s) in the table below.

HINT:

Do not disconnect the shift lock control ECU connector.


Standard Voltage:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Ignition switch off Below 1 V
1 (SLS+) - 2 (SLS-) Ignition switch ON Below 1 V
Ignition switch ON and brake pedal depressed 11 to 14 V


Text in Illustration
*a Component without harness connected
(Shift Lock Control ECU)

If the result is not as specified, replace the transmission floor shift assembly.


Hide 85431 4.CHECK SHIFT LOCK SOLENOID

C217001E04
1.198,1.156 1.01,0.49 true 1.563,1.156 1.74,0.49 true 1.865,1.427 1.729,1.865 true 2.24,1.438 2.375,1.865 true 1.146,1.198 1.406,1.49 0.26,0.292 12 false 1 1.5,1.198 1.719,1.427 0.219,0.229 12 false 2 1.844,1.198 2.031,1.417 0.188,0.219 12 false 3 2.188,1.198 2.406,1.448 0.219,0.25 12 false 4 0.125,0.021 0.385,0.271 0.26,0.25 10 false *a 0.583,0.313 1.052,0.531 0.469,0.219 10 false SLS+ 1.74,0.271 2.208,0.49 0.469,0.219 10 false SLS- 2.385,1.906 2.542,2.094 0.156,0.188 10 false P 1.594,1.906 1.833,2.094 0.24,0.188 10 false E2

a.

Disconnect the shift lock solenoid connector from the shift lock control ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 101 to 123 Ω
3 (E2) - 4 (P) Shift lever in P 10 kΩ or higher
3 (E2) - 4 (P) Shift lever not in P Below 1 Ω


Text in Illustration
*a Component without harness connected:
(Shift Lock Control Solenoid)


c.

Apply 12 V of battery voltage to the shift lock solenoid and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Terminal 1 (SLS+)

·

Battery negative (-) → Terminal 2 (SLS-)


Solenoid moves and makes an operating noise


If the result is not as specified, replace the transmission floor shift assembly.