Home › Drivetrain › A750E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT
RM1440E _52 Drivetrain _056133 A750E AUTOMATIC TRANSMISSION / TRANSAXLE _0273934 AUTOMATIC TRANSMISSION UNIT G

A750E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  INSPECTION  


PROCEDURE

Hide 35106 1.INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

a.

Remove the magnets and use them to collect steel particles.


b.

Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

·

Steel (magnetic): bearing, gear and clutch plate wear

·

Brass (non-magnetic): bush wear



Hide 35790 2.INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY

D224379

a.

Hold the reverse clutch hub and turn the 1-way clutch assembly.


b.

Check that the 1-way clutch turns freely when turned clockwise and locks when turned counterclockwise.

Text in Illustration
V100135

Lock
V100136

Free


Hide 35677C 3.INSPECT REAR CLUTCH DISC

C171511

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



Hide 35049 4.INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY

D028000

a.

Using a dial indicator, measure the inside diameter of the reverse clutch hub bush.

Standard inside diameter:

35.812 to 35.837 mm (1.410 to 1.411 in.)


Maximum inside diameter:

35.887 mm (1.413 in.)


If the inside diameter is more than the maximum, replace the reverse clutch hub.



Hide 35061 5.INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY

D028501

a.

Using a dial indicator, measure the inside diameter of the forward clutch hub bush.

Standard inside diameter:

26.037 to 26.062 mm (1.025 to 1.026 in.)


Maximum inside diameter:

26.112 mm (1.028 in.)


If the inside diameter is more than the maximum, replace the forward clutch hub.



Hide 35633B 6.INSPECT FORWARD MULTIPLE DISC CLUTCH DISC

C171513

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



Hide 35603A 7.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

C171515

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

26.74 mm (1.05 in.)



Hide 35667A 8.INSPECT DIRECT CLUTCH DISC

C171512

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



Hide 35047 9.INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

C171517

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

21.04 mm (0.828 in.)



Hide 35604 10.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

C171516

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

19.51 mm (0.768 in.)



Hide 11.INSPECT NO. 3 BRAKE DISC

C161778

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



Hide 35046 12.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C171518

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

15.72 mm (0.619 in.)



Hide 35720 13.INSPECT FRONT PLANETARY GEAR ASSEMBLY

D028544

a.

Using a feeler gauge, measure the front planetary pinion gear thrust clearance.

Standard clearance:

0.2 to 0.6 mm (0.00787 to 0.0236 in.)


Maximum clearance:

0.65 mm (0.0256 in.)


If the clearance is more than the maximum, replace the front planetary gear assembly.



b.
D028543

Using a cylinder gauge, measure the inside diameter of the front planetary gear bush.

Maximum inside diameter:

57.48 mm (2.26 in.)


If the inside diameter is more than the maximum, replace the front planetary gear.



Hide 35790 14.INSPECT 1-WAY CLUTCH ASSEMBLY

D224380

a.

Install the 1-way clutch to the 1-way clutch inner race.

Text in Illustration
V100135

Lock
V100136

Free


b.

Hold the 1-way clutch inner race and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely when turned counterclockwise and locks when turned clockwise.


c.

Remove the 1-way clutch from the 1-way clutch inner race.


Hide 35681A 15.INSPECT NO. 1 BRAKE DISC

C171514

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



Hide 35608J 16.INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C171519

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

17.05 mm (0.671 in.)



Hide 35682A 17.INSPECT NO. 2 BRAKE DISC

C161770

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



Hide 35045 18.INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C171520

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

17.45 mm (0.687 in.)



Hide 35750 19.INSPECT CENTER PLANETARY GEAR ASSEMBLY

D028533

a.

Using a feeler gauge, measure the center planetary pinion gear thrust clearance.

Standard clearance:

0.12 to 0.68 mm (0.00472 to 0.0268 in.)


Maximum clearance:

0.73 mm (0.0287 in.)


If the clearance is more than the maximum, replace the center planetary gear assembly.



Hide 35770C 20.INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY

D224381

a.

Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely when turned counterclockwise and locks when turned clockwise.

Text in Illustration
V100135

Lock
V100136

Free


Hide 35077D 21.INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

D028531

a.

Using a dial indicator, measure the inside diameter of the rear planetary ring gear bush.

Standard inside diameter:

32.176 to 32.201 (1.267 to 1.268 in.)


Maximum inside diameter:

32.251 mm (1.270 in.)


If the inside diameter is more than the maximum, replace the rear planetary ring gear.



Hide 35713 22.INSPECT INTERMEDIATE SHAFT

U150403

a.

Using a dial indicator, measure the intermediate shaft runout.

Standard runout:

0.03 mm (0.00118 in.)


Maximum runout:

0.08 mm (0.00315 in.)


If the runout is more than the maximum, replace the intermediate shaft with a new one.


b.
D224382E01
0.708,3.031 0.865,3.229 0.156,0.198 10 false A 1.396,3.01 1.552,3.208 0.156,0.198 10 false B 1.938,3 2.094,3.198 0.156,0.198 10 false C 2.271,3.01 2.427,3.208 0.156,0.198 10 false D

Using a micrometer, measure the diameter of the intermediate shaft at the positions shown in the diagram.

Standard diameter:
A, B:

25.962 to 25.975 mm (1.022 to 1.023 in.)

C, D:

32.062 to 32.075 mm (1.262 to 1.263 in.)


Minimum diameter:
A, B:

25.912 mm (1.02 in.)

C, D:

32.012 mm (1.26 in.)


If the diameter is less than the minimum, replace the intermediate shaft with a new one.


Hide 35684 23.INSPECT NO. 4 BRAKE DISC

C161745

a.

Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

NOTICE:

When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



Hide 35760 24.INSPECT REAR PLANETARY GEAR ASSEMBLY

C190073

a.

Using a feeler gauge, measure the rear planetary pinion gear thrust clearance.

Standard clearance:

0.2 to 0.6 mm (0.00787 to 0.0236 in.)


Maximum clearance:

0.65 mm (0.0256 in.)


If the clearance is more than the maximum, replace the planetary gear assembly.



b.
C190074

Using a dial indicator, measure the inside diameter of the rear planetary gear bush.

Maximum inside diameter:

20.075 mm (0.790 in.)


If the inside diameter is more than the maximum, replace the rear planetary gear assembly.



Hide 35068 25.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C171521

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

23.74 mm (0.935 in.)



Hide 26.INSPECT 1ST AND REVERSE BRAKE

D027966

a.

Make sure the 1st and reverse brake piston moves smoothly when applying compressed air into and releasing compressed air from the transmission case.


Hide 27.INSPECT NO. 1 BRAKE

D028814

a.

Make sure the No. 1 brake piston moves smoothly when applying compressed air into and releasing compressed air from the transmission case.


Hide 28.INSPECT INDIVIDUAL PISTON OPERATION

a.
D224383E01
0.646,0.948 0.51,0.333 false 1.104,0.833 1.167,0.333 false 1.854,4.031 2.792,4.031 false 0.406,4.042 1.479,4.042 false 1.635,3.115 2.823,3.135 false 1.635,2.719 2.854,2.75 false 1.635,2.302 2.875,2.333 false 2.51,1.031 2.844,1.031 false 2.854,3.948 3.333,4.344 0.479,0.396 10 false B4 (OUT) 0.104,3.958 0.438,4.375 0.333,0.417 10 false B4 (IN) 0.271,0.24 0.583,0.438 0.313,0.198 10 false C2 1.24,0.24 1.552,0.438 0.313,0.198 10 false C1 2.885,0.938 3.198,1.135 0.313,0.198 10 false C3 2.917,2.229 3.229,2.427 0.313,0.198 10 false B3 2.906,2.667 3.219,2.865 0.313,0.198 10 false B1 2.885,3.042 3.198,3.24 0.313,0.198 10 false B2

Check the operating sound while applying compressed air into the oil holes indicated in the illustration.

HINT:

When inspecting the O/D direct clutch, check with the C3 accumulator piston hole closed.

If there is no sound, disassemble and check the installation condition of the parts.


1.

No. 2 clutch (C2)

2.

No. 3 clutch (C3)

3.

No. 1 clutch (C1)

4.

No. 3 brake (B3)

5.

No. 1 brake (B1)

6.

No. 2 brake (B2)

7.

No. 4 brake (B4)