Home › Drivetrain › A750E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1440E _52 Drivetrain _056133 A750E AUTOMATIC TRANSMISSION / TRANSAXLE _0273938 AUTOMATIC TRANSMISSION SYSTEM C

A750E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0722  Output Speed Sensor Circuit No Signal  


DESCRIPTION

The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the ECM. The ECM determines the vehicle speed based on these signals. An AC voltage is generated in the speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.

The gear shift point and lock-up timing are controlled by the ECM based on the signals from this vehicle speed sensor and the throttle position sensor signal.

DTC Code DTC Detection Condition Trouble Area
P0722 All conditions are met 500 times or more continuously (2-trip detection logic):
(a) No signal from speed sensor SP2 is input to the ECM while 4 pulses of the No. 1 vehicle speed sensor signal are sent.
(b) Vehicle speed is 9 km/h (6 mph) or more for at least 5 sec.
(c) Park/neutral position switch is OFF.
·

Open or short in speed sensor SP2 circuit

·

Speed sensor SP2

·

ECM

·

Automatic transmission (clutch, brake, gear, etc.)



C161208E01
2.708,0.198 3.292,0.396 0.583,0.198 10 false 2 V/DIV. 3,0.969 3.354,1.167 0.354,0.198 10 false GND 1.583,1.76 2.479,1.958 0.896,0.198 10 false 20 msec./DIV.

Reference: Inspect using an oscilloscope.

Check the waveform of the ECM connector.

Standard:
Terminal No. (Symbol) Tool Setting Condition Specified Condition
B38-9 (SP2+) - B38-10 (SP2-) 2 V/DIV., 20 msec./DIV. Vehicle speed 20 km/h (12 mph) Refer to illustration



MONITOR DESCRIPTION

The output speed sensor SP2 monitors the output shaft speed. The ECM controls the gear shift point and lock-up timing based on the signals from the output speed sensor SP2 and throttle position sensor.

If the ECM detects no signal from the output shaft speed sensor SP2 even while the vehicle is moving, it will conclude that there is a malfunction of the output speed sensor SP2. The ECM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

C361836E02
0.625,2.5 2.917,2.698 2.292,0.198 10 false Speed Sensor SP2 0.625,2.333 1.083,2.531 0.458,0.198 10 false B33 5.792,3.052 6.25,3.25 0.458,0.198 10 false B38 5.792,3.219 6.25,3.417 0.458,0.198 10 false ECM 1.26,2.083 1.417,2.281 0.156,0.198 10 false 2 1.26,1.26 1.417,1.458 0.156,0.198 10 false 1 5.385,1.25 5.542,1.448 0.156,0.198 10 false 9 5.333,2.385 5.542,2.583 0.208,0.198 10 false 10 5.625,1.104 6.083,1.302 0.458,0.198 10 false SP2+ 5.625,2.229 6.083,2.427 0.458,0.198 10 false SP2-

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (SP2) Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed) -

HINT:
·

SPD (SP2) is always 0 while driving:

Open or short in the sensor or circuit.

·

The SPD (SP2) value displayed on the tester is much lower than the actual vehicle speed:

Sensor trouble, improper installation or intermittent connection trouble in the circuit.





PROCEDURE

1.INSPECT SPEED SENSOR SP2 INSTALLATION
a.
C211922E01
0.838,0.127 1.078,0.329 0.240,0.202 10 *a 2.303,0.127 2.543,0.329 0.240,0.202 10 *b

Check the speed sensor SP2 installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.


Text in Illustration
*a CORRECT
*b INCORRECT



OK

2.INSPECT SPEED SENSOR SP2

NG

SECURELY INSTALL OR REPLACE SPEED SENSOR SP2

2.INSPECT SPEED SENSOR SP2
a.
C206284E06
0.056,0.003 0.296,0.205 0.240,0.202 10 *a 1.303,1.682 1.603,1.103 false 1.196,1.707 1.643,1.909 0.446,0.202 10 2 2.15,1.682 1.852,1.103 false 2.152,1.707 2.598,1.909 0.446,0.202 10 1

Disconnect the B33 speed sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω


Text in Illustration
*a Component without harness connected
(Speed Sensor SP2)



OK

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - ECM)
a.
U180914E02
1.979,2.771 2.25,1.958 false 2.563,2.76 2.292,1.958 false 0.052,0.031 0.302,0.229 0.25,0.198 10 false *a 2.25,0.406 2.625,0.635 0.375,0.229 10 false B38 1.51,2.802 2.146,3 0.635,0.198 10 false 10 (SP2-) 2.417,2.802 3.052,3 0.635,0.198 10 false 9 (SP2+)

Disconnect the B38 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B38-9 (SP2+) - B38-10 (SP2-) 20°C (68°F) 560 to 680 Ω
B38-9 (SP2+) - Body ground Always 10 kΩ or higher
B38-10 (SP2-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR