Home › Drivetrain › A750E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1440E _52 Drivetrain _056133 A750E AUTOMATIC TRANSMISSION / TRANSAXLE _0273938 AUTOMATIC TRANSMISSION SYSTEM C

A750E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0973  Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1)  P0974  Shift Solenoid "A" Control Circuit High (Shift Solenoid Valve S1)  


DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2 and SR, which is controlled by the ECM. If an open or short circuit occurs in one of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly. In case of an open or short circuit, the ECM stops sending current to the circuit. For details, refer to the fail-safe chart (See page Drivetrain>A750E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).

DTC Code DTC Detection Condition Trouble Area
P0973 The ECM detects a short in the solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1-trip detection logic).
·

Short in shift solenoid valve S1 circuit

·

Shift solenoid valve S1

·

ECM


P0974 The ECM detects an open in the solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1-trip detection logic).
·

Open in shift solenoid valve S1 circuit

·

Shift solenoid valve S1

·

ECM



MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S1 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When the shift solenoid valve S1 is on, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift solenoid valve S1 circuit.

When the shift solenoid valve S1 is off, if its resistance is 100 kΩ or higher, the ECM determines there is an open in the shift solenoid valve S1 circuit (See page Drivetrain>A750E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).

WIRING DIAGRAM

C361838E01
1,2.75 1.458,2.948 0.458,0.198 10 false B32 1,2.917 2.75,3.333 1.75,0.417 10 false Transmission Wire 1,1.729 2.719,2.104 1.719,0.375 10 false Shift Solenoid Valve S1 5.917,3.083 6.375,3.281 0.458,0.198 10 false B37 5.917,3.25 6.375,3.448 0.458,0.198 10 false ECM 5.74,1 6.198,1.198 0.458,0.198 10 false S1 5.438,1.135 5.75,1.333 0.313,0.198 10 false 36 2.771,1.135 3.083,1.333 0.313,0.198 10 false 8 2.427,0.875 2.719,1.083 0.292,0.208 10 false S1

CAUTION / NOTICE / HINT

HINT:

The shift solenoid valve S1 turns ON/OFF normally when the shift lever is in D.

ECM gear shift command 1st 2nd 3rd 4th 5th
Shift solenoid valve S1 ON ON OFF OFF OFF


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S1)
a.
C214326E04
1.221,1.087 0.967,1.745 false 0.055,0.021 0.279,0.187 0.224,0.167 10 *a 0.84,1.783 1.076,1.950 0.236,0.167 10 S1

Disconnect the B32 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (S1) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE S1
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
U180910E02
1.594,2.771 1.854,2.219 false 0.052,0.042 0.302,0.24 0.25,0.198 10 false *a 1.854,0.396 2.229,0.625 0.375,0.229 10 false B37 1.323,2.802 1.833,3 0.51,0.198 10 false 36 (S1)

Disconnect the B37 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-36 (S1) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR