Home › Drivetrain › A750E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1440E _52 Drivetrain _056133 A750E AUTOMATIC TRANSMISSION / TRANSAXLE _0273938 AUTOMATIC TRANSMISSION SYSTEM C

A750E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2759  Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)  


DESCRIPTION

The amount of current flow to the solenoid is controlled by the duty ratio* of the ECM output signal. During the lock-up operation, if the duty ratio increases, the lock-up hydraulic pressure increases.

C159072E11
4.76,2.823 5.073,1.917 5.073,1.917 5.146,1.917 false 4.979,2.979 5.125,3.385 5.125,3.385 5.188,3.385 false 5.729,3.073 5.844,3.385 5.844,3.385 5.906,3.385 false 5.958,3.302 6.844,3.521 0.885,0.219 10 false Solenoid Coil 0.042,0.563 1.292,0.781 1.25,0.219 10 false Hydraulic Pressure 2.521,2.948 3.083,3.167 0.563,0.219 10 false Current 5.156,1.302 5.74,1.521 0.583,0.219 10 false 1 Cycle 5.448,0.729 5.625,0.948 0.177,0.219 10 false B 5.031,0.177 5.208,0.396 0.177,0.219 10 false A 5.24,3.302 5.771,3.521 0.531,0.219 10 false Sleeve 5.198,1.833 6.031,2.052 0.833,0.219 10 false Spool Valve

HINT:

*: The duty ratio is the ratio of the current ON time (A) to the total of the current ON and OFF time (A + B). Duty Ratio (%) = A / (A + B) x 100


DTC Code DTC Detection Condition Trouble Area
P2759 Open or short is detected in the shift solenoid valve SLU circuit for 1 sec. or more while driving (1-trip detection logic).
·

Open or short in shift solenoid valve SLU circuit

·

Shift solenoid valve SLU

·

ECM



MONITOR DESCRIPTION

When an open or short in the shift solenoid valve (SLU) circuit is detected, the ECM determines there is a malfunction. The ECM will turn on the MIL and store this DTC.

WIRING DIAGRAM

C361837E03
0.969,3.083 2.5,3.281 1.531,0.198 10 false Transmission Wire 0.958,2.917 1.427,3.125 0.469,0.208 10 false B32 1.01,1.792 2.677,2.031 1.667,0.24 10 false Shift Solenoid Valve SLU 2.771,1.333 3.083,1.531 0.313,0.198 10 false 13 2.771,2.552 3.083,2.75 0.313,0.198 10 false 5 0.792,2.219 1.104,2.417 0.313,0.198 10 false 1 0.792,1.396 1.104,1.594 0.313,0.198 10 false 2 5.438,1.333 5.75,1.531 0.313,0.198 10 false 33 5.438,2.552 5.75,2.75 0.313,0.198 10 false 32 5.75,2.417 6.208,2.615 0.458,0.198 10 false SLU- 5.75,1.219 6.208,1.417 0.458,0.198 10 false SLU+ 5.917,3.24 6.375,3.438 0.458,0.198 10 false B37 5.917,3.385 6.375,3.583 0.458,0.198 10 false ECM 2.271,1.104 2.729,1.302 0.458,0.198 10 false SLU+ 2.26,2.313 2.719,2.51 0.458,0.198 10 false SLU-

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)
a.
C214326E09
1.583,1.306 1.384,1.745 false 1.656,1.087 1.911,1.745 false 1.154,1.783 1.561,1.950 0.407,0.167 10 SLU+ 0.055,0.021 0.279,0.187 0.224,0.167 10 *a 1.746,1.783 2.126,1.950 0.380,0.167 10 SLU-

Disconnect the B32 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SLU+) - 5 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
13 (SLU+) - Body ground Always 10 kΩ or higher
5 (SLU-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLU
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
U180912E02
1.75,2.771 2.021,2.219 false 2.344,2.771 2.073,2.219 false 0.052,0.031 0.302,0.229 0.25,0.198 10 false *a 1.865,0.406 2.24,0.635 0.375,0.229 10 false B37 1.198,2.802 1.875,3 0.677,0.198 10 false 33 (SLU+) 2.146,2.802 2.823,3 0.677,0.198 10 false 32 (SLU-)

Disconnect the B37 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-33 (SLU+) - B37-32 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
B37-33 (SLU+) - Body ground Always 10 kΩ or higher
B37-32 (SLU-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLU
a.
C209928E28
1.76,0.979 2.208,0.396 false 1.51,0.99 1.052,0.406 false 1.76,2.948 2.208,2.354 false 1.51,2.948 1.052,2.354 false 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 2.24,0.26 2.406,0.458 0.167,0.198 10 false 1 0.917,0.271 1.083,0.469 0.167,0.198 10 false 2 2.24,2.188 2.406,2.385 0.167,0.198 10 false 1 0.917,2.188 1.083,2.385 0.167,0.198 10 false 2 1.927,3.927 2.125,4.125 0.198,0.198 10 false (-) 1.115,3.927 1.333,4.125 0.219,0.198 10 false (+)

Remove shift solenoid valve SLU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes operating noise



Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve SLU)


OK

NG