Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1440E _52 Drivetrain _056134 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0273939 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0985  Shift Solenoid "E" Control Circuit Low (Shift Solenoid Valve SR)  P0986  Shift Solenoid "E" Control Circuit High (Shift Solenoid Valve SR)  


DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2 and SR, which is controlled by the ECM. If an open or short circuit occurs in one of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly. In case of an open or short circuit, the ECM stops sending current to the circuit. For details, refer to the fail-safe chart (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).

DTC Code DTC Detection Condition Trouble Area
P0985 The ECM detects a short in the solenoid valve SR circuit 2 times when solenoid valve SR is operated (1-trip detection logic).
·

Short in shift solenoid valve SR circuit

·

Shift solenoid valve SR

·

ECM


P0986 The ECM detects an open in the solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1-trip detection logic).
·

Open in shift solenoid valve SR circuit

·

Shift solenoid valve SR

·

ECM



MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve SR circuit. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When the shift solenoid valve SR is on, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift solenoid valve SR circuit.

When the shift solenoid valve SR is off, if its resistance is 100 kΩ or higher, the ECM determines there is an open in the shift solenoid valve SR circuit (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).

WIRING DIAGRAM

C361838E03
1,2.75 1.458,2.948 0.458,0.198 10 false B32 1,2.917 2.75,3.333 1.75,0.417 10 false Transmission Wire 1,1.729 2.719,2.104 1.719,0.375 10 false Shift Solenoid Valve SR 5.917,3.083 6.375,3.281 0.458,0.198 10 false B36 5.917,3.25 6.375,3.448 0.458,0.198 10 false ECM 5.74,1 6.198,1.198 0.458,0.198 10 false SR 5.438,1.135 5.75,1.333 0.313,0.198 10 false 31 2.771,1.135 3.083,1.333 0.313,0.198 10 false 7 2.427,0.875 2.719,1.083 0.292,0.208 10 false SR

CAUTION / NOTICE / HINT

HINT:

The shift solenoid valve SR turns ON/OFF normally when the shift lever is in D.

ECM gear shift command 1st 2nd 3rd 4th 5th
Shift solenoid valve SR OFF OFF OFF OFF ON


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SR)
a.
C214326E06
1.365,1.087 1.11,1.745 false 0.055,0.021 0.279,0.187 0.224,0.167 10 *a 0.981,1.783 1.236,1.950 0.255,0.167 10 SR

Disconnect the B32 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (SR) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SR
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
U180909E02
2.021,2.76 1.76,2.219 false 0.052,0.031 0.302,0.229 0.25,0.198 10 false *a 1.49,0.396 1.865,0.625 0.375,0.229 10 false B36 1.854,2.802 2.375,3 0.521,0.198 10 false 31 (SR)

Disconnect the B36 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B36-31 (SR) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR