READ DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Neutral Position SW Signal | PNP switch status/
ON or OFF |
·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.
|
| Transfer Neutral | Transfer status/
ON or OFF |
·
ON: Transfer in neutral ·
OFF: Transfer not in neutral |
- |
| Transfer L4 | Transfer status/
ON or OFF |
·
ON: Transfer in L4 ·
OFF: Transfer not in L4 |
- |
| Stop Light Switch | Stop light switch status/
ON or OFF |
·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| SPD (NT) | Input shaft speed/
Min.: 0 rpm Max.: 12750 rpm |
·
Lock-up ON (after warming up engine): Input turbine speed (NT) is equal to engine speed ·
Lock-up OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed |
Data is displayed in increments of 50 rpm. |
| SPD (SP2) | Output shaft speed/
Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) |
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed) | - |
| Shift SW Status (P Range) | PNP switch status/
ON or OFF |
·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.
|
| Shift SW Status (R Range) | PNP switch status/
ON or OFF |
·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.
|
| Shift SW Status (N Range) | PNP switch status/
ON or OFF |
·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.
|
| Shift SW Status (N,P Range) Supported | Status of park/neutral position switch (N or P) supported
Unsupp or Supp |
Supp | - |
| Shift SW Status (N, P Range) | PNP switch status (P or N)/
ON or OFF |
Shift lever in N or P: ON
Shift lever not in N or P: OFF |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Sports Shift Up SW | Sport shift up switch status/
ON or OFF |
·
ON: Shift lever held in "+" (up-shift) ·
OFF: Shift lever not held in "+" (up-shift) |
- |
| Sports Shift Down SW | Sport shift down switch status/
ON or OFF |
·
ON: Shift lever held in "-" (down-shift) ·
OFF: Shift lever not held in "-" (down-shift) |
- |
| Sports Mode Selection SW | Sport mode select switch status/
ON or OFF |
·
ON: Shift lever in S, "+" or "-" ·
OFF: Shift lever not in S, "+" or "-" |
- |
| Shift SW Status (D Range) | PNP switch status/
ON or OFF |
·
ON: Shift lever in D, S, "+" or "-" ·
OFF: Shift lever not in D, S, "+" or "-" |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.
|
| A/T Oil Temperature 1 | No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F) Max.: 215°C (419°F) |
·
After stall test: Approximately 80°C (176°F) ·
With engine cold: Equal to ambient temperature |
If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted. |
| A/T Oil Temperature 2 | No. 2 ATF temperature sensor value/
Min.: -40°C (-40°F) Max.: 215°C (419°F) |
·
After stall test: Approximately 80°C (176°F) ·
With engine cold: Equal to ambient temperature |
If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted. |
| ATF Thermal Degradation Estimate | Estimated value of ATF thermal degradation/
Min.: 0 Max.: 65535 |
- | If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the ATF. |
| Lock Up | Lock-up/
ON or OFF |
·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Shift Status | ECM gear shift command/
1st, 2nd, 3rd, 4th or 5th |
·
1st, 2nd, 3rd, 4th or 5th: Shift lever in D ·
1st, 2nd, 3rd, 4th or 5th: Shift lever in S |
- |
| SLT Solenoid Status | Shift solenoid SLT status/
ON or OFF |
·
OFF: Accelerator pedal depressed ·
ON: Accelerator pedal released |
- |
| SLU Solenoid Status | Shift solenoid SLU status/
ON or OFF |
·
ON: Shift solenoid SLU operating ·
OFF: Shift solenoid SLU not operating |
- |
| Torque Converter Temperature Raise History | Torque converter temperature raise history status/
ON or OFF |
OFF | This item always displays OFF. |
PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the Solenoid (SLU) | Operate shift solenoid SLU | ON or OFF | [Vehicle Condition]
·
Engine stopped. ·
Shift lever in P or N. |
| Activate the Solenoid (SLT)* | Operate shift solenoid SLT and raise line pressure | ON or OFF
|
[Vehicle Condition]
·
Vehicle stopped. ·
Engine idling. |
| Activate the Solenoid (S1) | Operate shift solenoid S1 | ON or OFF | [Vehicle Condition]
·
Engine stopped. ·
Shift lever in P or N. |
| Activate the Solenoid (S2) | Operate shift solenoid S2 | ON or OFF | [Vehicle Condition]
·
Engine stopped. ·
Shift lever in P or N. |
| Activate the Lock Up | Control shift solenoid SLU to set automatic transmission to lock-up | ON or OFF | Possible to check shift solenoid valve SLU operation.
[Vehicle Condition] ·
Throttle valve opening angle: Less than 35%. ·
Vehicle speed: 60 km/h (37 mph) or more. |
| Control the Shift Position | Operate shift solenoid valve and set each shift position | ·
Press "→" button: Shift up ·
Press "←" button: Shift down |
Possible to check operation of the shift solenoid valves.
[Vehicle Condition] 50 km/h (31 mph) or less. |
| Activate the Solenoid (SR) | Operate shift solenoid SR | ON or OFF | [Vehicle Condition]
·
Engine stopped. ·
Shift lever in P or N. |
| Activate the Solenoid (SL1) | Operate shift solenoid SL1 | ON or OFF | [Vehicle Condition]
·
Engine stopped. ·
Shift lever in P or N. |
| Activate the Solenoid (SL2) | Operate shift solenoid SL2 | ON or OFF | [Vehicle Condition]
·
Engine stopped. ·
Shift lever in P or N. |
*: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>HYDRAULIC TEST) as well. Note that the pressure values in the Active Test and Hydraulic Test are different.