Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › SHIFT LEVER
RM1440E _52 Drivetrain _056134 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0273945 SHIFT LEVER A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSTALLATION  


PROCEDURE

Hide 58995A 1.INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET

a.

Install the console box mounting bracket with the 2 screws.


Hide 33530F 2.INSTALL SHIFT LEVER ASSEMBLY

U150241E02
1.396,1.906 1.51,2.063 0.115,0.156 10 false 3 2.406,0.292 2.521,0.448 0.115,0.156 10 false 4 2.302,1.938 2.417,2.094 0.115,0.156 10 false 2 1.375,0.354 1.49,0.51 0.115,0.156 10 false 1

a.

Install the transmission floor shift with the 4 bolts tighten the bolt in the order shown in the illustration.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


b.

Connect the 2 connectors and attach the 4 wire harness clamps.


Hide 33820B 3.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Turn the socket of the transmission control cable 180° counterclockwise. While holding the socket in place, push in the lock piece until the lock piece clicks twice.

NOTICE:

Do not over-rotate the socket as it will come off the internal spring and the transmission control cable will not be reusable.


C216621E02
1.617,1.223 1.617,1.453 1.617,1.453 1.853,1.453 false 1.56,0.543 1.56,0.328 1.56,0.328 1.326,0.328 false 1.875,1.381 2.046,1.536 0.171,0.155 10 *1 1.161,0.252 1.341,0.413 0.180,0.161 10 *2 3.706,0.101 3.887,0.262 0.180,0.161 10 *a

Text in Illustration
*1 Socket *2 Lock Piece
*a Push in - -

HINT:

If the lock piece cannot be pushed in, slightly turn the socket clockwise and then push in the lock piece again.



b.

Install the outer part of the transmission control cable to the shift lever retainer. Check that the socket and lock piece are positioned at original position.

C216998E01
0.747,1.444 0.932,1.612 0.185,0.168 10 *1 1.393,1.264 0.995,1.513 0.995,1.513 0.911,1.513 false

Text in Illustration
*1 Shift Lever Retainer - -


c.
C203381E01
1.358,0.382 1.530,0.547 0.171,0.165 10 *1 1.46,1.83 1.631,1.995 0.171,0.165 10 *1 2.491,1.697 2.700,1.881 0.209,0.184 10 *2 2.538,1.357 2.747,1.541 0.209,0.184 10 *2 1.814,1.007 1.672,0.481 1.672,0.481 1.574,0.481 false 1.846,2.23 1.762,1.92 1.762,1.92 1.665,1.92 false 2.452,2.097 2.368,1.787 2.368,1.787 2.466,1.787 false 2.34,1.133 2.424,1.443 2.424,1.443 2.521,1.443 false

Slide the slider in the direction shown in the illustration and pull out the lock piece.

Text in Illustration
*1 Slider
*2 Lock Piece


d.
C204586

Connect the end of the cable to the shift lever.

NOTICE:
·

Make sure that the lock piece is pulled up.

·

Push on the end of the cable all the way to the base of the pin.




e.
C361848

Push the lock piece into the adjuster case and lock it.

NOTICE:

Make sure that the lock piece is completely locked by the slider.



Hide 58910C 5.INSTALL REAR CONSOLE BOX ASSEMBLY