1.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY
Remove the front differential carrier assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT DIFFERENTIAL CARRIER ASSEMBLY(for 4WD)>REMOVAL).
41204D
2.REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT
Using SST and a hammer, loosen the staked part of the nut.
Using SST to hold the companion flange, remove the nut.
| *a | Turn |
| *b | Hold |
41204D
3.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
Using SST, remove the companion flange.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
4.REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL
Using SST, remove the oil seal.
| *1 | Oil Seal |
| *2 | Oil Slinger |
41214C
5.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
41211B
6.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
Using SST, remove the roller bearing (inner).
Using SST, tap out the roller bearing (outer).
41115F
7.REMOVE FRONT DIFFERENTIAL OIL STORAGE RING
Using a screwdriver and hammer, tap out the oil storage ring.
41231F
8.REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
Remove the bearing spacer.
41231F
9.INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
Install a new bearing spacer.
Install the spacer so that it is facing in the correct direction.
41115F
10.INSTALL FRONT DIFFERENTIAL OIL STORAGE RING
Using a brass bar and hammer, tap in a new oil storage ring.
Be careful not to damage the oil storage ring.
41211B
11.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
Using SST and a hammer, install the roller bearing (outer).
Install the roller bearing (inner).
41214C
12.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
41101D
13.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL
Apply MP grease to the lip of a new oil seal.
Using SST and a hammer, tap in the oil seal.
3.9 to 4.8 mm (0.154 to 0.188 in.)
| *a | Oil Seal Depth |
41204D
14.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
Using SST, install the companion flange.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
Using SST to hold the companion flange, install the nut.
or less
15.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD
Using a torque wrench, measure the preload.
| Item | Specified Condition |
|---|---|
| New bearing | 0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 13.9 in.*lbf) |
| Used bearing | 0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf) |
If the result is not as specified, adjust the preload.
| Item | Specified Condition |
|---|---|
| New bearing | 1.2 to 2.45 N*m (12 to 25 kgf*cm, 10.6 to 21.7 in.*lbf) |
| Used bearing | 0.71 to 1.66 N*m (7.2 to 17 kgf*cm, 6.3 to 14.7 in.*lbf) |
41204E
16.STAKE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT
Using a chisel and hammer, stake the nut.
17.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY
Install the front differential carrier assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT DIFFERENTIAL CARRIER ASSEMBLY(for 4WD)>INSTALLATION).