Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY
RM1440E _52 Drivetrain _056137 AXLE AND DIFFERENTIAL _0273979 REAR DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 1.ASSEMBLE DIFFERENTIAL CASE

C216548

a.

Install the rear differential side gear thrust washer to the rear differential side gear.


b.

Install the rear differential pinion thrust washer and rear differential pinion to the rear differential spider.


c.

Fix the differential case RH in place.


d.
ZK09096

Install the rear differential side gear and rear differential spider to the differential case RH.


e.
ZK09097

Using a dial indicator, measure the differential case RH side backlash while pushing the pinion toward the case.

Standard backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)



f.

Remove the rear differential spider from the differential case RH.


g.
ZK09098

Install the rear differential side gear and rear differential spider to the differential case LH.


h.

Using a dial indicator, measure the differential case LH side backlash while pushing the pinion toward the case.

Standard backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


If the backlash is not within the specification, install 2 side gear thrust washers of a different thickness.

Standard Thrust Washer:
Thickness Thickness
0.87 to 0.93 mm (0.0343 to 0.0366 in.) 1.17 to 1.23 mm (0.0461 to 0.0484 in.)
0.97 to 1.03 mm (0.0382 to 0.0406 in.) 1.27 to 1.33 mm (0.0500 to 0.0524 in.)
1.07 to 1.13 mm (0.0421 to 0.0445 in.) -



i.
C216546E10
0.604,1.594 0.875,1.76 0.875,1.76 0.615,1.854 false 0.917,1.698 1.115,1.875 0.198,0.177 10 true *1

Align the matchmarks and assemble the differential case from the RH and LH cases.

Text in Illustration
*a Matchmark


j.

Using a plastic-faced hammer, install the differential case.


k.

Install the 8 bolts.

Torque:
47 N*m (480 kgf*cm, 35 ft.*lbf)


Hide 2.INSTALL DIFFERENTIAL RING GEAR

a.

Clean the contact surfaces of the differential case and ring gear.


b.

Heat the ring gear in water that is approximately 100°C (212°F).


c.

Carefully remove the ring gear from the boiling water.


d.

After the moisture on the ring gear has completely evaporated, quickly install the ring gear to the differential case.


e.
C216547E17
1.635,1.927 1.458,2.021 1.458,2.021 1.635,1.802 true 1.25,1.969 1.427,2.135 0.177,0.167 10 true *a

Align the matchmarks on the ring gear with that of the differential case.

Text in Illustration
*a Matchmark


f.

After the ring gear cools down sufficiently, apply adhesive to the 12 bolts and install them.

Adhesive:

Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent


Torque:
97 N*m (985 kgf*cm, 71 ft.*lbf)


Hide 41301A 3.INSTALL REAR DIFFERENTIAL CASE BEARING

C216550E01
1.588,0.882 1.206,1.141 false 1.016,1.146 1.315,1.304 0.298,0.158 10 SST 1.904,2.717 2.688,2.424 false 2.698,2.34 2.996,2.498 0.298,0.158 10 SST

a.

Using SST and a press, press the bearing onto the differential case.

SST
09308-14010  
09950-60010  (09951-00490)


Hide 4.INSPECT DIFFERENTIAL RING GEAR RUNOUT

C216538

a.

Install the differential case to the carrier and install the 2 adjusting nuts so that there is no play in the bearing.


b.

Install the 2 bearing caps with the 4 bolts.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)


c.

Using a dial indicator, measure the runout of the ring gear.

Maximum runout:

0.07 mm (0.00276 in.)



d.

Remove the 2 bearing caps, 2 adjusting nuts and differential case.


Hide 41201B 5.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

C197664E01
2.28,0.481 2.577,0.630 0.297,0.149 10 SST 1.953,0.567 2.256,0.567 2.256,0.567 1.97,0.933 false

a.

Using SST and a press, press in the roller bearing (outer) to the carrier.

SST
09308-14010  
09309-14040  


Hide 41201A 6.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C216552E01
1.286,0.861 0.406,0.861 0.406,0.861 1.154,2.119 false 0.054,0.786 0.359,0.944 0.305,0.159 10 SST

Install the plate washer to the carrier.

HINT:

First, install a washer with the same thickness as the removed washer, and then check the tooth contact pattern. Replace the washer with one of a different thickness if necessary.



b.

Using SST and a press, press the roller bearing (outer) into the carrier.

SST
09950-70010  (09951-07200)
09255-10012  


Hide 41201A 7.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

SA03102E18
1.875,1.354 2.563,0.688 false 2.625,0.573 2.948,0.75 0.323,0.177 10 false SST

a.

Using SST and a press, press the roller bearing (inner) onto the drive pinion.

SST
09309-14040  


Hide 8.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

C028218

a.

Install the drive pinion, rear drive pinion tapered roller bearing and rear differential drive pinion oil slinger.

HINT:

Install the spacer and oil seal after adjusting the gear contact pattern.



b.
R011163

Using SST, install the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil LSD to its threads and tip.



c.
C361813E01
0.688,1.094 0.417,0.708 false 0.115,0.604 0.573,0.802 0.458,0.198 10 false SST

Using a 30 mm socket wrench, adjust the drive pinion preload by tightening the companion flange nut.


d.

Using SST to hold the companion flange in place, tighten the nut.

SST
09330-00021  

Torque:
457 N*m (4660 kgf*cm, 337 ft.*lbf)

or less


NOTICE:
·

As there is no spacer, tighten the nut a little at a time. Be careful not to overtighten the nut.


·

Apply hypoid gear oil to the nut.




e.
C003092

Using a torque wrench, measure the preload.

Standard Preload (at Starting):
Item Specified Condition
New bearing 0.83 to 2.18 N*m (8.64 to 22.2 kgf*cm, 7.35 to 19.3 in.*lbf)
Used bearing 0.88 to 1.98 N*m (8.97 to 20.2 kgf*cm, 7.79 to 17.5 in.*lbf)


NOTICE:

For a more accurate measurement, rotate the bearing forward and backward several times before measuring.



Hide 9.INSTALL DIFFERENTIAL CASE ASSEMBLY

C216542

a.

Place the 2 bearing outer races on their respective bearings.

HINT:

Do not interchange the right and left races.



Hide 10.ADJUST RING GEAR BACKLASH

a.
C217048

Install the plate washer on the side without the ring gear teeth.

NOTICE:

Make sure that the ring gear has backlash.



b.
C216537

Using a dial indicator, while holding the companion flange, measure the ring gear backlash.

Standard backlash (reference):

0.10 to 0.20 mm (0.00394 to 0.00787 in.)



c.
C217048

Select a plate washer for the side without the ring gear teeth using the backlash as a reference.


d.
C216549

Select a plate washer for the side with the ring gear teeth so that there is no clearance between the outer race and case.


e.

Using a plastic-faced hammer, install the plate washer for the side with the ring gear teeth.


f.
C216537

Using a dial indicator, while holding the companion flange, measure the ring gear backlash.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

HINT:
·

There should be no clearance between the plate washer and case.

·

Make sure that there is ring gear backlash.




Hide 11.ADJUST SIDE BEARING PRELOAD

C124163

a.

Remove the ring gear teeth side plate washer and, using a micrometer, measure the thickness.


b.

Using the backlash as a reference, select a new washer that is 0.05 to 0.20 mm (0.00197 to 0.00787 in.) thicker than the removed washer and, using a plastic-faced hammer, tap it in so that it fits against the bearing.

HINT:

Select a washer which can be pressed in 2/3 of the full amount with your finger.



c.
C216537

Recheck the ring gear backlash.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00788 in.)


If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

HINT:

An approximately 0.02 mm (0.000787 in.) change in each plate washer results in a 0.03 mm (0.00118 in.) change in the backlash.


Standard Washer:
Mark Thickness Mark Thickness
70 2.05 to 2.07 mm (0.0808 to 0.0816 in.) 62 2.41 to 2.43 mm (0.0950 to 0.0957 in.)
71 2.07 to 2.09 mm (0.0816 to 0.0823 in.) 63 2.43 to 2.45 mm (0.0957 to 0.0965 in.)
72 2.09 to 2.11 mm (0.0823 to 0.0831 in.) 64 2.45 to 2.47 mm (0.0965 to 0.0973 in.)
73 2.11 to 2.13 mm (0.0831 to 0.0839 in.) 65 2.47 to 2.49 mm (0.0972 to 0.0980 in.)
74 2.13 to 2.15 mm (0.0839 to 0.0847 in.) 66 2.49 to 2.51 mm (0.0980 to 0.0988 in.)
75 2.15 to 2.17 mm (0.0847 to 0.0855 in.) 67 2.51 to 2.53 mm (0.0988 to 0.0996 in.)
76 2.17 to 2.19 mm (0.0855 to 0.0863 in.) 68 2.53 to 2.55 mm (0.0996 to 0.1000 in.)
77 2.19 to 2.21 mm (0.0863 to 0.0871 in.) 69 2.55 to 2.57 mm (0.1000 to 0.1012 in.)
78 2.21 to 2.23 mm (0.0871 to 0.0879 in.) 01 2.57 to 2.59 mm (0.1012 to 0.1020 in.)
79 2.23 to 2.25 mm (0.0879 to 0.0887 in.) 32 2.59 to 2.61 mm (0.1020 to 0.1028 in.)
80 2.25 to 2.27 mm (0.0887 to 0.0894 in.) 33 2.61 to 2.63 mm (0.1028 to 0.1035 in.)
81 2.27 to 2.29 mm (0.0894 to 0.0902 in.) 03 2.63 to 2.65 mm (0.1035 to 0.1043 in.)
82 2.27 to 2.31 mm (0.0902 to 0.0891 in.) 34 2.65 to 2.67 mm (0.1043 to 0.1051 in.)
83 2.31 to 2.33 mm (0.0910 to 0.0918 in.) 35 2.67 to 2.69 mm (0.1051 to 0.1059 in.)
84 2.33 to 2.35 mm (0.0918 to 0.0926 in.) 05 2.69 to 2.71 mm (0.1059 to 0.1067 in.)
85 2.35 to 2.37 mm (0.0926 to 0.0934 in.) 36 2.71 to 2.73 mm (0.1067 to 0.1075 in.)
86 2.37 to 2.39 mm (0.0934 to 0.0942 in.) 37 2.73 to 2.75 mm (0.1075 to 0.1082 in.)
87 2.39 to 2.41 mm (0.0942 to 0.0950 in.) 07 2.75 to 2.77 mm (0.1082 to 0.1091 in.)



Hide 12.INSTALL BEARING CAP

a.
C216540E02
2.065,2.589 1.529,3.125 1.529,3.125 2.063,2.697 false 1.425,3.136 1.577,3.283 0.151,0.147 10 *1

Align the matchmarks on the cap and carrier.

Text in Illustration
*a Matchmark


b.

Install the 2 bearing caps with the 4 bolts.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

HINT:

After rotating the ring gear 5 times or more, recheck the backlash.



Hide 13.INSPECT DIFFERENTIAL RING GEAR RUNOUT

a.
C216538

Using a dial indicator, measure the runout of the ring gear.

Maximum runout:

0.07 mm (0.00276 in.)


If the runout is more than the maximum, replace the ring gear.


Hide 14.INSPECT TOTAL PRELOAD

C003092

a.

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard total preload (at starting):

Drive pinion preload plus 0.20 to 0.40 N*m (2.0 to 4.1 kgf*cm, 1.8 to 3.5 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 15.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

C217045

a.

Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.


b.

Hold the companion flange firmly in place and rotate the ring gear in both directions.


c.

Inspect the tooth contact pattern.

C113184E01
1.159,1.073 2.171,1.257 1.012,0.184 10 Proper Contact 2.393,0.145 3.095,0.311 0.702,0.165 10 Drive Side 3.664,0.166 4.459,0.350 0.795,0.184 10 Toe Contact 5.513,0.182 6.372,0.347 0.860,0.165 10 Face Contact 3.454,1.608 6.274,1.949 2.820,0.341 10 Select an adjusting washer that will shift the drive pinion closer to the ring gear. 3.568,2.548 4.419,2.713 0.850,0.165 10 Heel Contact 5.391,2.527 6.330,2.707 0.939,0.180 10 Flank Contact 3.552,3.988 6.328,4.376 2.776,0.387 10 Select an adjusting washer that will shift the drive pinion away from the ring gear. 2.377,4.981 3.089,5.164 0.711,0.184 10 Coast Side 3.562,5.022 4.413,5.187 0.850,0.165 10 Heel Contact 5.385,5.001 6.324,5.181 0.939,0.180 10 Flank Contact 3.594,7.419 4.389,7.602 0.795,0.184 10 Toe Contact 5.442,7.435 6.302,7.600 0.860,0.165 10 Face Contact 3.384,6.445 6.169,6.814 2.786,0.369 10 Select an adjusting washer that will shift the drive pinion closer to the ring gear. 3.547,8.831 6.288,9.181 2.740,0.349 10 Select an adjusting washer that will shift the drive pinion away from the ring gear.

C217047E01
0.813,1.522 1.189,1.827 false 1.12,1.839 1.304,1.981 0.184,0.142 10 *1 0.813,1.522 1.189,1.827 false 1.12,1.839 1.304,1.981 0.184,0.142 10 *1 1.558,1.31 1.934,1.616 false 1.865,1.627 2.049,1.769 0.184,0.142 10 *2

If the teeth are not engaged properly, use the following chart to select a proper washer.

Text in Illustration
*1 Plate Washer
*2 Rear Drive Pinion Rear Tapered Roller Bearing (Outer)

Standard Plate Washer:
Thickness Thickness
1.845 to 1.855 mm (0.0726 to 0.0730 in.) 2.085 to 2.095 mm (0.0821 to 0.0825 in.)
1.855 to 1.865 mm (0.0730 to 0.0734 in.) 2.095 to 2.105 mm (0.0825 to 0.0829 in.)
1.865 to 1.875 mm (0.0734 to 0.0738 in. ) 2.105 to 2.115 mm (0.0829 to 0.0833 in.)
1.875 to 1.885 mm (0.0738 to 0.0742 in.) 2.115 to 2.125 mm (0.0833 to 0.0837 in.)
1.885 to 1.895 mm (0.0742 to 0.0746 in.) 2.125 to 2.135 mm (0.0837 to 0.0841 in.)
1.895 to 1.905 mm (0.0746 to 0.0750 in.) 2.135 to 2.145 mm (0.0841 to 0.0844 in.)
1.905 to 1.915 mm (0.0750 to 0.0754 in.) 2.145 to 2.155 mm (0.0844 to 0.0848 in.)
1.915 to 1.925 mm (0.0754 to 0.0758 in.) 2.155 to 2.165 mm (0.0848 to 0.0852 in.)
1.925 to 1.935 mm (0.0758 to 0.0762 in.) 2.165 to 2.175 mm (0.0852 to 0.0856 in.)
1.935 to 1.945 mm (0.0762 to 0.0766 in.) 2.175 to 2.185 mm (0.0856 to 0.0860 in.)
1.945 to 1.955 mm (0.0766 to 0.0770 in.) 2.185 to 2.195 mm (0.0860 to 0.0864 in.)
1.955 to 1.965 mm (0.0770 to 0.0774 in.) 2.195 to 2.205 mm (0.0864 to 0.0868 in.)
1.965 to 1.975 mm (0.0774 to 0.0778 in.) 2.205 to 2.215 mm (0.0868 to 0.0872 in.)
1.975 to 1.985 mm (0.0778 to 0.0781 in.) 2.215 to 2.225 mm (0.0872 to 0.0876 in.)
1.985 to 1.995 mm (0.0781 to 0.0785 in.) 2.225 to 2.235 mm (0.0876 to 0.0880 in.)
1.995 to 2.005 mm (0.0785 to 0.0789 in.) 2.235 to 2.245 mm (0.0880 to 0.0884 in.)
2.005 to 2.015 mm (0.0789 to 0.0793 in.) 2.245 to 2.255 mm (0.0884 to 0.0888 in.)
2.015 to 2.025 mm (0.0793 to 0.0797 in.) 2.255 to 2.265 mm (0.0888 to 0.0892 in.)
2.025 to 2.035 mm (0.0797 to 0.0801 in.) 2.265 to 2.275 mm (0.0892 to 0.0896 in.)
2.035 to 2.045 mm (0.0801 to 0.0805 in.) 2.275 to 2.285 mm (0.0896 to 0.0900 in.)
2.045 to 2.055 mm (0.0805 to 0.0809 in.) 2.285 to 2.295 mm (0.0900 to 0.0904 in.)
2.055 to 5.065 mm (0.0809 to 0.0813 in.) 2.295 to 2.305 mm (0.0904 to 0.0907 in.)
2.065 to 2.075 mm (0.0813 to 0.0817 in.) 2.305 to 2.315 mm (0.0907 to 0.0911 in.)
2.075 to 2.085 mm (0.0817 to 0.0821 in.) -




Hide 41204B 16.REMOVE REAR DRIVE PINION NUT

SA02349E24
2.875,0.51 2.271,0.51 false 2.938,0.427 3.302,0.625 0.365,0.198 10 false SST

a.

Using SST to hold the companion flange in place, remove the nut.

SST
09330-00021  


Hide 41204 17.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 41214 18.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 19.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER)

Hide 41201B 20.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER)

Hide 41231 21.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

C093601

a.

Install a new bearing spacer to the drive pinion.


Hide 41115 22.INSTALL DIFFERENTIAL OIL STORAGE RING

a.
C216551E01
0.876,1.686 1.187,1.841 0.312,0.154 10 SST 1.417,1.784 1.236,1.784 false

Using SST, tap in a new oil storage ring.

SST
09308-14010  


Hide 41201B 23.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER)

Hide 41201B 24.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER)

Hide 41214 25.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201C 26.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

C217046E01
0.937,0.364 1.315,0.534 0.378,0.170 10 SST 1.767,0.455 1.315,0.455 false

a.

Apply MP grease to a new oil seal.


b.

Using SST and a hammer, tap in the oil seal.

SST
09554-30011  

Standard oil seal depth:

-0.3 to 0.3 mm (-0.0118 to 0.0118 in.)



Hide 41204 27.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

R011163E33
1.354,1.469 1.167,1.708 false 0.229,1.25 0.417,1.448 0.188,0.198 10 false *b 1.021,1.74 1.365,1.938 0.344,0.198 10 false SST 2.802,0.292 2.99,0.49 0.188,0.198 10 false *a

a.

Using SST, install the companion flange to the drive pinion.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

Text in Illustration
*a Turn
*b Hold

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



b.
C361798E01
0.833,0.729 0.521,0.406 false 0.219,0.313 0.677,0.51 0.458,0.198 10 false SST

Coat the threads of a new nut with hypoid gear oil.


c.

Using SST to hold the flange, tighten the nut.

SST
09330-00021  

Torque:
457 N*m (4660 kgf*cm, 337 ft.*lbf)

or less



Hide 28.INSPECT DRIVE PINION PRELOAD

SA02352

a.

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard Preload (at Starting):
Item Specified Condition
New bearing 0.83 to 2.18 N*m (8.64 to 22.2 kgf*cm, 7.35 to 19.3 in.*lbf)
Used bearing 0.88 to 1.98 N*m (8.97 to 20.2 kgf*cm, 7.79 to 17.5 in.*lbf)


If the result not as specified, replace the bearing spacer.


If the preload is less than the minimum, retighten the nut with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.


Torque:
457 N*m (4660 kgf*cm, 337 ft.*lbf)

or less


If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repeat the preload adjusting procedure.


HINT:

Do not loosen the pinion nut to reduce the preload.



Hide 29.INSPECT TOTAL PRELOAD

a.
C003092

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard total preload (at starting):

Drive pinion preload plus 0.20 to 0.40 N*m (2.0 to 4.1 kgf*cm, 1.8 to 3.5 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 30.INSPECT DIFFERENTIAL RING GEAR BACKLASH

C216537

a.

Using a dial indicator, check the backlash of the ring gear.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.




Hide 41204 31.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

F001237E50
0.135,0.146 0.365,0.396 0.229,0.25 10 false *a 2.115,0.167 2.344,0.375 0.229,0.208 10 false *b 1.979,1.844 2.417,2.031 0.438,0.188 10 true 30 mm

a.

Using a dial indicator, measure the runout of the drive pinion companion flange vertically and laterally.

Distance from center to runout measurement point:

30 mm (1.18 in.)


Maximum Runout:
Item Specified Condition
Vertical runout 0.14 mm (0.00551 in.)
Lateral runout 0.14 mm (0.00551 in.)


Text in Illustration
*a Vertical Runout
*b Lateral Runout

If the runout is more than the maximum, replace the companion flange.



Hide 41204B 32.STAKE DRIVE PINION NUT

ZK07449

a.

Using a chisel and hammer, stake the nut.