Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL
RM1440E _52 Drivetrain _056137 AXLE AND DIFFERENTIAL _0273978 REAR DIFFERENTIAL CARRIER OIL SEAL A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 37110 1.REMOVE REAR PROPELLER SHAFT ASSEMBLY

a.

for 2WD:

Remove the rear propeller shaft assembly (See page Drivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 2WD)>REMOVAL).


b.

for 4WD:

Remove the rear propeller shaft assembly (See page Drivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 4WD)>REMOVAL).


Hide 41204B 2.REMOVE REAR DRIVE PINION NUT

C089309E21
1.313,0.49 1.313,0.323 false 1.177,0.094 1.552,0.333 0.375,0.24 10 false SST

a.

Using SST and a hammer, loosen the staked part of the rear drive pinion nut.

SST
09930-00010  


b.
B087842E21
2.844,0.729 2.323,0.729 false 2.896,0.667 3.281,0.969 0.385,0.302 10 false SST

Use SST to hold the companion flange.

SST
09330-00021  (09330-00030)


c.

Using a 30 mm socket wrench, remove the rear drive pinion nut.


Hide 41204 3.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

F040720E10
2.021,1.51 2.021,1.708 false 1.896,1.729 2.219,1.885 0.323,0.156 10 false SST

a.

Using SST, remove the rear drive pinion companion flange sub-assembly.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 41201C 4.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

F040717E15
2.5,1.521 2.5,1.802 false 0.99,1.479 0.99,1.75 false 0.99,1.75 1.042,1.75 false 1.188,0.854 1.333,0.396 false 1.333,0.396 1.594,0.396 false 2.375,1.813 2.781,2.021 0.406,0.208 10 false SST 1.083,1.677 1.771,1.854 0.688,0.177 10 false *2 1.635,0.313 2.156,0.49 0.521,0.177 10 false *1

a.

Using SST, remove the rear differential carrier oil seal.

SST
09308-10010  

Text in Illustration
*1 Oil Seal
*2 Oil Slinger


Hide 41214 5.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C216536

Remove the rear differential drive pinion oil slinger.


Hide 41201B 6.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C361749E02
2.583,0.563 2.583,0.167 2.583,0.167 2.771,0.167 false 2.833,0.083 3.292,0.281 0.458,0.198 10 false SST

Using SST, remove the rear drive pinion tapered roller bearing (inner).

SST
09556-22010  


b.
C216535E01
2.574,0.469 2.964,0.672 0.390,0.203 10 SST 2.342,0.552 2.555,0.552 false

Using SST, tap out the rear drive pinion tapered roller bearing (outer).

SST
09308-55010  


Hide 41115 7.REMOVE DIFFERENTIAL OIL STORAGE RING

C217051

a.

Using a screwdriver and hammer, tap out the differential oil storage ring.


Hide 41231 8.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 41231 9.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

C093595

a.

Install a new rear differential drive pinion bearing spacer.

NOTICE:

Install the spacer so that it is facing in the correct direction.



Hide 41115 10.INSTALL DIFFERENTIAL OIL STORAGE RING

C216531E01
1.439,1.637 1.753,1.784 0.313,0.147 10 SST 1.656,1.483 1.609,1.65 false

a.

Using SST and a hammer, tap in a new differential oil storage ring.

SST
09308-14010  

NOTICE:

Be careful not to damage the oil storage ring.



Hide 41201B 11.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

C216532E01
1.22,1.688 1.534,1.845 0.314,0.158 10 SST 0.716,1.486 1.19,1.743 1.19,1.743 1.013,1.44 false

a.

Using SST and a hammer, tap in the rear drive pinion front roller bearing (outer).

SST
09308-14010  


b.

Install the rear drive pinion front roller bearing (inner).


Hide 41214C 12.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

C216536

a.

Install the rear differential drive pinion oil slinger.


Hide 41201C 13.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

C216533E02
1.352,0.24 1.559,0.380 0.207,0.140 10 *a 1.49,1.927 1.801,2.086 0.311,0.158 10 SST 1.716,1.717 1.659,1.927 false

a.

Apply MP grease to the lip of a new oil seal.


b.

Using SST and a hammer, tap in the rear differential carrier oil seal.

SST
09214-76011  

Standard oil seal depth:

-0.30 to 0.30 mm (-0.0118 to 0.0118 in.)


Text in Illustration
*1 Oil Seal Depth


Hide 41204 14.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
F040716E08
2.063,1.5 2.063,1.698 false 1.938,1.719 2.25,1.906 0.313,0.188 10 false SST

Using SST, install the rear drive pinion companion flange sub-assembly.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



b.
B087843E10
0.563,1 1.104,1 false 0.24,0.927 0.615,1.135 0.375,0.208 10 false SST

Using SST to hold the companion flange in place, install the rear drive pinion nut.

SST
09330-00021  (09330-00030)

Torque:
457 N*m (4660 kgf*cm, 337 ft.*lbf)


Hide 15.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

C089308

a.

Using a torque wrench, measure the preload.

Standard Preload (at Starting):
Item Specified Condition
New bearing 0.83 to 2.18 N*m (8.64 to 22.2 kgf*cm, 7.35 to 19.3 in.*lbf)
Used bearing 0.88 to 1.98 N*m (8.97 to 20.2 kgf*cm, 7.79 to 17.5 in.*lbf)


If the result is not as specified, adjust the preload.

Total preload (at starting):

1.08 to 2.38 N*m (11.0 to 24.3 kgf*cm, 9.6 to 21.0 in.*lbf)



Hide 41204B 16.STAKE REAR DRIVE PINION NUT

C089310

a.

Using a chisel and hammer, stake the rear drive pinion nut.


Hide 37110 17.INSTALL REAR PROPELLER SHAFT ASSEMBLY

a.

for 2WD:

Install the rear propeller shaft assembly (See page Drivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 2WD)>INSTALLATION).


b.

for 4WD:

Install the rear propeller shaft assembly (See page Drivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 4WD)>INSTALLATION).


Hide 19.CHECK FOR DIFFERENTIAL OIL LEAKAGE