Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2013.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


U180925E02
0.208,0.083 0.458,0.302 0.25,0.219 10 false *a 2.656,0.094 2.979,0.323 0.323,0.229 10 false A6 5.677,0.094 6,0.323 0.323,0.229 10 false A7

Text in Illustration
*a Component without harness connected
(Master Cylinder Solenoid (Skid Control ECU))
- -

Terminal No. (Symbol) Terminal Description
A6-1 (GND1) Master Cylinder Solenoid (Skid Control ECU) ground
A6-2 (+BM1) Power supply for motor
A6-3 (FR+) Front speed sensor RH power supply output
A6-4 (FL-) Front speed sensor LH input
A6-5 (RR+) Rear speed sensor RH power supply output
A6-6 (RL-) Rear speed sensor LH input
A6-7 (STP) Stop light switch assembly
A6-9 (CSW) VSC OFF switch
A6-11 (CANH) CAN communication terminal H
A6-12 (SP1) Speedometer signal
A6-13 (ATRC)* A-TRAC switch
A6-16 (STPO) Stop light switch assembly
A6-17 (FR-) Front speed sensor RH input
A6-18 (FL+) Front speed sensor LH power supply output
A6-19 (RR-) Rear speed sensor RH input
A6-20 (RL+) Rear speed sensor LH power supply output
A6-24 (TS) Sensor test terminal (Signal check switch)
A6-25 (CANL) CAN communication terminal L
A6-27 (EXI)* Center differential lock detection switch
A6-31 (+BS) Power supply for solenoid
A6-32 (GND2) Master Cylinder Solenoid (Skid Control ECU) ground
A6-40 (EXI3) 2WD: IG power supply
4WD: Four wheel drive control ECU
A6-41 (LBL) Brake fluid level warning switch
A6-44 (HDCS)* Downhill assist control switch
A6-45 (STP2) Stop light switch assembly
A6-46 (IG1) IG1 power supply
A7-1 (IG2) IG2 power supply
A7-2 (+BM2) Power supply for motor
A7-4 (GND3) Master Cylinder Solenoid (Skid Control ECU) ground

*: for 4WD



TERMINAL INSPECTION


a.

Disconnect the 2 Master Cylinder Solenoid (Skid Control ECU) connectors and measure the voltage or resistance on the wire harness side.

HINT:

The voltage cannot be measured with the connector connected to the Master Cylinder Solenoid (Skid Control ECU) as the connector is watertight.


U180811E02
0.271,0.135 0.542,0.333 0.271,0.198 10 false *a 2.083,0.885 2.458,1.177 0.375,0.292 10 false A6 5.51,0.885 5.885,1.177 0.375,0.292 10 false A7

Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid (Skid Control ECU))
- -

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A6-2 (+BM1) - Body ground B Power supply for motor
(from battery)
Always 11 to 14 V
A6-7 (STP) - Body ground L Stop light switch assembly Brake pedal depressed → released 8 to 14 V → Below 1.5 V
A6-9 (CSW) - Body ground V-W VSC OFF switch input VSC OFF switch off → on and held 10 kΩ or higher → Below 1 Ω
A6-13 (ATRC) - Body ground* LG A-TRAC switch input A-TRAC switch off → on and held 10 kΩ or higher → Below 1 Ω
A6-16 (STPO) - Body ground LG-B Stop light switch assembly Ignition switch off → ON Below 1.1 V → 11 to 14 V
A6-31 (+BS) - Body ground L-R Power supply for solenoid
(from battery)
Always 11 to 14 V
A6-41 (LBL) - Body ground V-G Brake fluid level warning switch Brake fluid level +/-5 mm (+/-0.196 in.) from minimum level → maximum level Below 1 Ω → 1.9 to 2.1 kΩ
A6-44 (HDCS) - Body ground* P Downhill assist control switch input Downhill assist control switch off → on 10 kΩ or higher → Below 1 Ω
A6-45 (STP2) - Body ground V-G Stop light switch assembly Brake pedal depressed → released 8 to 14 V → Below 1.5 V
A6-46 (IG1) - Body ground G IG1 power supply Ignition switch off → ON Below 1 V → 11 to 14 V
A7-1 (IG2) - Body ground W IG2 power supply Ignition switch off → ON Below 1 V → 11 to 14 V
A7-2 (+BM2) - Body ground B Power supply for motor
(from battery)
Always 11 to 14 V
A6-1 (GND1) - Body ground W-B Ground Always Below 1 Ω
A6-32 (GND2) - Body ground W-B Ground Always Below 1 Ω
A7-4 (GND3) - Body ground W-B Ground Always Below 1 Ω

*: for 4WD