Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  CALIBRATION  


DESCRIPTION


a.

After replacing VSC-related components, clearing and reading the sensor calibration data is necessary.


b.

Follow the chart to perform calibration.

Replacing Parts/Operating Necessary Operation
Master Cylinder Solenoid (Skid Control ECU)
1.

Clearing zero point calibration data

2.

Yaw rate and acceleration sensor zero point calibration

3.

Steering angle sensor zero point calibration

4.

Downhill assist control calibration (for 4WD)


Yaw Rate and Acceleration Sensor
1.

Clearing zero point calibration data

2.

Yaw rate and acceleration sensor zero point calibration

3.

Steering angle sensor zero point calibration


Spiral Cable Sub-assembly (Steering Angle Sensor)
1.

Clearing zero point calibration data

2.

Yaw rate and acceleration sensor zero point calibration

3.

Steering angle sensor zero point calibration





PERFORM YAW RATE AND ACCELERATION SENSOR AND STEERING ANGLE SENSOR ZERO POINT CALIBRATION (When Using Intelligent Tester)


NOTICE:
·

While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).

·

Be sure to perform this procedure on a level surface (with an inclination of less than 1%).



a.

Clear the zero point calibration data.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is centered.


iii.

Check that the shift lever is in P.


iv.

Connect the intelligent tester to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the intelligent tester on.


vii.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Reset Memory.


viii.

Select the skid control ECU to clear the zero point calibration data using the intelligent tester.


ix.

Turn the ignition switch off.



b.

Perform zero point calibration of the yaw rate and acceleration sensor.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is centered.


iii.

Check that the shift lever is in P.

NOTICE:
·

DTCs C1210 (Zero Point Calibration of Yaw Rate Sensor Undone) and C1336 (Zero Point Calibration of Acceleration Sensor Undone) are stored if the shift lever is not in P.

·

If a DTC is output that indicates zero point calibration is incomplete, repeat the procedure starting at the step for clearing the zero point calibration data and system information.




iv.

Connect the intelligent tester to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the intelligent tester on.


vii.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Test Mode.


viii.

Keep the vehicle stationary on a level surface for 5 seconds or more.


ix.

Check that the slip indicator lights come on for several seconds and then blink in test mode pattern (0.125 seconds on and 0.125 seconds off).

HINT:
·

If the slip indicator lights do not blink, perform zero point calibration again.

·

The zero point calibration is performed only once after the system enters test mode.

·

Calibration cannot be performed again until the stored data is cleared.




x.

Turn the ignition switch off and disconnect the intelligent tester.


xi.

Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds.




PERFORM YAW RATE AND ACCELERATION SENSOR AND STEERING ANGLE SENSOR ZERO POINT CALIBRATION (When Using SST Check Wire)


NOTICE:
·

While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).

·

Be sure to perform this procedure on a level surface (with an inclination of less than 1%).



a.

Clear the zero point calibration data.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is centered.


iii.

Check that the shift lever is in P.


iv.

Turn the ignition switch to ON.


v.

The ABS warning light and slip indicator light come on for 3 seconds to indicate that the initial check is completed.


vi.
U115767E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 0.933,1.943 1.238,2.094 0.304,0.151 10 TS

Using SST, connect and disconnect terminals 12 (TS) and 4 (CG) of the DLC3 4 times or more within 8 seconds.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


vii.

Check that the slip indicator light comes on.



b.

Perform zero point calibration of the yaw rate and acceleration sensor.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is centered.


iii.

Check that the shift lever is in P.

NOTICE:
·

DTCs 36 (Zero Point Calibration of Yaw Rate Sensor Undone) and 39 (Zero Point Calibration of Acceleration Sensor Undone) are stored if the shift lever is not in P.

·

If a DTC is output that indicates zero point calibration is incomplete, repeat the procedure starting at the step for clearing the zero point calibration data and system information.




iv.
U115767E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 0.933,1.943 1.238,2.094 0.304,0.151 10 TS

Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


v.

Turn the ignition switch to ON.


vi.

Keep the vehicle stationary on a level surface for 5 seconds or more.


vii.

Check that the slip indicator lights come on for several seconds and then blink in test mode pattern (0.125 seconds on and 0.125 seconds off).

HINT:
·

If the slip indicator light does not blink, perform zero point calibration again.

·

The zero point calibration is performed only once after the system enters test mode.

·

Calibration cannot be performed again until the stored data is cleared.




viii.

Turn the ignition switch off and disconnect SST from the DLC3.


ix.

Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds.




PERFORM DOWNHILL ASSIST CONTROL CALIBRATION (for 4WD)


a.

Enter test mode (when using the intelligent tester).

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the intelligent tester on.


v.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Test Mode.



b.

Enter test mode (when using SST check wire).

i.

Turn the ignition switch off.


ii.
U115767E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 0.933,1.943 1.238,2.094 0.304,0.151 10 TS

Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


iii.

Turn the ignition switch to ON.



c.

Turn the downhill assist control switch off.


d.

Push the downhill assist control switch and check that the downhill assist control indicator light is blinking.


e.

Turn the downhill assist control switch off.


f.

Turn the ignition switch off.


g.

Check if DTC C120A is output.

HINT:

If DTC C120A is not output, calibration was performed successfully.