Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2009.08–2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1403  Rear Speed Sensor RH Malfunction  C1273  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1404  Rear Speed Sensor LH Malfunction  


DESCRIPTION

Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271).

DTC Code DTC Detection Condition Trouble Area
C1403
C1404
One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of less than 10 km/h (6 mph), the outputs from both rear speed sensors are 0 km/h (0 mph) for 15 seconds or more.


·

Rear speed sensor RH/LH

·

Speed sensor rotor

·

Sensor installation


C1273
C1274
Stored only during test mode.
·

Rear speed sensor RH/LH

·

Speed sensor rotor

·

Sensor installation



HINT:
·

DTCs C1403 and C1273 are for the rear speed sensor RH.

·

DTCs C1404 and C1274 are for the rear speed sensor LH.



CAUTION / NOTICE / HINT

NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C144929E83
0.833,1.635 0.833,0.771 0.833,0.771 0.979,0.771 false 0.698,2.479 0.938,2.792 0.938,2.792 1.083,2.792 false 0.625,2.927 0.906,3.125 0.281,0.198 10 false *b 2.667,2.906 2.99,3.104 0.323,0.198 10 false *c 1.135,2.698 1.469,2.917 0.333,0.219 10 false *a 1.031,0.677 1.573,0.875 0.542,0.198 10 false 7.8 N*m 0.115,0.115 0.469,0.313 0.354,0.198 10 false *1

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle.

The installation nut is tightened properly.


Torque:

7.8 N*m (80 kgf*cm, 69 in.*lbf)


Text in Illustration
*1 Rear Speed Sensor
*a No clearance
*b OK
*c NG



OK

2.INSPECT REAR SPEED SENSOR TIP

NG

INSTALL REAR SPEED SENSOR CORRECTLY

2.INSPECT REAR SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.




OK

3.INSPECT REAR SPEED SENSOR ROTOR

NG

CLEAN OR REPLACE REAR SPEED SENSOR

3.INSPECT REAR SPEED SENSOR ROTOR
a.

Remove the rear axle hub and bearing assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>REMOVAL).


b.

Check the speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.




OK

4.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)

NG

CLEAN OR REPLACE REAR SPEED SENSOR ROTOR

4.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.


f.

Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK).


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).




OK

NG

5.REPLACE REAR SPEED SENSOR
5.REPLACE REAR SPEED SENSOR

NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more or at least 60 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTCs C1403 and C1404 are not output A
DTCs C1403 and/or C1404 are output B



OK

END

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY