Home › Brake › BRAKE (REAR) › REAR BRAKE
RM1440E _54 Brake _056145 BRAKE (REAR) _0274013 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.

Align the matchmarks and install the rear disc.

HINT:

When replacing the disc with a new one, select the installation position where the disc has the smallest runout.



Hide 47775D 2.INSTALL REAR DISC BRAKE BUSH DUST BOOT

a.
C191828E03
0.844,4.219 1.104,4.396 0.26,0.177 10 false *1

Apply a light coat of lithium soap base glycol grease to the entire circumference of a new rear disc brake bush dust boot where it contacts the rear disc brake cylinder mounting, and the entire inner circumference of both ends.

Text in Illustration
*1 lithium soap base glycol grease

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to the rear disc brake bush dust boot.


NOTICE:

Apply a sufficient amount of lithium soap base glycol grease to the entire circumference of the rear disc brake bush dust boot and rear disc brake cylinder mounting contact surfaces.



b.

Install the rear disc brake bush dust boot to the rear disc brake cylinder mounting.


Hide 47769A 3.INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSH

a.
C191827E03
0.771,4.219 0.979,4.417 0.208,0.198 10 false *1

Apply a light coat of lithium soap base glycol grease to the new rear disc brake cylinder slide bush.

Text in Illustration
*1 Lithium soap base glycol grease

HINT:

Apply at least 0.8 g (0.03 oz.) of lithium soap base glycol grease to the rear disc brake cylinder slide bush.



b.

Install the rear disc brake cylinder slide bush to the rear disc brake cylinder mounting.


c.
C194685E03
0.708,1.698 0.979,1.885 0.271,0.188 10 false *1

Apply a light coat of lithium soap base glycol grease to the cylinder slide pin, insert it into the rear disc brake cylinder slide bush in order to properly grease the parts, and then remove it.

Text in Illustration
*1 Lithium soap base glycol grease


Hide 47713A 4.INSTALL REAR DISC BRAKE CYLINDER HOLE PLUG

a.
C193369E04
0.667,1.74 0.844,1.927 0.177,0.188 10 false *1

Apply a light coat of lithium soap base glycol grease to a new rear disc brake cylinder hole plug.

Text in Illustration
*1 Lithium soap base glycol grease


b.

Install the rear disc brake cylinder hole plug to the rear disc brake cylinder mounting.


Hide 47722A 5.INSTALL REAR DISC BRAKE CYLINDER MOUNTING LH

a.

Install the rear disc brake cylinder mounting and 2 plate washers with the 2 bolts.

Torque:
105 N*m (1071 kgf*cm, 77 ft.*lbf)


Hide 6.INSTALL REAR NO. 1 DISC BRAKE PAD SUPPORT PLATE

a.

Install the 2 rear No. 1 disc brake pad support plates to the rear disc brake cylinder mounting.


Hide 7.INSTALL REAR NO. 2 DISC BRAKE PAD SUPPORT PLATE

a.

Install the 2 rear No. 2 disc brake pad support plates to the rear disc brake cylinder mounting.


Hide 47771A 8.INSTALL REAR DISC BRAKE PAD WEAR INDICATOR PLATE

a.

Install the rear disc brake pad wear indicator plate to the inner side disc brake pad.

HINT:

Install the rear disc brake pad wear indicator facing downward.



Hide 47744C 9.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM

NOTICE:

If necessary, replace the anti-squeal shim when replacing the brake pad.


a.

Install the rear disc brake anti-squeal shims on each rear disc brake pad.

NOTICE:

There should be no oil or grease on the friction surfaces of the brake pads and the rear disc.



Hide 04466 10.INSTALL REAR DISC BRAKE PAD

a.

Install the 2 rear disc brake pads together with the rear disc brake anti-squeal shims to the rear disc brake disc brake cylinder.


Hide 47750A 11.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.
C191829E03
0.677,1.688 0.927,1.896 0.25,0.208 10 false *1

Apply a light coat of lithium soap base glycol grease to the sliding surfaces of the rear disc brake cylinder slide pins.

Text in Illustration
*1 Lithium soap base glycol grease


b.

Install the rear disc brake cylinder with the 2 rear disc brake cylinder slide pins.

Torque:
88 N*m (900 kgf*cm, 65 ft.*lbf)


Hide 47319F 12.CONNECT REAR FLEXIBLE HOSE LH

a.

Connect the rear flexible hose to the rear disc brake cylinder with the union bolt and a new gasket.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)