Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2013.08
RM1440E _55 Steering _056147 POWER ASSIST SYSTEMS _0274019 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C15F0  VFC Solenoid Circuit  


DESCRIPTION

This circuit supplies electric power to the power steering solenoid valve.

The power steering ECU assembly controls the output current to the power steering solenoid valve in accordance with the steering angle signal, steering zero point memory, vehicle speed signal and engine speed signal, adjusting the amount of power steering assist.

DTC Code DTC Detection Condition Trouble area
C15F0 A short or open in the solenoid valve circuit.
·

Harness or connector

·

Vane pump assembly

·

Power steering ECU assembly



WIRING DIAGRAM

C292742E03
4.563,2.75 6.51,2.99 1.948,0.24 10 false Power Steering ECU Assembly 1.031,1.531 2.958,1.75 1.927,0.219 10 false Power Steering Solenoid Valve 1.042,1.385 1.396,1.563 0.354,0.177 10 false B40 4.927,0.99 5.385,1.177 0.458,0.188 10 false SOF+ 4.75,0.906 4.896,1.083 0.146,0.177 10 false 7 2.729,0.875 2.958,1.063 0.229,0.188 10 false 2 1.333,0.906 1.563,1.094 0.229,0.188 10 false 1 4.927,2.021 5.385,2.208 0.458,0.188 10 false SOF- 4.75,1.927 4.875,2.135 0.125,0.208 10 false 8 4.573,2.594 4.948,2.76 0.375,0.167 10 false F41

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SOLENOID CURRENT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / PPS / Data List.

PPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Solenoid Current Solenoid Current/
Min.: 0 mA
Max.: 1000 mA
200 to 950 mA The engine is running and the steering wheel is being turned.

OK:

The normal condition value is displayed on the intelligent tester.




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - POWER STEERING SOLENOID VALVE)
2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - POWER STEERING SOLENOID VALVE)
a.

Disconnect the F41 power steering ECU assembly connector.


b.

Disconnect the B40 power steering solenoid valve connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F41-7 (SOF+) - B40-2 Always Below 1 Ω
F41-8 (SOF-) - B40-1
F41-7 (SOF+) or B40-2 - Body ground Always 10 kΩ or higher
F41-8 (SOF-) or B40-1 - Body ground




OK

3.INSPECT POWER STEERING SOLENOID VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT POWER STEERING SOLENOID VALVE
C294126E02
1.656,0.99 1.115,0.698 true 1.99,1 2.542,0.708 true 1.667,3.146 1.125,2.854 true 1.99,3.146 2.542,2.854 true 0.156,0.156 0.438,0.385 0.281,0.229 10 false *a 0.979,0.531 1.26,0.76 0.281,0.229 10 false 2 1.354,4.219 1.635,4.448 0.281,0.229 10 false (+) 2.135,4.219 2.417,4.448 0.281,0.229 10 false (-) 2.583,0.542 2.865,0.771 0.281,0.229 10 false 1 0.969,2.74 1.146,2.958 0.177,0.219 10 false 2 2.583,2.74 2.865,2.969 0.281,0.229 10 false 1

a.

Disconnect the B40 power steering solenoid valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 6.7 to 7.3 Ω



c.

Connect the positive (+) lead of the battery with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

OK:

Valve moves and makes an operating noise.


Text in Illustration
*a Component without harness connected
(Power Steering Solenoid Valve)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE VANE PUMP ASSEMBLY