Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP
RM1440E _55 Steering _056147 POWER ASSIST SYSTEMS _0274020 VANE PUMP A

POWER ASSIST SYSTEMS  VANE PUMP  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

When installing parts, coat the parts indicated by arrows with power steering fluid (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP>COMPONENTS).


PROCEDURE

Hide 1.INSTALL VANE PUMP HOUSING OIL SEAL

a.

Coat the lip of a new vane pump housing oil seal with MP grease.


b.
C114702E01
0.227,0.347 0.528,0.507 0.301,0.160 10 SST 2.785,0.571 3.086,0.731 0.301,0.160 10 SST 0.996,0.44 0.598,0.44 0.598,0.44 0.976,0.826 false 2.541,0.66 2.744,0.66 2.744,0.66 2.618,1.016 false

Using SST and a press, press in the oil seal.

SST
09950-60010  (09951-00280)
09950-70010  (09951-07100)

NOTICE:

Make sure that the oil seal is installed facing in the correct direction as shown in the illustration.



Hide 2.INSTALL VANE PUMP SHAFT WITH VANE PUMP PULLEY

a.

Coat the inside surface of the bushing in the vane pump front housing with power steering fluid.


b.
C361748E01
1.49,0.99 1.271,0.271 1.271,0.271 1.115,0.271 false 0.927,0.188 1.104,0.385 0.177,0.198 10 false *1

Gradually insert the vane pump shaft with vane pump pulley.

Text in Illustration
*1 Protective Tape

NOTICE:
·

Do not damage the lip of the oil seal in the vane pump front housing.

·

Wrap protective tape around the spline of the vane pump shaft with vane pump pulley in order to prevent damage to the oil seal.




Hide 3.INSTALL VANE PUMP FRONT SIDE PLATE

a.
C132035

Coat a new O-ring with power steering fluid and install it to the vane pump front housing.


b.
C107035

Coat a new O-ring with power steering fluid and install it to the front side plate.


c.
C132040E07
2.729,1.031 1.865,1.031 true 2.646,2.76 2.01,2.76 2.01,2.76 2.01,1.031 true 1.667,0.958 2.104,1.125 0.438,0.167 10 false *a

Align the notch of the front side plate with the notch of the vane pump front housing and install the front side plate.

Text in Illustration
*a Align

NOTICE:

Make sure that the front side plate is installed facing in the correct direction.



Hide 4.INSTALL VANE PUMP CAM RING

a.
C139139E10
2.854,1.135 1.667,1.135 true 2.594,2.698 1.927,2.698 1.927,2.698 1.927,1.146 true 1.365,0.573 1.823,0.115 1.823,0.115 2.135,0.115 true 1.49,1.042 1.917,1.208 0.427,0.167 10 false *a 2.167,0.042 3.125,0.208 0.958,0.167 10 false *b

Align the notch of the cam ring with the notch of the front side plate and install the cam ring with the inscribed mark facing upward.

Text in Illustration
*a Align
*b Inscribed Mark

NOTICE:

Make sure that the cam ring is installed facing in the correct direction.



Hide 5.INSTALL VANE PUMP ROTOR

a.
C107038

Install the vane pump rotor.

HINT:

The vane pump rotor can be installed with either side facing up.



b.

Coat the 10 vane pump plates with power steering fluid.


c.
C141370E02
0.165,2.07 0.724,2.212 0.559,0.142 10 *b 0.981,0.171 1.179,0.362 0.198,0.191 10 *a 0.547,1.115 0.784,0.249 0.784,0.249 0.938,0.249 false

Install the vane pump plates with the round end facing outward.

Text in Illustration
*a Round End
*b Outward

NOTICE:

Make sure that the vane pump plates are installed facing in the correct direction.



Hide 6.INSTALL VANE PUMP SHAFT SNAP RING

a.

Using a screwdriver and snap ring expander, install a new shaft snap ring to the vane pump shaft.

NOTICE:
·

Do not expand the shaft snap ring any further than needed.

·

Make sure that the shaft snap ring fits completely into the groove.

·

Do not damage the vane pump rotor and shaft.




Hide 7.INSTALL VANE PUMP REAR HOUSING

a.
C107040

Coat a new O-ring with power steering fluid and install it to the rear housing.


b.
C136780E11
1.823,0.594 2.875,0.594 false 1.833,1.104 2.385,1.104 2.385,1.104 2.385,0.594 true 2.906,0.51 3.313,0.677 0.406,0.167 10 false *a

Align the straight pin of the rear housing with the notches of the cam ring, front side plate and vane pump front housing.

Text in Illustration
*a Align

NOTICE:

Make sure that the O-ring is not protruding from anywhere when installing the vane pump rear housing.



c.

Install the rear housing with the 4 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 44310 8.SECURE VANE PUMP ASSEMBLY

Hide 9.INSPECT TOTAL PRELOAD

a.

Check that the pump rotates smoothly without abnormal noise.


b.

Temporarily install a service bolt.

Recommended Service Bolt:
Item Value
Thread diameter 10 mm (0.394 in.)
Thread pitch 1.25 mm (0.0492 in.)
Bolt length 50 mm (1.97 in.)



c.
C053369E27
1.177,1.198 2.063,1.74 2.063,1.74 2.167,1.74 true 2.219,1.635 2.448,1.813 0.229,0.177 10 false *a

Using a torque wrench, measure the pump rotating torque.

Text in Illustration
*a Service Bolt

Standard rotating torque:

0.3 N*m (3 kgf*cm, 2 in.*lbf) or less


If the rotating torque is not as specified, check the vane pump housing oil seal.


Hide 10.INSTALL SUCTION PORT UNION

a.

Coat a new O-ring with power steering fluid and install it to the suction port union.


b.

Install the suction port union to the vane pump with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)